net: hns: Separate C22 and C45 transactions

The hns MDIO bus driver can perform both C22 and C45 transfers.
Create separate functions for each and register the C45 versions using
the new API calls where appropriate.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

drivers/net/ethernet/hisilicon/hns_mdio.c

@@ -206,7 +206,7 @@ static void hns_mdio_cmd_write(struct hns_mdio_device *mdio_dev,
 }
 
 /**
- * hns_mdio_write - access phy register
+ * hns_mdio_write_c22 - access phy register
  * @bus: mdio bus
  * @phy_id: phy id
  * @regnum: register num
@@ -214,21 +214,19 @@ static void hns_mdio_cmd_write(struct hns_mdio_device *mdio_dev,
  *
  * Return 0 on success, negative on failure
  */
-static int hns_mdio_write(struct mii_bus *bus,
-			  int phy_id, int regnum, u16 data)
+static int hns_mdio_write_c22(struct mii_bus *bus,
+			      int phy_id, int regnum, u16 data)
 {
-	int ret;
 	struct hns_mdio_device *mdio_dev = (struct hns_mdio_device *)bus->priv;
-	u8 devad = ((regnum >> 16) & 0x1f);
-	u8 is_c45 = !!(regnum & MII_ADDR_C45);
 	u16 reg = (u16)(regnum & 0xffff);
-	u8 op;
 	u16 cmd_reg_cfg;
+	int ret;
+	u8 op;
 
 	dev_dbg(&bus->dev, "mdio write %s,base is %p\n",
 		bus->id, mdio_dev->vbase);
-	dev_dbg(&bus->dev, "phy id=%d, is_c45=%d, devad=%d, reg=%#x, write data=%d\n",
-		phy_id, is_c45, devad, reg, data);
+	dev_dbg(&bus->dev, "phy id=%d, reg=%#x, write data=%d\n",
+		phy_id, reg, data);
 
 	/* wait for ready */
 	ret = hns_mdio_wait_ready(bus);
@@ -237,58 +235,91 @@ static int hns_mdio_write(struct mii_bus *bus,
 		return ret;
 	}
 
-	if (!is_c45) {
-		cmd_reg_cfg = reg;
-		op = MDIO_C22_WRITE;
-	} else {
-		/* config the cmd-reg to write addr*/
-		MDIO_SET_REG_FIELD(mdio_dev, MDIO_ADDR_REG, MDIO_ADDR_DATA_M,
-				   MDIO_ADDR_DATA_S, reg);
+	cmd_reg_cfg = reg;
+	op = MDIO_C22_WRITE;
 
-		hns_mdio_cmd_write(mdio_dev, is_c45,
-				   MDIO_C45_WRITE_ADDR, phy_id, devad);
+	MDIO_SET_REG_FIELD(mdio_dev, MDIO_WDATA_REG, MDIO_WDATA_DATA_M,
+			   MDIO_WDATA_DATA_S, data);
 
-		/* check for read or write opt is finished */
-		ret = hns_mdio_wait_ready(bus);
-		if (ret) {
-			dev_err(&bus->dev, "MDIO bus is busy\n");
-			return ret;
-		}
+	hns_mdio_cmd_write(mdio_dev, false, op, phy_id, cmd_reg_cfg);
+
+	return 0;
+}
+
+/**
+ * hns_mdio_write_c45 - access phy register
+ * @bus: mdio bus
+ * @phy_id: phy id
+ * @devad: device address to read
+ * @regnum: register num
+ * @data: register value
+ *
+ * Return 0 on success, negative on failure
+ */
+static int hns_mdio_write_c45(struct mii_bus *bus, int phy_id, int devad,
+			      int regnum, u16 data)
+{
+	struct hns_mdio_device *mdio_dev = (struct hns_mdio_device *)bus->priv;
+	u16 reg = (u16)(regnum & 0xffff);
+	u16 cmd_reg_cfg;
+	int ret;
+	u8 op;
+
+	dev_dbg(&bus->dev, "mdio write %s,base is %p\n",
+		bus->id, mdio_dev->vbase);
+	dev_dbg(&bus->dev, "phy id=%d, devad=%d, reg=%#x, write data=%d\n",
+		phy_id, devad, reg, data);
+
+	/* wait for ready */
+	ret = hns_mdio_wait_ready(bus);
+	if (ret) {
+		dev_err(&bus->dev, "MDIO bus is busy\n");
+		return ret;
+	}
+
+	/* config the cmd-reg to write addr*/
+	MDIO_SET_REG_FIELD(mdio_dev, MDIO_ADDR_REG, MDIO_ADDR_DATA_M,
+			   MDIO_ADDR_DATA_S, reg);
 
