Commit 37d6fb62 authored by Sascha Hauer's avatar Sascha Hauer

i.MX serial: do not use #ifdef CONFIG_ARCH_*

Signed-off-by: default avatarSascha Hauer <s.hauer@pengutronix.de>
parent ccc1a6f8
......@@ -67,21 +67,8 @@
#define UBIR 0xa4 /* BRM Incremental Register */
#define UBMR 0xa8 /* BRM Modulator Register */
#define UBRC 0xac /* Baud Rate Count Register */
#if defined CONFIG_ARCH_MX3 || defined CONFIG_ARCH_MX2
#define ONEMS 0xb0 /* One Millisecond register */
#define UTS 0xb4 /* UART Test Register */
#endif
#ifdef CONFIG_ARCH_MX1
#define BIPR1 0xb0 /* Incremental Preset Register 1 */
#define BIPR2 0xb4 /* Incremental Preset Register 2 */
#define BIPR3 0xb8 /* Incremental Preset Register 3 */
#define BIPR4 0xbc /* Incremental Preset Register 4 */
#define BMPR1 0xc0 /* BRM Modulator Register 1 */
#define BMPR2 0xc4 /* BRM Modulator Register 2 */
#define BMPR3 0xc8 /* BRM Modulator Register 3 */
#define BMPR4 0xcc /* BRM Modulator Register 4 */
#define UTS 0xd0 /* UART Test Register */
#endif
#define MX2_ONEMS 0xb0 /* One Millisecond register */
#define UTS (cpu_is_mx1() ? 0xd0 : 0xb4) /* UART Test Register */
/* UART Control Register Bit Fields.*/
#define URXD_CHARRDY (1<<15)
......@@ -101,12 +88,7 @@
#define UCR1_RTSDEN (1<<5) /* RTS delta interrupt enable */
#define UCR1_SNDBRK (1<<4) /* Send break */
#define UCR1_TDMAEN (1<<3) /* Transmitter ready DMA enable */
#ifdef CONFIG_ARCH_MX1
#define UCR1_UARTCLKEN (1<<2) /* UART clock enabled */
#endif
#if defined CONFIG_ARCH_MX3 || defined CONFIG_ARCH_MX2
#define UCR1_UARTCLKEN (0) /* not present on mx2/mx3 */
#endif
#define MX1_UCR1_UARTCLKEN (1<<2) /* UART clock enabled, mx1 only */
#define UCR1_DOZE (1<<1) /* Doze */
#define UCR1_UARTEN (1<<0) /* UART enabled */
#define UCR2_ESCI (1<<15) /* Escape seq interrupt enable */
......@@ -132,13 +114,9 @@
#define UCR3_RXDSEN (1<<6) /* Receive status interrupt enable */
#define UCR3_AIRINTEN (1<<5) /* Async IR wake interrupt enable */
#define UCR3_AWAKEN (1<<4) /* Async wake interrupt enable */
#ifdef CONFIG_ARCH_MX1
#define UCR3_REF25 (1<<3) /* Ref freq 25 MHz, only on mx1 */
#define UCR3_REF30 (1<<2) /* Ref Freq 30 MHz, only on mx1 */
#endif
#if defined CONFIG_ARCH_MX2 || defined CONFIG_ARCH_MX3
#define UCR3_RXDMUXSEL (1<<2) /* RXD Muxed Input Select, on mx2/mx3 */
#endif
#define MX1_UCR3_REF25 (1<<3) /* Ref freq 25 MHz, only on mx1 */
#define MX1_UCR3_REF30 (1<<2) /* Ref Freq 30 MHz, only on mx1 */
#define MX2_UCR3_RXDMUXSEL (1<<2) /* RXD Muxed Input Select, on mx2/mx3 */
#define UCR3_INVT (1<<1) /* Inverted Infrared transmission */
#define UCR3_BPEN (1<<0) /* Preset registers enable */
#define UCR4_CTSTL_32 (32<<10) /* CTS trigger level (32 chars) */
......@@ -186,12 +164,10 @@
#define UTS_SOFTRST (1<<0) /* Software reset */
/* We've been assigned a range on the "Low-density serial ports" major */
#ifdef CONFIG_ARCH_MXC
#define SERIAL_IMX_MAJOR 207
#define MINOR_START 16
#define DEV_NAME "ttymxc"
#define MAX_INTERNAL_IRQ MXC_INTERNAL_IRQS
#endif
/*
* This determines how often we check the modem status signals
......@@ -706,11 +682,11 @@ static int imx_startup(struct uart_port *port)
}
}
#if defined CONFIG_ARCH_MX2 || defined CONFIG_ARCH_MX3
temp = readl(sport->port.membase + UCR3);
temp |= UCR3_RXDMUXSEL;
writel(temp, sport->port.membase + UCR3);
#endif
if (!cpu_is_mx1()) {
temp = readl(sport->port.membase + UCR3);
temp |= MX2_UCR3_RXDMUXSEL;
writel(temp, sport->port.membase + UCR3);
}
if (USE_IRDA(sport)) {
temp = readl(sport->port.membase + UCR4);
......@@ -942,9 +918,9 @@ imx_set_termios(struct uart_port *port, struct ktermios *termios,
writel(num, sport->port.membase + UBIR);
writel(denom, sport->port.membase + UBMR);
#ifdef ONEMS
writel(sport->port.uartclk / div / 1000, sport->port.membase + ONEMS);
#endif
if (!cpu_is_mx1())
writel(sport->port.uartclk / div / 1000,
sport->port.membase + MX2_ONEMS);
writel(old_ucr1, sport->port.membase + UCR1);
......@@ -1074,17 +1050,20 @@ static void
imx_console_write(struct console *co, const char *s, unsigned int count)
{
struct imx_port *sport = imx_ports[co->index];
unsigned int old_ucr1, old_ucr2;
unsigned int old_ucr1, old_ucr2, ucr1;
/*
* First, save UCR1/2 and then disable interrupts
*/
old_ucr1 = readl(sport->port.membase + UCR1);
ucr1 = old_ucr1 = readl(sport->port.membase + UCR1);
old_ucr2 = readl(sport->port.membase + UCR2);
writel((old_ucr1 | UCR1_UARTCLKEN | UCR1_UARTEN) &
~(UCR1_TXMPTYEN | UCR1_RRDYEN | UCR1_RTSDEN),
sport->port.membase + UCR1);
if (cpu_is_mx1())
ucr1 |= MX1_UCR1_UARTCLKEN;
ucr1 |= UCR1_UARTEN;
ucr1 &= ~(UCR1_TXMPTYEN | UCR1_RRDYEN | UCR1_RTSDEN);
writel(ucr1, sport->port.membase + UCR1);
writel(old_ucr2 | UCR2_TXEN, sport->port.membase + UCR2);
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment