Merge branch 'net-phy-support-1000Base-X-auto-negotiation-for-BCM54616S'

Tao Ren says:

====================
net: phy: support 1000Base-X auto-negotiation for BCM54616S

This patch series aims at supporting auto negotiation when BCM54616S is
running in 1000Base-X mode: without the patch series, BCM54616S PHY driver
would report incorrect link speed in 1000Base-X mode.

Patch #1 (of 3) modifies assignment to OR when dealing with dev_flags in
phy_attach_direct function, so that dev_flags updated in BCM54616S PHY's
probe callback won't be lost.

Patch #2 (of 3) adds several genphy_c37_* functions to support clause 37
1000Base-X auto-negotiation, and these functions are called in BCM54616S
PHY driver.

Patch #3 (of 3) detects BCM54616S PHY's operation mode and calls according
genphy_c37_* functions to configure auto-negotiation and parse link
attributes (speed, duplex, and etc.) in 1000Base-X mode.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/phy/broadcom.c

@@ -359,9 +359,9 @@ static int bcm5482_config_init(struct phy_device *phydev)
 		/*
 		 * Select 1000BASE-X register set (primary SerDes)
 		 */
-		reg = bcm_phy_read_shadow(phydev, BCM5482_SHD_MODE);
-		bcm_phy_write_shadow(phydev, BCM5482_SHD_MODE,
-				     reg | BCM5482_SHD_MODE_1000BX);
+		reg = bcm_phy_read_shadow(phydev, BCM54XX_SHD_MODE);
+		bcm_phy_write_shadow(phydev, BCM54XX_SHD_MODE,
+				     reg | BCM54XX_SHD_MODE_1000BX);
 
 		/*
 		 * LED1=ACTIVITYLED, LED3=LINKSPD[2]
@@ -427,12 +427,47 @@ static int bcm5481_config_aneg(struct phy_device *phydev)
 	return ret;
 }
 
+static int bcm54616s_probe(struct phy_device *phydev)
+{
+	int val, intf_sel;
+
+	val = bcm_phy_read_shadow(phydev, BCM54XX_SHD_MODE);
+	if (val < 0)
+		return val;
+
+	/* The PHY is strapped in RGMII-fiber mode when INTERF_SEL[1:0]
+	 * is 01b, and the link between PHY and its link partner can be
+	 * either 1000Base-X or 100Base-FX.
+	 * RGMII-1000Base-X is properly supported, but RGMII-100Base-FX
+	 * support is still missing as of now.
+	 */
+	intf_sel = (val & BCM54XX_SHD_INTF_SEL_MASK) >> 1;
+	if (intf_sel == 1) {
+		val = bcm_phy_read_shadow(phydev, BCM54616S_SHD_100FX_CTRL);
+		if (val < 0)
+			return val;
+
+		/* Bit 0 of the SerDes 100-FX Control register, when set
+		 * to 1, sets the MII/RGMII -> 100BASE-FX configuration.
+		 * When this bit is set to 0, it sets the GMII/RGMII ->
+		 * 1000BASE-X configuration.
+		 */
+		if (!(val & BCM54616S_100FX_MODE))
+			phydev->dev_flags |= PHY_BCM_FLAGS_MODE_1000BX;
+	}
+
+	return 0;
+}
+
 static int bcm54616s_config_aneg(struct phy_device *phydev)
 {
 	int ret;
 
 	/* Aneg firsly. */
-	ret = genphy_config_aneg(phydev);
+	if (phydev->dev_flags & PHY_BCM_FLAGS_MODE_1000BX)
+		ret = genphy_c37_config_aneg(phydev);
+	else
+		ret = genphy_config_aneg(phydev);
 
 	/* Then we can set up the delay. */
 	bcm54xx_config_clock_delay(phydev);
@@ -440,6 +475,18 @@ static int bcm54616s_config_aneg(struct phy_device *phydev)
 	return ret;
 }
 
+static int bcm54616s_read_status(struct phy_device *phydev)
+{
+	int err;
+
+	if (phydev->dev_flags & PHY_BCM_FLAGS_MODE_1000BX)
+		err = genphy_c37_read_status(phydev);
+	else
+		err = genphy_read_status(phydev);
+
+	return err;
+}
+
 static int brcm_phy_setbits(struct phy_device *phydev, int reg, int set)
 {
 	int val;
@@ -631,6 +678,8 @@ static struct phy_driver broadcom_drivers[] = {
 	.config_aneg	= bcm54616s_config_aneg,
 	.ack_interrupt	= bcm_phy_ack_intr,
 	.config_intr	= bcm_phy_config_intr,
+	.read_status	= bcm54616s_read_status,
+	.probe		= bcm54616s_probe,
 }, {
 	.phy_id		= PHY_ID_BCM5464,
 	.phy_id_mask	= 0xfffffff0,

drivers/net/phy/phy_device.c

@@ -1270,7 +1270,7 @@ int phy_attach_direct(struct net_device *dev, struct phy_device *phydev,
 			phydev_err(phydev, "error creating 'phy_standalone' sysfs entry\n");
 	}
 
-	phydev->dev_flags = flags;
+	phydev->dev_flags |= flags;
 
 	phydev->interface = interface;
 
@@ -1607,6 +1607,40 @@ static int genphy_config_advert(struct phy_device *phydev)
 	return changed;
 }
 
+/**
+ * genphy_c37_config_advert - sanitize and advertise auto-negotiation parameters
+ * @phydev: target phy_device struct
+ *
+ * Description: Writes MII_ADVERTISE with the appropriate values,
+ *   after sanitizing the values to make sure we only advertise
+ *   what is supported.  Returns < 0 on error, 0 if the PHY's advertisement
+ *   hasn't changed, and > 0 if it has changed. This function is intended
+ *   for Clause 37 1000Base-X mode.
+ */
+static int genphy_c37_config_advert(struct phy_device *phydev)
+{
+	u16 adv = 0;
+
+	/* Only allow advertising what this PHY supports */
+	linkmode_and(phydev->advertising, phydev->advertising,
+		     phydev->supported);
+
+	if (linkmode_test_bit(ETHTOOL_LINK_MODE_1000baseX_Full_BIT,
+			      phydev->advertising))
+		adv |= ADVERTISE_1000XFULL;
+	if (linkmode_test_bit(ETHTOOL_LINK_MODE_Pause_BIT,
+			      phydev->advertising))
+		adv |= ADVERTISE_1000XPAUSE;
+	if (linkmode_test_bit(ETHTOOL_LINK_MODE_Asym_Pause_BIT,
+			      phydev->advertising))
+		adv |= ADVERTISE_1000XPSE_ASYM;
+
+	return phy_modify_changed(phydev, MII_ADVERTISE,
+				  ADVERTISE_1000XFULL | ADVERTISE_1000XPAUSE |
+				  ADVERTISE_1000XHALF | ADVERTISE_1000XPSE_ASYM,
+				  adv);
+}
+
 /**
  * genphy_config_eee_advert - disable unwanted eee mode advertisement
  * @phydev: target phy_device struct
@@ -1715,6 +1749,54 @@ int __genphy_config_aneg(struct phy_device *phydev, bool changed)
 }
 EXPORT_SYMBOL(__genphy_config_aneg);
 
+/**
+ * genphy_c37_config_aneg - restart auto-negotiation or write BMCR
+ * @phydev: target phy_device struct
+ *
+ * Description: If auto-negotiation is enabled, we configure the
+ *   advertising, and then restart auto-negotiation.  If it is not
+ *   enabled, then we write the BMCR. This function is intended
+ *   for use with Clause 37 1000Base-X mode.
+ */
+int genphy_c37_config_aneg(struct phy_device *phydev)
+{
+	int err, changed;
+
+	if (phydev->autoneg != AUTONEG_ENABLE)
+		return genphy_setup_forced(phydev);
+
+	err = phy_modify(phydev, MII_BMCR, BMCR_SPEED1000 | BMCR_SPEED100,
+			 BMCR_SPEED1000);
+	if (err)
+		return err;
+
+	changed = genphy_c37_config_advert(phydev);
+	if (changed < 0) /* error */
+		return changed;
+
+	if (!changed) {
+		/* Advertisement hasn't changed, but maybe aneg was never on to
+		 * begin with?  Or maybe phy was isolated?
+		 */
+		int ctl = phy_read(phydev, MII_BMCR);
+
+		if (ctl < 0)
+			return ctl;
+
+		if (!(ctl & BMCR_ANENABLE) || (ctl & BMCR_ISOLATE))
+			changed = 1; /* do restart aneg */
+	}
+
+	/* Only restart aneg if we are advertising something different
+	 * than we were before.
+	 */
+	if (changed > 0)
+		return genphy_restart_aneg(phydev);
+
+	return 0;
+}
+EXPORT_SYMBOL(genphy_c37_config_aneg);
+
 /**
  * genphy_aneg_done - return auto-negotiation status
  * @phydev: target phy_device struct
@@ -1886,6 +1968,63 @@ int genphy_read_status(struct phy_device *phydev)
 }
 EXPORT_SYMBOL(genphy_read_status);
 