-		/* config the data needed writing */
-		cmd_reg_cfg = devad;
-		op = MDIO_C45_WRITE_DATA;
+	hns_mdio_cmd_write(mdio_dev, true, MDIO_C45_WRITE_ADDR, phy_id, devad);
+
+	/* check for read or write opt is finished */
+	ret = hns_mdio_wait_ready(bus);
+	if (ret) {
+		dev_err(&bus->dev, "MDIO bus is busy\n");
+		return ret;
 	}
 
+	/* config the data needed writing */
+	cmd_reg_cfg = devad;
+	op = MDIO_C45_WRITE_DATA;
+
 	MDIO_SET_REG_FIELD(mdio_dev, MDIO_WDATA_REG, MDIO_WDATA_DATA_M,
 			   MDIO_WDATA_DATA_S, data);
 
-	hns_mdio_cmd_write(mdio_dev, is_c45, op, phy_id, cmd_reg_cfg);
+	hns_mdio_cmd_write(mdio_dev, true, op, phy_id, cmd_reg_cfg);
 
 	return 0;
 }
 
 /**
- * hns_mdio_read - access phy register
+ * hns_mdio_read_c22 - access phy register
  * @bus: mdio bus
  * @phy_id: phy id
  * @regnum: register num
  *
  * Return phy register value
  */
-static int hns_mdio_read(struct mii_bus *bus, int phy_id, int regnum)
+static int hns_mdio_read_c22(struct mii_bus *bus, int phy_id, int regnum)
 {
-	int ret;
-	u16 reg_val;
-	u8 devad = ((regnum >> 16) & 0x1f);
-	u8 is_c45 = !!(regnum & MII_ADDR_C45);
-	u16 reg = (u16)(regnum & 0xffff);
 	struct hns_mdio_device *mdio_dev = (struct hns_mdio_device *)bus->priv;
+	u16 reg = (u16)(regnum & 0xffff);
+	u16 reg_val;
+	int ret;
 
 	dev_dbg(&bus->dev, "mdio read %s,base is %p\n",
 		bus->id, mdio_dev->vbase);
-	dev_dbg(&bus->dev, "phy id=%d, is_c45=%d, devad=%d, reg=%#x!\n",
-		phy_id, is_c45, devad, reg);
+	dev_dbg(&bus->dev, "phy id=%d, reg=%#x!\n", phy_id, reg);
 
 	/* Step 1: wait for ready */
 	ret = hns_mdio_wait_ready(bus);
@@ -297,29 +328,74 @@ static int hns_mdio_read(struct mii_bus *bus, int phy_id, int regnum)
 		return ret;
 	}
 
-	if (!is_c45) {
-		hns_mdio_cmd_write(mdio_dev, is_c45,
-				   MDIO_C22_READ, phy_id, reg);
-	} else {
-		MDIO_SET_REG_FIELD(mdio_dev, MDIO_ADDR_REG, MDIO_ADDR_DATA_M,
-				   MDIO_ADDR_DATA_S, reg);
+	hns_mdio_cmd_write(mdio_dev, false, MDIO_C22_READ, phy_id, reg);
 
