firmware: arm_scmi: Add xfer helpers to provide raw access

Add a few SCMI helpers useful to implement SCMI raw access support.
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Vincent Guittot <vincent.guittot@linaro.org>
Link: https://lore.kernel.org/r/20230118121426.492864-6-cristian.marussi@arm.comSigned-off-by: Sudeep Holla <sudeep.holla@arm.com>

drivers/firmware/arm_scmi/common.h

@@ -229,6 +229,18 @@ static inline bool is_polling_enabled(struct scmi_chan_info *cinfo,
 		is_transport_polling_capable(desc);
 }
 
+void scmi_xfer_raw_put(const struct scmi_handle *handle,
+		       struct scmi_xfer *xfer);
+struct scmi_xfer *scmi_xfer_raw_get(const struct scmi_handle *handle);
+struct scmi_chan_info *
+scmi_xfer_raw_channel_get(const struct scmi_handle *handle, u8 protocol_id);
+
+int scmi_xfer_raw_inflight_register(const struct scmi_handle *handle,
+				    struct scmi_xfer *xfer);
+
+int scmi_xfer_raw_wait_for_message_response(struct scmi_chan_info *cinfo,
+					    struct scmi_xfer *xfer,
+					    unsigned int timeout_ms);
 #ifdef CONFIG_ARM_SCMI_TRANSPORT_MAILBOX
 extern const struct scmi_desc scmi_mailbox_desc;
 #endif

drivers/firmware/arm_scmi/driver.c

@@ -450,6 +450,53 @@ scmi_xfer_inflight_register_unlocked(struct scmi_xfer *xfer,
 	xfer->pending = true;
 }
 
+/**
+ * scmi_xfer_inflight_register  - Try to register an xfer as in-flight
+ *
+ * @xfer: The xfer to register
+ * @minfo: Pointer to Tx/Rx Message management info based on channel type
+ *
+ * Note that this helper does NOT assume anything about the sequence number
+ * that was baked into the provided xfer, so it checks at first if it can
+ * be mapped to a free slot and fails with an error if another xfer with the
+ * same sequence number is currently still registered as in-flight.
+ *
+ * Return: 0 on Success or -EBUSY if sequence number embedded in the xfer
+ *	   could not rbe mapped to a free slot in the xfer_alloc_table.
+ */
+static int scmi_xfer_inflight_register(struct scmi_xfer *xfer,
+				       struct scmi_xfers_info *minfo)
+{
+	int ret = 0;
+	unsigned long flags;
+
+	spin_lock_irqsave(&minfo->xfer_lock, flags);
+	if (!test_bit(xfer->hdr.seq, minfo->xfer_alloc_table))
+		scmi_xfer_inflight_register_unlocked(xfer, minfo);
+	else
+		ret = -EBUSY;
+	spin_unlock_irqrestore(&minfo->xfer_lock, flags);
+
+	return ret;
+}
+
+/**
+ * scmi_xfer_raw_inflight_register  - An helper to register the given xfer as in
+ * flight on the TX channel, if possible.
+ *
+ * @handle: Pointer to SCMI entity handle
+ * @xfer: The xfer to register
+ *
+ * Return: 0 on Success, error otherwise
+ */
+int scmi_xfer_raw_inflight_register(const struct scmi_handle *handle,
+				    struct scmi_xfer *xfer)
+{
+	struct scmi_info *info = handle_to_scmi_info(handle);
+
+	return scmi_xfer_inflight_register(xfer, &info->tx_minfo);
+}
+
 /**
  * scmi_xfer_pending_set  - Pick a proper sequence number and mark the xfer
  * as pending in-flight
@@ -525,6 +572,63 @@ static struct scmi_xfer *scmi_xfer_get(const struct scmi_handle *handle,
 	return xfer;
 }
 
+/**
+ * scmi_xfer_raw_get  - Helper to get a bare free xfer from the TX channel
+ *
+ * @handle: Pointer to SCMI entity handle
+ *
+ * Note that xfer is taken from the TX channel structures.
+ *
+ * Return: A valid xfer on Success, or an error-pointer otherwise
+ */
+struct scmi_xfer *scmi_xfer_raw_get(const struct scmi_handle *handle)
+{
+	struct scmi_xfer *xfer;
+	struct scmi_info *info = handle_to_scmi_info(handle);
+
+	xfer = scmi_xfer_get(handle, &info->tx_minfo);
+	if (!IS_ERR(xfer))
+		xfer->flags |= SCMI_XFER_FLAG_IS_RAW;
+
+	return xfer;
+}
+
+/**
+ * scmi_xfer_raw_channel_get  - Helper to get a reference to the proper channel
+ * to use for a specific protocol_id Raw transaction.
+ *
+ * @handle: Pointer to SCMI entity handle
+ * @protocol_id: Identifier of the protocol
+ *
+ * Note that in a regular SCMI stack, usually, a protocol has to be defined in
+ * the DT to have an associated channel and be usable; but in Raw mode any
+ * protocol in range is allowed, re-using the Base channel, so as to enable
+ * fuzzing on any protocol without the need of a fully compiled DT.
+ *
+ * Return: A reference to the channel to use, or an ERR_PTR
+ */
+struct scmi_chan_info *
+scmi_xfer_raw_channel_get(const struct scmi_handle *handle, u8 protocol_id)
+{
+	struct scmi_chan_info *cinfo;
+	struct scmi_info *info = handle_to_scmi_info(handle);
+
+	cinfo = idr_find(&info->tx_idr, protocol_id);
+	if (!cinfo) {
+		if (protocol_id == SCMI_PROTOCOL_BASE)
+			return ERR_PTR(-EINVAL);
+		/* Use Base channel for protocols not defined for DT */
+		cinfo = idr_find(&info->tx_idr, SCMI_PROTOCOL_BASE);
+		if (!cinfo)
+			return ERR_PTR(-EINVAL);
+		dev_warn_once(handle->dev,
+			      "Using Base channel for protocol 0x%X\n",
+			      protocol_id);
+	}
+
+	return cinfo;
+}
+
 /**
  * __scmi_xfer_put() - Release a message
  *
@@ -553,6 +657,23 @@ __scmi_xfer_put(struct scmi_xfers_info *minfo, struct scmi_xfer *xfer)
 	spin_unlock_irqrestore(&minfo->xfer_lock, flags);
 }
 
+/**
+ * scmi_xfer_raw_put  - Release an xfer that was taken by @scmi_xfer_raw_get
+ *
+ * @handle: Pointer to SCMI entity handle
+ * @xfer: A reference to the xfer to put
+ *
+ * Note that as with other xfer_put() handlers the xfer is really effectively
+ * released only if there are no more users on the system.
+ */
+void scmi_xfer_raw_put(const struct scmi_handle *handle, struct scmi_xfer *xfer)
+{
+	struct scmi_info *info = handle_to_scmi_info(handle);
+
+	xfer->flags &= ~SCMI_XFER_FLAG_IS_RAW;
+	return __scmi_xfer_put(&info->tx_minfo, xfer);
+}
+
 /**
  * scmi_xfer_lookup_unlocked  -  Helper to lookup an xfer_id
  *
@@ -979,6 +1100,32 @@ static int scmi_wait_for_message_response(struct scmi_chan_info *cinfo,
 				   info->desc->max_rx_timeout_ms);
 }
 
+/**
+ * scmi_xfer_raw_wait_for_message_response  - An helper to wait for a message
+ * reply to an xfer raw request on a specific channel for the required timeout.
+ *
+ * @cinfo: SCMI channel info
+ * @xfer: Reference to the transfer being waited for.
+ * @timeout_ms: The maximum timeout in milliseconds
+ *
+ * Return: 0 on Success, error otherwise.
+ */
+int scmi_xfer_raw_wait_for_message_response(struct scmi_chan_info *cinfo,
+					    struct scmi_xfer *xfer,
+					    unsigned int timeout_ms)
+{
+	int ret;
+	struct scmi_info *info = handle_to_scmi_info(cinfo->handle);
+	struct device *dev = info->dev;
+
+	ret = scmi_wait_for_reply(dev, info->desc, cinfo, xfer, timeout_ms);
+	if (ret)
+		dev_dbg(dev, "timed out in RAW response - HDR:%08X\n",
+			pack_scmi_header(&xfer->hdr));
+
+	return ret;
+}
+
 /**
  * do_xfer() - Do one transfer
  *