Merge branches 'ntrig', 'picolcd', 'prodikeys' and 'roccat-kone' into for-linus

Conflicts:
	drivers/hid/Makefile

Documentation/ABI/testing/sysfs-driver-hid-picolcd

+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/<hid-bus>:<vendor-id>:<product-id>.<num>/operation_mode
+Date:		March 2010
+Contact:	Bruno Prémont <bonbons@linux-vserver.org>
+Description:	Make it possible to switch the PicoLCD device between LCD
+		(firmware) and bootloader (flasher) operation modes.
+
+		Reading: returns list of available modes, the active mode being
+		enclosed in brackets ('[' and ']')
+
+		Writing: causes operation mode switch. Permitted values are
+		the non-active mode names listed when read.
+
+		Note: when switching mode the current PicoLCD HID device gets
+		disconnected and reconnects after above delay (see attribute
+		operation_mode_delay for its value).
+
+
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/<hid-bus>:<vendor-id>:<product-id>.<num>/operation_mode_delay
+Date:		April 2010
+Contact:	Bruno Prémont <bonbons@linux-vserver.org>
+Description:	Delay PicoLCD waits before restarting in new mode when
+		operation_mode has changed.
+
+		Reading/Writing: It is expressed in ms and permitted range is
+		0..30000ms.
+
+
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/<hid-bus>:<vendor-id>:<product-id>.<num>/fb_update_rate
+Date:		March 2010
+Contact:	Bruno Prémont <bonbons@linux-vserver.org>
+Description:	Make it possible to adjust defio refresh rate.
+
+		Reading: returns list of available refresh rates (expressed in Hz),
+		the active refresh rate being enclosed in brackets ('[' and ']')
+
+		Writing: accepts new refresh rate expressed in integer Hz
+		within permitted rates.
+
+		Note: As device can barely do 2 complete refreshes a second
+		it only makes sense to adjust this value if only one or two
+		tiles get changed and it's not appropriate to expect the application
+		to flush it's tiny changes explicitely at higher than default rate.
+

Documentation/ABI/testing/sysfs-driver-hid-prodikeys

+What:		/sys/bus/hid/drivers/prodikeys/.../channel
+Date:		April 2010
+KernelVersion:	2.6.34
+Contact:	Don Prince <dhprince.devel@yahoo.co.uk>
+Description:
+		Allows control (via software) the midi channel to which
+		that the pc-midi keyboard will output.midi data.
+		Range: 0..15
+		Type:  Read/write
+What:		/sys/bus/hid/drivers/prodikeys/.../sustain
+Date:		April 2010
+KernelVersion:	2.6.34
+Contact:	Don Prince <dhprince.devel@yahoo.co.uk>
+Description:
+		Allows control (via software) the sustain duration of a
+		note held by the pc-midi driver.
+		0 means sustain mode is disabled.
+		Range: 0..5000 (milliseconds)
+		Type:  Read/write
+What:		/sys/bus/hid/drivers/prodikeys/.../octave
+Date:		April 2010
+KernelVersion:	2.6.34
+Contact:	Don Prince <dhprince.devel@yahoo.co.uk>
+Description:
+		Controls the octave shift modifier in the pc-midi driver.
+		The octave can be shifted via software up/down 2 octaves.
+		0 means the no ocatve shift.
+		Range: -2..2 (minus 2 to plus 2)
+		Type: Read/Write