-		/* Step 2; config the cmd-reg to write addr*/
-		hns_mdio_cmd_write(mdio_dev, is_c45,
-				   MDIO_C45_WRITE_ADDR, phy_id, devad);
+	/* Step 2: waiting for MDIO_COMMAND_REG 's mdio_start==0,*/
+	/* check for read or write opt is finished */
+	ret = hns_mdio_wait_ready(bus);
+	if (ret) {
+		dev_err(&bus->dev, "MDIO bus is busy\n");
+		return ret;
+	}
 
-		/* Step 3: check for read or write opt is finished */
-		ret = hns_mdio_wait_ready(bus);
-		if (ret) {
-			dev_err(&bus->dev, "MDIO bus is busy\n");
-			return ret;
-		}
+	reg_val = MDIO_GET_REG_BIT(mdio_dev, MDIO_STA_REG, MDIO_STATE_STA_B);
+	if (reg_val) {
+		dev_err(&bus->dev, " ERROR! MDIO Read failed!\n");
+		return -EBUSY;
+	}
 
-		hns_mdio_cmd_write(mdio_dev, is_c45,
-				   MDIO_C45_READ, phy_id, devad);
+	/* Step 3; get out data*/
+	reg_val = (u16)MDIO_GET_REG_FIELD(mdio_dev, MDIO_RDATA_REG,
+					  MDIO_RDATA_DATA_M, MDIO_RDATA_DATA_S);
+
+	return reg_val;
+}
+
+/**
+ * hns_mdio_read_c45 - access phy register
+ * @bus: mdio bus
+ * @phy_id: phy id
+ * @devad: device address to read
+ * @regnum: register num
+ *
+ * Return phy register value
+ */
+static int hns_mdio_read_c45(struct mii_bus *bus, int phy_id, int devad,
+			     int regnum)
+{
+	struct hns_mdio_device *mdio_dev = (struct hns_mdio_device *)bus->priv;
+	u16 reg = (u16)(regnum & 0xffff);
+	u16 reg_val;
+	int ret;
+
+	dev_dbg(&bus->dev, "mdio read %s,base is %p\n",
+		bus->id, mdio_dev->vbase);
+	dev_dbg(&bus->dev, "phy id=%d, devad=%d, reg=%#x!\n",
+		phy_id, devad, reg);
+
+	/* Step 1: wait for ready */
+	ret = hns_mdio_wait_ready(bus);
+	if (ret) {
+		dev_err(&bus->dev, "MDIO bus is busy\n");
+		return ret;
+	}
+
+	MDIO_SET_REG_FIELD(mdio_dev, MDIO_ADDR_REG, MDIO_ADDR_DATA_M,
+			   MDIO_ADDR_DATA_S, reg);
+
+	/* Step 2; config the cmd-reg to write addr*/
+	hns_mdio_cmd_write(mdio_dev, true, MDIO_C45_WRITE_ADDR, phy_id, devad);
+
+	/* Step 3: check for read or write opt is finished */
+	ret = hns_mdio_wait_ready(bus);
+	if (ret) {
+		dev_err(&bus->dev, "MDIO bus is busy\n");
+		return ret;
 	}
 
-	/* Step 5: waiting for MDIO_COMMAND_REG's mdio_start==0,*/
+	hns_mdio_cmd_write(mdio_dev, true, MDIO_C45_READ, phy_id, devad);
+
+	/* Step 5: waiting for MDIO_COMMAND_REG 's mdio_start==0,*/
 	/* check for read or write opt is finished */
 	ret = hns_mdio_wait_ready(bus);
 	if (ret) {
@@ -438,8 +514,10 @@ static int hns_mdio_probe(struct platform_device *pdev)
 	}
 
 	new_bus->name = MDIO_BUS_NAME;
-	new_bus->read = hns_mdio_read;
-	new_bus->write = hns_mdio_write;
+	new_bus->read = hns_mdio_read_c22;
+	new_bus->write = hns_mdio_write_c22;
+	new_bus->read_c45 = hns_mdio_read_c45;
+	new_bus->write_c45 = hns_mdio_write_c45;
 	new_bus->reset = hns_mdio_reset;
 	new_bus->priv = mdio_dev;
 	new_bus->parent = &pdev->dev;