leds: triggers: don't depend on LEDS_TRIGGERS twice

All the triggers are defined in a big if LEDS_TRIGGERS...endif block.
So there is no need to let each driver depend on LEDS_TRIGGERS explicitly
once more.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>

drivers/leds/trigger/Kconfig

@@ -10,7 +10,6 @@ if LEDS_TRIGGERS
 
 config LEDS_TRIGGER_TIMER
 	tristate "LED Timer Trigger"
-	depends on LEDS_TRIGGERS
 	help
 	  This allows LEDs to be controlled by a programmable timer
 	  via sysfs. Some LED hardware can be programmed to start
@@ -21,7 +20,6 @@ config LEDS_TRIGGER_TIMER
 
 config LEDS_TRIGGER_ONESHOT
 	tristate "LED One-shot Trigger"
-	depends on LEDS_TRIGGERS
 	help
 	  This allows LEDs to blink in one-shot pulses with parameters
 	  controlled via sysfs.  It's useful to notify the user on
@@ -36,7 +34,6 @@ config LEDS_TRIGGER_ONESHOT
 config LEDS_TRIGGER_DISK
 	bool "LED Disk Trigger"
 	depends on IDE_GD_ATA || ATA
-	depends on LEDS_TRIGGERS
 	help
 	  This allows LEDs to be controlled by disk activity.
 	  If unsure, say Y.
@@ -44,14 +41,12 @@ config LEDS_TRIGGER_DISK
 config LEDS_TRIGGER_MTD
 	bool "LED MTD (NAND/NOR) Trigger"
 	depends on MTD
-	depends on LEDS_TRIGGERS
 	help
 	  This allows LEDs to be controlled by MTD activity.
 	  If unsure, say N.
 
 config LEDS_TRIGGER_HEARTBEAT
 	tristate "LED Heartbeat Trigger"
-	depends on LEDS_TRIGGERS
 	help
 	  This allows LEDs to be controlled by a CPU load average.
 	  The flash frequency is a hyperbolic function of the 1-minute
@@ -60,7 +55,6 @@ config LEDS_TRIGGER_HEARTBEAT
 
 config LEDS_TRIGGER_BACKLIGHT
 	tristate "LED backlight Trigger"
-	depends on LEDS_TRIGGERS
 	help
 	  This allows LEDs to be controlled as a backlight device: they
 	  turn off and on when the display is blanked and unblanked.
@@ -69,7 +63,6 @@ config LEDS_TRIGGER_BACKLIGHT
 
 config LEDS_TRIGGER_CPU
 	bool "LED CPU Trigger"
-	depends on LEDS_TRIGGERS
 	help
 	  This allows LEDs to be controlled by active CPUs. This shows
 	  the active CPUs across an array of LEDs so you can see which
@@ -79,7 +72,6 @@ config LEDS_TRIGGER_CPU
 
 config LEDS_TRIGGER_ACTIVITY
 	tristate "LED activity Trigger"
-	depends on LEDS_TRIGGERS
 	help
 	  This allows LEDs to be controlled by an immediate CPU usage.
 	  The flash frequency and duty cycle varies from faint flashes to
@@ -88,7 +80,6 @@ config LEDS_TRIGGER_ACTIVITY
 
 config LEDS_TRIGGER_GPIO
 	tristate "LED GPIO Trigger"
-	depends on LEDS_TRIGGERS
 	depends on GPIOLIB || COMPILE_TEST
 	help
 	  This allows LEDs to be controlled by gpio events. It's good
@@ -101,7 +92,6 @@ config LEDS_TRIGGER_GPIO
 
 config LEDS_TRIGGER_DEFAULT_ON
 	tristate "LED Default ON Trigger"
-	depends on LEDS_TRIGGERS
 	help
 	  This allows LEDs to be initialised in the ON state.
 	  If unsure, say Y.
@@ -111,7 +101,6 @@ comment "iptables trigger is under Netfilter config (LED target)"
 
 config LEDS_TRIGGER_TRANSIENT
 	tristate "LED Transient Trigger"
-	depends on LEDS_TRIGGERS
 	help
 	  This allows one time activation of a transient state on
 	  GPIO/PWM based hardware.
@@ -119,7 +108,6 @@ config LEDS_TRIGGER_TRANSIENT
 
 config LEDS_TRIGGER_CAMERA
 	tristate "LED Camera Flash/Torch Trigger"
-	depends on LEDS_TRIGGERS
 	help
 	  This allows LEDs to be controlled as a camera flash/torch device.
 	  This enables direct flash/torch on/off by the driver, kernel space.
@@ -127,7 +115,6 @@ config LEDS_TRIGGER_CAMERA
 
 config LEDS_TRIGGER_PANIC
 	bool "LED Panic Trigger"
-	depends on LEDS_TRIGGERS
 	help
 	  This allows LEDs to be configured to blink on a kernel panic.
 	  Enabling this option will allow to mark certain LEDs as panic indicators,
@@ -137,7 +124,7 @@ config LEDS_TRIGGER_PANIC
 
 config LEDS_TRIGGER_NETDEV
 	tristate "LED Netdev Trigger"
-	depends on NET && LEDS_TRIGGERS
+	depends on NET
 	help
 	  This allows LEDs to be controlled by network device activity.
 	  If unsure, say Y.