Merge tag 'amlogic-dt64' of...

Merge tag 'amlogic-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt64

Pull "Amlogic 64-bit DT updates for v4.14" from Kevin Hilman:

- add GPIO line names to a few boards
- MMC regulator settle time updates
- misc cleanups/fixups

* tag 'amlogic-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
  ARM64: dts: meson-gx: use stable UART bindings with correct gate clock
  ARM64: dts: meson-gxbb-nanopi-k2: Add GPIO lines names
  ARM64: dts: meson-gxl-khadas-vim: Add GPIO lines names
  ARM64: dts: meson-gxbb: p20x: add card regulator settle times
  dt-bindings: amlogic: add unstable statement
  ARM64: dts: meson-gx: Add SoC info register
  ARM64: dts: meson-gx: consistently use the GIC_SPI and IRQ type macros

Documentation/devicetree/bindings/arm/amlogic.txt

 Amlogic MesonX device tree bindings
 -------------------------------------------
 
+Work in progress statement:
+
+Device tree files and bindings applying to Amlogic SoCs and boards are
+considered "unstable". Any Amlogic device tree binding may change at
+any time. Be sure to use a device tree binary and a kernel image
+generated from the same source tree.
+
+Please refer to Documentation/devicetree/bindings/ABI.txt for a definition of a
+stable binding/ABI.
+
+---------------------------------------------------------------
+
 Boards with the Amlogic Meson6 SoC shall have the following properties:
   Required root node property:
     compatible: "amlogic,meson6"

arch/arm64/boot/dts/amlogic/meson-gx.dtsi

@@ -225,7 +225,7 @@ reset: reset-controller@4404 {
 			};
 
 			uart_A: serial@84c0 {
-				compatible = "amlogic,meson-uart";
+				compatible = "amlogic,meson-gx-uart", "amlogic,meson-uart";
 				reg = <0x0 0x84c0 0x0 0x14>;
 				interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>;
 				clocks = <&xtal>;
@@ -233,7 +233,7 @@ uart_A: serial@84c0 {
 			};
 
 			uart_B: serial@84dc {
-				compatible = "amlogic,meson-uart";
+				compatible = "amlogic,meson-gx-uart", "amlogic,meson-uart";
 				reg = <0x0 0x84dc 0x0 0x14>;
 				interrupts = <GIC_SPI 75 IRQ_TYPE_EDGE_RISING>;
 				clocks = <&xtal>;
@@ -279,7 +279,7 @@ pwm_ef: pwm@86c0 {
 			};
 
 			uart_C: serial@8700 {
-				compatible = "amlogic,meson-uart";
+				compatible = "amlogic,meson-gx-uart", "amlogic,meson-uart";
 				reg = <0x0 0x8700 0x0 0x14>;
 				interrupts = <GIC_SPI 93 IRQ_TYPE_EDGE_RISING>;
 				clocks = <&xtal>;
@@ -374,19 +374,23 @@ clkc_AO: clock-controller@040 {
 				#reset-cells = <1>;
 			};
 
+			sec_AO: ao-secure@140 {
+				compatible = "amlogic,meson-gx-ao-secure", "syscon";
+				reg = <0x0 0x140 0x0 0x140>;
+				amlogic,has-chip-id;
+			};
+
 			uart_AO: serial@4c0 {
-				compatible = "amlogic,meson-uart";
+				compatible = "amlogic,meson-gx-uart", "amlogic,meson-ao-uart", "amlogic,meson-uart";
 				reg = <0x0 0x004c0 0x0 0x14>;
 				interrupts = <GIC_SPI 193 IRQ_TYPE_EDGE_RISING>;
-				clocks = <&xtal>;
 				status = "disabled";
 			};
 
 			uart_AO_B: serial@4e0 {
-				compatible = "amlogic,meson-uart";
+				compatible = "amlogic,meson-gx-uart", "amlogic,meson-ao-uart", "amlogic,meson-uart";
 				reg = <0x0 0x004e0 0x0 0x14>;
 				interrupts = <GIC_SPI 197 IRQ_TYPE_EDGE_RISING>;
-				clocks = <&xtal>;
 				status = "disabled";
 			};
 
@@ -437,9 +441,9 @@ hiubus: hiubus@c883c000 {
 			mailbox: mailbox@404 {
 				compatible = "amlogic,meson-gx-mhu", "amlogic,meson-gxbb-mhu";
 				reg = <0 0x404 0 0x4c>;
-				interrupts = <0 208 IRQ_TYPE_EDGE_RISING>,
-					     <0 209 IRQ_TYPE_EDGE_RISING>,
-					     <0 210 IRQ_TYPE_EDGE_RISING>;
+				interrupts = <GIC_SPI 208 IRQ_TYPE_EDGE_RISING>,
+					     <GIC_SPI 209 IRQ_TYPE_EDGE_RISING>,
+					     <GIC_SPI 210 IRQ_TYPE_EDGE_RISING>;
 				#mbox-cells = <1>;
 			};
 		};
@@ -448,7 +452,7 @@ ethmac: ethernet@c9410000 {
 			compatible = "amlogic,meson-gx-dwmac", "amlogic,meson-gxbb-dwmac", "snps,dwmac";
 			reg = <0x0 0xc9410000 0x0 0x10000
 			       0x0 0xc8834540 0x0 0x4>;
-			interrupts = <0 8 1>;
+			interrupts = <GIC_SPI 8 IRQ_TYPE_EDGE_RISING>;
 			interrupt-names = "macirq";
 			status = "disabled";
 		};

arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts

@@ -175,6 +175,64 @@ &ir {
 	pinctrl-names = "default";
 };
 
+&pinctrl_aobus {
+	gpio-line-names = "UART TX", "UART RX", "Power Control", "Power Key In",
+			  "VCCK En", "CON1 Header Pin31",
+			  "I2S Header Pin6", "IR In", "I2S Header Pin7",
+			  "I2S Header Pin3", "I2S Header Pin4",
+			  "I2S Header Pin5", "HDMI CEC", "SYS LED";
+};
+
+&pinctrl_periphs {
+	gpio-line-names = /* Bank GPIOZ */
+			  "Eth MDIO", "Eth MDC", "Eth RGMII RX Clk",
+			  "Eth RX DV", "Eth RX D0", "Eth RX D1", "Eth RX D2",
+			  "Eth RX D3", "Eth RGMII TX Clk", "Eth TX En",
+			  "Eth TX D0", "Eth TX D1", "Eth TX D2", "Eth TX D3",
+			  "Eth PHY nRESET", "Eth PHY Intc",
+			  /* Bank GPIOH */
+			  "HDMI HPD", "HDMI DDC SDA", "HDMI DDC SCL",
+			  "CON1 Header Pin33",
+			  /* Bank BOOT */
+			  "eMMC D0", "eMMC D1", "eMMC D2", "eMMC D3", "eMMC D4",
+			  "eMMC D5", "eMMC D6", "eMMC D7", "eMMC Clk",
+			  "eMMC Reset", "eMMC CMD",
+			  "", "", "", "", "eMMC DS",
+			  "", "",
+			  /* Bank CARD */
+			  "SDCard D1", "SDCard D0", "SDCard CLK", "SDCard CMD",
+			  "SDCard D3", "SDCard D2", "SDCard Det",
+			  /* Bank GPIODV */
+			  "", "", "", "", "", "", "", "", "", "", "", "", "",
+			  "", "", "", "", "", "", "", "", "", "", "",
+			  "I2C A SDA", "I2C A SCK", "I2C B SDA", "I2C B SCK",
+			  "VDDEE Regulator", "VCCK Regulator",
+			  /* Bank GPIOY */
+			  "CON1 Header Pin7", "CON1 Header Pin11",
+			  "CON1 Header Pin13", "CON1 Header Pin15",
+			  "CON1 Header Pin18", "CON1 Header Pin19",
+			  "CON1 Header Pin22", "CON1 Header Pin21",
+			  "CON1 Header Pin24", "CON1 Header Pin23",
+			  "CON1 Header Pin26", "CON1 Header Pin29",
+			  "CON1 Header Pin32", "CON1 Header Pin8",
+			  "CON1 Header Pin10", "CON1 Header Pin16",
+			  "CON1 Header Pin12",
+			  /* Bank GPIOX */
+			  "WIFI SDIO D0", "WIFI SDIO D1", "WIFI SDIO D2",
+			  "WIFI SDIO D3", "WIFI SDIO CLK", "WIFI SDIO CMD",
+			  "WIFI Power Enable", "WIFI WAKE HOST",
+			  "Bluetooth PCM DOUT", "Bluetooth PCM DIN",
+			  "Bluetooth PCM SYNC", "Bluetooth PCM CLK",
+			  "Bluetooth UART TX", "Bluetooth UART RX",
+			  "Bluetooth UART CTS", "Bluetooth UART RTS",
+			  "", "", "", "WIFI 32K", "Bluetooth Enable",
+			  "Bluetooth WAKE HOST",
+			  /* Bank GPIOCLK */
+			  "", "CON1 Header Pin35", "", "",
+			  /* GPIO_TEST_N */
+			  "";
+};
+
 &pwm_ef {
 	status = "okay";
 	pinctrl-0 = <&pwm_e_pins>;

arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi

@@ -84,6 +84,9 @@ vddio_card: gpio-regulator {
 		/* Based on P200 schematics, signal CARD_1.8V/3.3V_CTR */
 		states = <1800000 0
 			  3300000 1>;
+
+		regulator-settling-time-up-us = <10000>;
+		regulator-settling-time-down-us = <150000>;
 	};
 
 	vddio_boot: regulator-vddio_boot {

arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi

@@ -682,6 +682,31 @@ &spifc {
 	clocks = <&clkc CLKID_SPI>;
 };
 