Documentation/ABI/testing/sysfs-driver-hid-roccat-kone

+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/actual_dpi
+Date:		March 2010
+Contact:	Stefan Achatz <erazor_de@users.sourceforge.net>
+Description:	It is possible to switch the dpi setting of the mouse with the
+		press of a button.
+		When read, this file returns the raw number of the actual dpi
+		setting reported by the mouse. This number has to be further
+		processed to receive the real dpi value.
+
+		VALUE DPI
+		1     800
+		2     1200
+		3     1600
+		4     2000
+		5     2400
+		6     3200
+
+		This file is readonly.
+
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/actual_profile
+Date:		March 2010
+Contact:	Stefan Achatz <erazor_de@users.sourceforge.net>
+Description:	When read, this file returns the number of the actual profile.
+		This file is readonly.
+
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/firmware_version
+Date:		March 2010
+Contact:	Stefan Achatz <erazor_de@users.sourceforge.net>
+Description:	When read, this file returns the raw integer version number of the
+		firmware reported by the mouse. Using the integer value eases
+		further usage in other programs. To receive the real version
+		number the decimal point has to be shifted 2 positions to the
+		left. E.g. a returned value of 138 means 1.38
+		This file is readonly.
+
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/kone_driver_version
+Date:		March 2010
+Contact:	Stefan Achatz <erazor_de@users.sourceforge.net>
+Description:	When read, this file returns the driver version.
+		The format of the string is "v<major>.<minor>.<patchlevel>".
+		This attribute is used by the userland tools to find the sysfs-
+		paths of installed kone-mice and determine the capabilites of
+		the driver. Versions of this driver for old kernels replace
+		usbhid instead of generic-usb. The way to scan for this file
+		has been chosen to provide a consistent way for all supported
+		kernel versions.
+		This file is readonly.
+
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/profile[1-5]
+Date:		March 2010
+Contact:	Stefan Achatz <erazor_de@users.sourceforge.net>
+Description:	The mouse can store 5 profiles which can be switched by the
+                press of a button. A profile holds informations like button
+                mappings, sensitivity, the colors of the 5 leds and light
+                effects.
+                When read, these files return the respective profile. The
+                returned data is 975 bytes in size.
+		When written, this file lets one write the respective profile
+		data back to the mouse. The data has to be 975 bytes long.
+		The mouse will reject invalid data, whereas the profile number
+		stored in the profile doesn't need to fit the number of the
+		store.
+
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/settings
+Date:		March 2010
+Contact:	Stefan Achatz <erazor_de@users.sourceforge.net>
+Description:	When read, this file returns the settings stored in the mouse.
+		The size of the data is 36 bytes and holds information like the
+		startup_profile, tcu state and calibration_data.
+		When written, this file lets write settings back to the mouse.
+		The data has to be 36 bytes long. The mouse will reject invalid
+		data.
+
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/startup_profile
+Date:		March 2010
+Contact:	Stefan Achatz <erazor_de@users.sourceforge.net>
+Description:	The integer value of this attribute ranges from 1 to 5.
+                When read, this attribute returns the number of the profile
+                that's active when the mouse is powered on.
+		When written, this file sets the number of the startup profile
+		and the mouse activates this profile immediately.
+
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/tcu
+Date:		March 2010
+Contact:	Stefan Achatz <erazor_de@users.sourceforge.net>
+Description:	The mouse has a "Tracking Control Unit" which lets the user
+		calibrate the laser power to fit the mousepad surface.
+		When read, this file returns the current state of the TCU,
+		where 0 means off and 1 means on.
+		Writing 0 in this file will switch the TCU off.
+		Writing 1 in this file will start the calibration which takes
+		around 6 seconds to complete and activates the TCU.
+
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/weight
+Date:		March 2010
+Contact:	Stefan Achatz <erazor_de@users.sourceforge.net>
+Description:	The mouse can be equipped with one of four supplied weights
+		ranging from 5 to 20 grams which are recognized by the mouse
+		and its value can be read out. When read, this file returns the
+		raw value returned by the mouse which eases further processing
+		in other software.
+		The values map to the weights as follows:
+
+		VALUE WEIGHT
+		0     none
+		1     5g
+		2     10g
+		3     15g
+		4     20g
+
+		This file is readonly.

drivers/hid/Kconfig

@@ -106,6 +106,21 @@ config HID_CHICONY
 	---help---
 	Support for Chicony Tactical pad.
 
+config HID_PRODIKEYS
+	tristate "Prodikeys PC-MIDI Keyboard support"
+	depends on USB_HID && SND
+	select SND_RAWMIDI
+	---help---
+	Support for Prodikeys PC-MIDI Keyboard device support.
+	Say Y here to enable support for this device.
+	- Prodikeys PC-MIDI keyboard.
+	  The Prodikeys PC-MIDI acts as a USB Audio device, with one MIDI
+	  input and one MIDI output. These MIDI jacks appear as
+	  a sound "card" in the ALSA sound system.
+	  Note: if you say N here, this device will still function as a basic
+	  multimedia keyboard, but will lack support for the musical keyboard
+	  and some additional multimedia keys.
+
 config HID_CYPRESS
 	tristate "Cypress" if EMBEDDED
 	depends on USB_HID
@@ -274,12 +289,76 @@ config HID_PETALYNX
 	---help---
 	Support for Petalynx Maxter remote control.
 
+config HID_PICOLCD
+	tristate "PicoLCD (graphic version)"
+	depends on USB_HID
+	---help---
+	  This provides support for Minibox PicoLCD devices, currently
+	  only the graphical ones are supported.
+
+	  This includes support for the following device features:
+	  - Keypad
+	  - Switching between Firmware and Flash mode
+	  - EEProm / Flash access     (via debugfs)
+	  Features selectively enabled:
+	  - Framebuffer for monochrome 256x64 display
+	  - Backlight control
+	  - Contrast control
+	  - General purpose outputs
+	  Features that are not (yet) supported:
+	  - IR
+
+config HID_PICOLCD_FB
+	bool "Framebuffer support" if EMBEDDED
+	default !EMBEDDED
+	depends on HID_PICOLCD
+	depends on HID_PICOLCD=FB || FB=y
+	select FB_DEFERRED_IO
+	select FB_SYS_FILLRECT
+	select FB_SYS_COPYAREA
+	select FB_SYS_IMAGEBLIT
+	select FB_SYS_FOPS
+	---help---
+	  Provide access to PicoLCD's 256x64 monochrome display via a
+	  frambuffer device.
+
+config HID_PICOLCD_BACKLIGHT
+	bool "Backlight control" if EMBEDDED
+	default !EMBEDDED
+	depends on HID_PICOLCD
+	depends on HID_PICOLCD=BACKLIGHT_CLASS_DEVICE || BACKLIGHT_CLASS_DEVICE=y
+	---help---
+	  Provide access to PicoLCD's backlight control via backlight
+	  class.
+
+config HID_PICOLCD_LCD
+	bool "Contrast control" if EMBEDDED
+	default !EMBEDDED
+	depends on HID_PICOLCD
+	depends on HID_PICOLCD=LCD_CLASS_DEVICE || LCD_CLASS_DEVICE=y
+	---help---
+	  Provide access to PicoLCD's LCD contrast via lcd class.
+
+config HID_PICOLCD_LEDS
+	bool "GPO via leds class" if EMBEDDED
+	default !EMBEDDED
+	depends on HID_PICOLCD
+	depends on HID_PICOLCD=LEDS_CLASS || LEDS_CLASS=y
+	---help---
+	  Provide access to PicoLCD's GPO pins via leds class.
+
 config HID_QUANTA
 	tristate "Quanta Optical Touch"
 	depends on USB_HID
 	---help---
 	Support for Quanta Optical Touch dual-touch panels.
 
+config HID_ROCCAT_KONE
+	tristate "Roccat Kone Mouse support"
+	depends on USB_HID
+	---help---
+	Support for Roccat Kone mouse.
+
 config HID_SAMSUNG
 	tristate "Samsung" if EMBEDDED
 	depends on USB_HID

drivers/hid/Makefile

@@ -43,9 +43,12 @@ obj-$(CONFIG_HID_MONTEREY)	+= hid-monterey.o
 obj-$(CONFIG_HID_MOSART)	+= hid-mosart.o
 obj-$(CONFIG_HID_NTRIG)		+= hid-ntrig.o
 obj-$(CONFIG_HID_ORTEK)		+= hid-ortek.o
+obj-$(CONFIG_HID_PRODIKEYS)	+= hid-prodikeys.o
 obj-$(CONFIG_HID_QUANTA)	+= hid-quanta.o
 obj-$(CONFIG_HID_PANTHERLORD)	+= hid-pl.o
 obj-$(CONFIG_HID_PETALYNX)	+= hid-petalynx.o
+obj-$(CONFIG_HID_PICOLCD)	+= hid-picolcd.o
+obj-$(CONFIG_HID_ROCCAT_KONE)	+= hid-roccat-kone.o
 obj-$(CONFIG_HID_SAMSUNG)	+= hid-samsung.o
 obj-$(CONFIG_HID_SMARTJOYPLUS)	+= hid-sjoy.o
 obj-$(CONFIG_HID_SONY)		+= hid-sony.o

drivers/hid/hid-core.c

@@ -1287,6 +1287,7 @@ static const struct hid_device_id hid_blacklist[] = {
 	{ HID_USB_DEVICE(USB_VENDOR_ID_CHERRY, USB_DEVICE_ID_CHERRY_CYMOTION) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_CHERRY, USB_DEVICE_ID_CHERRY_CYMOTION_SOLAR) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_CHICONY, USB_DEVICE_ID_CHICONY_TACTICAL_PAD) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_CREATIVELABS, USB_DEVICE_ID_PRODIKEYS_PCMIDI) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_CYPRESS, USB_DEVICE_ID_CYPRESS_BARCODE_1) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_CYPRESS, USB_DEVICE_ID_CYPRESS_BARCODE_2) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_CYPRESS, USB_DEVICE_ID_CYPRESS_BARCODE_3) },
@@ -1326,6 +1327,8 @@ static const struct hid_device_id hid_blacklist[] = {
 	{ HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, USB_DEVICE_ID_LOGITECH_RUMBLEPAD2) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, USB_DEVICE_ID_SPACETRAVELLER) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, USB_DEVICE_ID_SPACENAVIGATOR) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_MICROCHIP, USB_DEVICE_ID_PICOLCD) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_MICROCHIP, USB_DEVICE_ID_PICOLCD_BOOTLOADER) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_SIDEWINDER_GV) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_NE4K) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_LK6K) },
@@ -1337,6 +1340,7 @@ static const struct hid_device_id hid_blacklist[] = {
 	{ HID_USB_DEVICE(USB_VENDOR_ID_PETALYNX, USB_DEVICE_ID_PETALYNX_MAXTER_REMOTE) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_QUANTA, USB_DEVICE_ID_QUANTA_OPTICAL_TOUCH) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_QUANTA, USB_DEVICE_ID_PIXART_IMAGING_INC_OPTICAL_TOUCH_SCREEN) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_ROCCAT, USB_DEVICE_ID_ROCCAT_KONE) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_SAMSUNG, USB_DEVICE_ID_SAMSUNG_IR_REMOTE) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_SAMSUNG, USB_DEVICE_ID_SAMSUNG_WIRELESS_KBD_MOUSE) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_SONY, USB_DEVICE_ID_SONY_PS3_CONTROLLER) },

drivers/hid/hid-ids.h

@@ -156,6 +156,9 @@
 #define USB_DEVICE_ID_CODEMERCS_IOW_FIRST	0x1500
 #define USB_DEVICE_ID_CODEMERCS_IOW_LAST	0x15ff
 
+#define USB_VENDOR_ID_CREATIVELABS	0x041e
+#define USB_DEVICE_ID_PRODIKEYS_PCMIDI	0x2801
+
 #define USB_VENDOR_ID_CYGNAL		0x10c4
 #define USB_DEVICE_ID_CYGNAL_RADIO_SI470X	0x818a
 
@@ -354,6 +357,8 @@
 #define USB_VENDOR_ID_MICROCHIP		0x04d8
 #define USB_DEVICE_ID_PICKIT1		0x0032
 #define USB_DEVICE_ID_PICKIT2		0x0033
+#define USB_DEVICE_ID_PICOLCD		0xc002
+#define USB_DEVICE_ID_PICOLCD_BOOTLOADER	0xf002
 
 #define USB_VENDOR_ID_MICROSOFT		0x045e
 #define USB_DEVICE_ID_SIDEWINDER_GV	0x003b
@@ -412,6 +417,9 @@
 #define USB_VENDOR_ID_PRODIGE		0x05af
 #define USB_DEVICE_ID_PRODIGE_CORDLESS	0x3062
 
+#define USB_VENDOR_ID_ROCCAT		0x1e7d
+#define USB_DEVICE_ID_ROCCAT_KONE	0x2ced
+
 #define USB_VENDOR_ID_SAITEK		0x06a3
 #define USB_DEVICE_ID_SAITEK_RUMBLEPAD	0xff17
 

