mtd: rawnand: gpmi: add 'support_edo_timing' in gpmi_devdata

Introduce a boolean flag, 'support_edo_timing', within gpmi_devdata to
simplify the logic check in gpmi_setup_interface(). This is made in
preparation for adding support for imx8qxp gpmi.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240520-gpmi_nand-v2-3-e3017e4c9da5@nxp.com

drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c

@@ -983,7 +983,7 @@ static int gpmi_setup_interface(struct nand_chip *chip, int chipnr,
 		return PTR_ERR(sdr);
 
 	/* Only MX28/MX6 GPMI controller can reach EDO timings */
-	if (sdr->tRC_min <= 25000 && !GPMI_IS_MX28(this) && !GPMI_IS_MX6(this))
+	if (sdr->tRC_min <= 25000 && !this->devdata->support_edo_timing)
 		return -ENOTSUPP;
 
 	/* Stop here if this call was just a check */
@@ -1142,6 +1142,7 @@ static const struct gpmi_devdata gpmi_devdata_imx28 = {
 	.type = IS_MX28,
 	.bch_max_ecc_strength = 20,
 	.max_chain_delay = 16000,
+	.support_edo_timing = true,
 	.clks = gpmi_clks_for_mx2x,
 	.clks_count = ARRAY_SIZE(gpmi_clks_for_mx2x),
 };
@@ -1154,6 +1155,7 @@ static const struct gpmi_devdata gpmi_devdata_imx6q = {
 	.type = IS_MX6Q,
 	.bch_max_ecc_strength = 40,
 	.max_chain_delay = 12000,
+	.support_edo_timing = true,
 	.clks = gpmi_clks_for_mx6,
 	.clks_count = ARRAY_SIZE(gpmi_clks_for_mx6),
 };
@@ -1162,6 +1164,7 @@ static const struct gpmi_devdata gpmi_devdata_imx6sx = {
 	.type = IS_MX6SX,
 	.bch_max_ecc_strength = 62,
 	.max_chain_delay = 12000,
+	.support_edo_timing = true,
 	.clks = gpmi_clks_for_mx6,
 	.clks_count = ARRAY_SIZE(gpmi_clks_for_mx6),
 };
@@ -1174,6 +1177,7 @@ static const struct gpmi_devdata gpmi_devdata_imx7d = {
 	.type = IS_MX7D,
 	.bch_max_ecc_strength = 62,
 	.max_chain_delay = 12000,
+	.support_edo_timing = true,
 	.clks = gpmi_clks_for_mx7d,
 	.clks_count = ARRAY_SIZE(gpmi_clks_for_mx7d),
 };

drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.h

@@ -86,6 +86,7 @@ struct gpmi_devdata {
 	int max_chain_delay; /* See the SDR EDO mode */
 	const char * const *clks;
 	const int clks_count;
+	bool support_edo_timing;
 };
 
 /**