+&uart_A {
+	clocks = <&xtal>, <&clkc CLKID_UART0>, <&xtal>;
+	clock-names = "xtal", "pclk", "baud";
+};
+
+&uart_AO {
+	clocks = <&xtal>, <&clkc CLKID_CLK81>, <&xtal>;
+	clock-names = "xtal", "pclk", "baud";
+};
+
+&uart_AO_B {
+	clocks = <&xtal>, <&clkc CLKID_CLK81>, <&xtal>;
+	clock-names = "xtal", "pclk", "baud";
+};
+
+&uart_B {
+	clocks = <&xtal>, <&clkc CLKID_UART1>, <&xtal>;
+	clock-names = "xtal", "core", "baud";
+};
+
+&uart_C {
+	clocks = <&xtal>, <&clkc CLKID_UART2>, <&xtal>;
+	clock-names = "xtal", "core", "baud";
+};
+
 &vpu {
 	compatible = "amlogic,meson-gxbb-vpu", "amlogic,meson-gx-vpu";
 };

arch/arm64/boot/dts/amlogic/meson-gxl-s905x-khadas-vim.dts

@@ -105,6 +105,62 @@ &ir {
 	linux,rc-map-name = "rc-geekbox";
 };
 
+&pinctrl_aobus {
+	gpio-line-names = "UART TX",
+			  "UART RX",
+			  "Power Key In",
+			  "J9 Header Pin35",
+			  "J9 Header Pin16",
+			  "J9 Header Pin15",
+			  "J9 Header Pin33",
+			  "IR In",
+			  "HDMI CEC",
+			  "SYS LED";
+};
+
+&pinctrl_periphs {
+	gpio-line-names = /* Bank GPIOZ */
+			  "", "", "", "", "", "", "",
+			  "", "", "", "", "", "", "",
+			  "Power OFF",
+			  "VCCK Enable",
+			  /* Bank GPIOH */
+			  "HDMI HPD", "HDMI SDA", "HDMI SCL",
+			  "HDMI_5V_EN", "SPDIF",
+			  "J9 Header Pin37",
+			  "J9 Header Pin30",
+			  "J9 Header Pin29",
+			  "J9 Header Pin32",
+			  "J9 Header Pin31",
+			  /* Bank BOOT */
+			  "eMMC D0", "eMMC D1", "eMMC D2", "eMMC D3",
+			  "eMMC D4", "eMMC D5", "eMMC D6", "eMMC D7",
+			  "eMMC Clk", "eMMC Reset", "eMMC CMD",
+			  "", "BOOT_MODE", "", "", "eMMC Data Strobe",
+			  /* Bank CARD */
+			  "SDCard D1", "SDCard D0", "SDCard CLK", "SDCard CMD",
+			  "SDCard D3", "SDCard D2", "SDCard Det",
+			  /* Bank GPIODV */
+			  "", "", "", "", "", "", "", "", "", "", "", "",
+			  "", "", "", "", "", "", "", "", "", "", "", "",
+			  "I2C A SDA", "I2C A SCK", "I2C B SDA", "I2C B SCK",
+			  "VCCK Regulator", "VDDEE Regulator",
+			  /* Bank GPIOX */
+			  "WIFI SDIO D0", "WIFI SDIO D1", "WIFI SDIO D2",
+			  "WIFI SDIO D3", "WIFI SDIO CLK", "WIFI SDIO CMD",
+			  "WIFI Power Enable", "WIFI WAKE HOST",
+			  "Bluetooth PCM DOUT", "Bluetooth PCM DIN",
+			  "Bluetooth PCM SYNC", "Bluetooth PCM CLK",
+			  "Bluetooth UART TX", "Bluetooth UART RX",
+			  "Bluetooth UART CTS", "Bluetooth UART RTS",
+			  "WIFI 32K", "Bluetooth Enable",
+			  "Bluetooth WAKE HOST",
+			  /* Bank GPIOCLK */
+			  "", "J9 Header Pin39",
+			  /* GPIO_TEST_N */
+			  "";
+};
+
 &pwm_AO_ab {
 	status = "okay";
 	pinctrl-0 = <&pwm_ao_a_3_pins>, <&pwm_ao_b_pins>;

arch/arm64/boot/dts/amlogic/meson-gxl.dtsi

@@ -623,6 +623,31 @@ &spifc {
 	clocks = <&clkc CLKID_SPI>;
 };
 
+&uart_A {
+	clocks = <&xtal>, <&clkc CLKID_UART0>, <&xtal>;
+	clock-names = "xtal", "core", "baud";
+};
+
+&uart_AO {
+	clocks = <&xtal>, <&clkc CLKID_CLK81>, <&xtal>;
+	clock-names = "xtal", "pclk", "baud";
+};
+
+&uart_AO_B {
+	clocks = <&xtal>, <&clkc CLKID_CLK81>, <&xtal>;
+	clock-names = "xtal", "pclk", "baud";
+};
+
+&uart_B {
+	clocks = <&xtal>, <&clkc CLKID_UART1>, <&xtal>;
+	clock-names = "xtal", "core", "baud";
+};
+
+&uart_C {
+	clocks = <&xtal>, <&clkc CLKID_UART2>, <&xtal>;
+	clock-names = "xtal", "core", "baud";
+};
+
 &vpu {
 	compatible = "amlogic,meson-gxl-vpu", "amlogic,meson-gx-vpu";
 };