+/**
+ * genphy_c37_read_status - check the link status and update current link state
+ * @phydev: target phy_device struct
+ *
+ * Description: Check the link, then figure out the current state
+ *   by comparing what we advertise with what the link partner
+ *   advertises. This function is for Clause 37 1000Base-X mode.
+ */
+int genphy_c37_read_status(struct phy_device *phydev)
+{
+	int lpa, err, old_link = phydev->link;
+
+	/* Update the link, but return if there was an error */
+	err = genphy_update_link(phydev);
+	if (err)
+		return err;
+
+	/* why bother the PHY if nothing can have changed */
+	if (phydev->autoneg == AUTONEG_ENABLE && old_link && phydev->link)
+		return 0;
+
+	phydev->duplex = DUPLEX_UNKNOWN;
+	phydev->pause = 0;
+	phydev->asym_pause = 0;
+
+	if (phydev->autoneg == AUTONEG_ENABLE && phydev->autoneg_complete) {
+		lpa = phy_read(phydev, MII_LPA);
+		if (lpa < 0)
+			return lpa;
+
+		linkmode_mod_bit(ETHTOOL_LINK_MODE_Autoneg_BIT,
+				 phydev->lp_advertising, lpa & LPA_LPACK);
+		linkmode_mod_bit(ETHTOOL_LINK_MODE_1000baseX_Full_BIT,
+				 phydev->lp_advertising, lpa & LPA_1000XFULL);
+		linkmode_mod_bit(ETHTOOL_LINK_MODE_Pause_BIT,
+				 phydev->lp_advertising, lpa & LPA_1000XPAUSE);
+		linkmode_mod_bit(ETHTOOL_LINK_MODE_Asym_Pause_BIT,
+				 phydev->lp_advertising,
+				 lpa & LPA_1000XPAUSE_ASYM);
+
+		phy_resolve_aneg_linkmode(phydev);
+	} else if (phydev->autoneg == AUTONEG_DISABLE) {
+		int bmcr = phy_read(phydev, MII_BMCR);
+
+		if (bmcr < 0)
+			return bmcr;
+
+		if (bmcr & BMCR_FULLDPLX)
+			phydev->duplex = DUPLEX_FULL;
+		else
+			phydev->duplex = DUPLEX_HALF;
+	}
+
+	return 0;
+}
+EXPORT_SYMBOL(genphy_c37_read_status);
+
 /**
  * genphy_soft_reset - software reset the PHY via BMCR_RESET bit
  * @phydev: target phy_device struct

include/linux/brcmphy.h

@@ -200,9 +200,15 @@
 #define BCM5482_SHD_SSD		0x14	/* 10100: Secondary SerDes control */
 #define BCM5482_SHD_SSD_LEDM	0x0008	/* SSD LED Mode enable */
 #define BCM5482_SHD_SSD_EN	0x0001	/* SSD enable */
-#define BCM5482_SHD_MODE	0x1f	/* 11111: Mode Control Register */
-#define BCM5482_SHD_MODE_1000BX	0x0001	/* Enable 1000BASE-X registers */
 
+/* 10011: SerDes 100-FX Control Register */
+#define BCM54616S_SHD_100FX_CTRL	0x13
+#define	BCM54616S_100FX_MODE		BIT(0)	/* 100-FX SerDes Enable */
+
+/* 11111: Mode Control Register */
+#define BCM54XX_SHD_MODE		0x1f
+#define BCM54XX_SHD_INTF_SEL_MASK	GENMASK(2, 1)	/* INTERF_SEL[1:0] */
+#define BCM54XX_SHD_MODE_1000BX		BIT(0)	/* Enable 1000-X registers */
 
 /*
  * EXPANSION SHADOW ACCESS REGISTERS.  (PHY REG 0x15, 0x16, and 0x17)

include/linux/phy.h

@@ -1106,6 +1106,10 @@ int genphy_read_mmd_unsupported(struct phy_device *phdev, int devad,
 int genphy_write_mmd_unsupported(struct phy_device *phdev, int devnum,
 				 u16 regnum, u16 val);
 
+/* Clause 37 */
+int genphy_c37_config_aneg(struct phy_device *phydev);
+int genphy_c37_read_status(struct phy_device *phydev);
+
 /* Clause 45 PHY */
 int genphy_c45_restart_aneg(struct phy_device *phydev);
 int genphy_c45_check_and_restart_aneg(struct phy_device *phydev, bool restart);