drivers/hid/hid-roccat-kone.h

+#ifndef __HID_ROCCAT_KONE_H
+#define __HID_ROCCAT_KONE_H
+
+/*
+ * Copyright (c) 2010 Stefan Achatz <erazor_de@users.sourceforge.net>
+ */
+
+/*
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ */
+
+#include <linux/types.h>
+
+#define ROCCAT_KONE_DRIVER_VERSION "v0.3.1"
+
+#pragma pack(push)
+#pragma pack(1)
+
+struct kone_keystroke {
+	uint8_t key;
+	uint8_t action;
+	uint16_t period; /* in milliseconds */
+};
+
+enum kone_keystroke_buttons {
+	kone_keystroke_button_1 = 0xf0, /* left mouse button */
+	kone_keystroke_button_2 = 0xf1, /* right mouse button */
+	kone_keystroke_button_3 = 0xf2, /* wheel */
+	kone_keystroke_button_9 = 0xf3, /* side button up */
+	kone_keystroke_button_8 = 0xf4 /* side button down */
+};
+
+enum kone_keystroke_actions {
+	kone_keystroke_action_press = 0,
+	kone_keystroke_action_release = 1
+};
+
+struct kone_button_info {
+	uint8_t number; /* range 1-8 */
+	uint8_t type;
+	uint8_t macro_type; /* 0 = short, 1 = overlong */
+	uint8_t macro_set_name[16]; /* can be max 15 chars long */
+	uint8_t macro_name[16]; /* can be max 15 chars long */
+	uint8_t count;
+	struct kone_keystroke keystrokes[20];
+};
+
+enum kone_button_info_types {
+	/* valid button types until firmware 1.32 */
+	kone_button_info_type_button_1 = 0x1, /* click (left mouse button) */
+	kone_button_info_type_button_2 = 0x2, /* menu (right mouse button)*/
+	kone_button_info_type_button_3 = 0x3, /* scroll (wheel) */
+	kone_button_info_type_double_click = 0x4,
+	kone_button_info_type_key = 0x5,
+	kone_button_info_type_macro = 0x6,
+	kone_button_info_type_off = 0x7,
+	/* TODO clarify function and rename */
+	kone_button_info_type_osd_xy_prescaling = 0x8,
+	kone_button_info_type_osd_dpi = 0x9,
+	kone_button_info_type_osd_profile = 0xa,
+	kone_button_info_type_button_9 = 0xb, /* ie forward */
+	kone_button_info_type_button_8 = 0xc, /* ie backward */
+	kone_button_info_type_dpi_up = 0xd, /* internal */
+	kone_button_info_type_dpi_down = 0xe, /* internal */
+	kone_button_info_type_button_7 = 0xf, /* tilt left */
+	kone_button_info_type_button_6 = 0x10, /* tilt right */
+	kone_button_info_type_profile_up = 0x11, /* internal */
+	kone_button_info_type_profile_down = 0x12, /* internal */
+	/* additional valid button types since firmware 1.38 */
+	kone_button_info_type_multimedia_open_player = 0x20,
+	kone_button_info_type_multimedia_next_track = 0x21,
+	kone_button_info_type_multimedia_prev_track = 0x22,
+	kone_button_info_type_multimedia_play_pause = 0x23,
+	kone_button_info_type_multimedia_stop = 0x24,
+	kone_button_info_type_multimedia_mute = 0x25,
+	kone_button_info_type_multimedia_volume_up = 0x26,
+	kone_button_info_type_multimedia_volume_down = 0x27
+};
+
+enum kone_button_info_numbers {
+	kone_button_top = 1,
+	kone_button_wheel_tilt_left = 2,
+	kone_button_wheel_tilt_right = 3,
+	kone_button_forward = 4,
+	kone_button_backward = 5,
+	kone_button_middle = 6,
+	kone_button_plus = 7,
+	kone_button_minus = 8,
+};
+
+struct kone_light_info {
+	uint8_t number; /* number of light 1-5 */
+	uint8_t mod;   /* 1 = on, 2 = off */
+	uint8_t red;   /* range 0x00-0xff */
+	uint8_t green; /* range 0x00-0xff */
+	uint8_t blue;  /* range 0x00-0xff */
+};
+
+struct kone_profile {
+	uint16_t size; /* always 975 */
+	uint16_t unused; /* always 0 */
+
+	/*
+	 * range 1-5
+	 * This number does not need to correspond with location where profile
+	 * saved
+	 */
+	uint8_t profile; /* range 1-5 */
+
+	uint16_t main_sensitivity; /* range 100-1000 */
+	uint8_t xy_sensitivity_enabled; /* 1 = on, 2 = off */
+	uint16_t x_sensitivity; /* range 100-1000 */
+	uint16_t y_sensitivity; /* range 100-1000 */
+	uint8_t dpi_rate; /* bit 1 = 800, ... */
+	uint8_t startup_dpi; /* range 1-6 */
+	uint8_t polling_rate; /* 1 = 125Hz, 2 = 500Hz, 3 = 1000Hz */
+	/* kone has no dcu
+	 * value is always 2 in firmwares <= 1.32 and
+	 * 1 in firmwares > 1.32
+	 */
+	uint8_t dcu_flag;
+	uint8_t light_effect_1; /* range 1-3 */
+	uint8_t light_effect_2; /* range 1-5 */
+	uint8_t light_effect_3; /* range 1-4 */
+	uint8_t light_effect_speed; /* range 0-255 */
+
+	struct kone_light_info light_infos[5];
+	/* offset is kone_button_info_numbers - 1 */
+	struct kone_button_info button_infos[8];
+
+	uint16_t checksum; /* \brief holds checksum of struct */
+};
+
+enum kone_polling_rates {
+	kone_polling_rate_125 = 1,
+	kone_polling_rate_500 = 2,
+	kone_polling_rate_1000 = 3
+};
+
+struct kone_settings {
+	uint16_t size; /* always 36 */
+	uint8_t  startup_profile; /* 1-5 */
+	uint8_t	 unknown1;
+	uint8_t  tcu; /* 0 = off, 1 = on */
+	uint8_t  unknown2[23];
+	uint8_t  calibration_data[4];
+	uint8_t  unknown3[2];
+	uint16_t checksum;
+};
+
+/*
+ * 12 byte mouse event read by interrupt_read
+ */
+struct kone_mouse_event {
+	uint8_t report_number; /* always 1 */
+	uint8_t button;
+	uint16_t x;
+	uint16_t y;
+	uint8_t wheel; /* up = 1, down = -1 */
+	uint8_t tilt; /* right = 1, left = -1 */
+	uint8_t unknown;
+	uint8_t event;
+	uint8_t value; /* press = 0, release = 1 */
+	uint8_t macro_key; /* 0 to 8 */
+};
+
+enum kone_mouse_events {
+	/* osd events are thought to be display on screen */
+	kone_mouse_event_osd_dpi = 0xa0,
+	kone_mouse_event_osd_profile = 0xb0,
+	/* TODO clarify meaning and occurence of kone_mouse_event_calibration */
+	kone_mouse_event_calibration = 0xc0,
+	kone_mouse_event_call_overlong_macro = 0xe0,
+	/* switch events notify if user changed values with mousebutton click */
+	kone_mouse_event_switch_dpi = 0xf0,
+	kone_mouse_event_switch_profile = 0xf1
+};
+
+enum kone_commands {
+	kone_command_profile = 0x5a,
+	kone_command_settings = 0x15a,
+	kone_command_firmware_version = 0x25a,
+	kone_command_weight = 0x45a,
+	kone_command_calibrate = 0x55a,
+	kone_command_confirm_write = 0x65a,
+	kone_command_firmware = 0xe5a
+};
+
+#pragma pack(pop)
+
+struct kone_device {
+	/*
+	 * Storing actual values when we get informed about changes since there
+	 * is no way of getting this information from the device on demand
+	 */
+	int actual_profile, actual_dpi;
+	/* Used for neutralizing abnormal button behaviour */
+	struct kone_mouse_event last_mouse_event;
+
+	/*
+	 * It's unlikely that multiple sysfs attributes are accessed at a time,
+	 * so only one mutex is used to secure hardware access and profiles and
+	 * settings of this struct.
+	 */
+	struct mutex kone_lock;
+
+	/*
+	 * Storing the data here reduces IO and ensures that data is available
+	 * when its needed (E.g. interrupt handler).
+	 */
+	struct kone_profile profiles[5];
+	struct kone_settings settings;
+
+	/*
+	 * firmware doesn't change unless firmware update is implemented,
+	 * so it's read only once
+	 */
+	int firmware_version;
+};
+
+#endif

drivers/hid/usbhid/hid-core.c

@@ -623,6 +623,7 @@ int usbhid_wait_io(struct hid_device *hid)
 
 	return 0;
 }
+EXPORT_SYMBOL_GPL(usbhid_wait_io);
 
 static int hid_set_idle(struct usb_device *dev, int ifnum, int report, int idle)
 {