[Bluetooth] Send HCI_Reset for some Broadcom dongles

This patch introduces a quirk flag for sending the HCI_Reset command. In
general the HCI_Reset is not needed, but some Broadcom dongles uses this
reset command to switch from HID to HCI mode. And it is not safe to send
the HCI_Reset to every Bluetooth device, because the CSR firmware prior
HCI 12.x will reset the host transport and this is wrong according to the
Bluetooth specification.

drivers/bluetooth/hci_usb.c

@@ -31,7 +31,7 @@
  *
  * $Id: hci_usb.c,v 1.8 2002/07/18 17:23:09 maxk Exp $    
  */
-#define VERSION "2.4"
+#define VERSION "2.5"
 
 #include <linux/config.h>
 #include <linux/module.h>
@@ -70,12 +70,6 @@
 static struct usb_driver hci_usb_driver; 
 
 static struct usb_device_id bluetooth_ids[] = {
-	/* Broadcom BCM2033 without firmware */
-	{ USB_DEVICE(0x0a5c, 0x2033), .driver_info = HCI_IGNORE },
-
-	/* Digianswer device */
-	{ USB_DEVICE(0x08fd, 0x0001), .driver_info = HCI_DIGIANSWER },
-
 	/* Generic Bluetooth USB device */
 	{ USB_DEVICE_INFO(HCI_DEV_CLASS, HCI_DEV_SUBCLASS, HCI_DEV_PROTOCOL) },
 
@@ -93,6 +87,19 @@ static struct usb_device_id bluetooth_ids[] = {
 
 MODULE_DEVICE_TABLE (usb, bluetooth_ids);
 
+static struct usb_device_id blacklist_ids[] = {
+	/* Broadcom BCM2033 without firmware */
+	{ USB_DEVICE(0x0a5c, 0x2033), .driver_info = HCI_IGNORE },
+
+	/* Broadcom BCM2035 */
+	{ USB_DEVICE(0x0a5c, 0x200a), .driver_info = HCI_RESET },
+
+	/* Digianswer device */
+	{ USB_DEVICE(0x08fd, 0x0001), .driver_info = HCI_DIGIANSWER },
+
+	{ }     /* Terminating entry */
+};
+
 struct _urb *_urb_alloc(int isoc, int gfp)
 {
 	struct _urb *_urb = kmalloc(sizeof(struct _urb) +
@@ -644,7 +651,7 @@ static inline int __recv_frame(struct hci_usb *husb, int type, void *data, int c
 #endif
 			}
 			BT_DBG("new packet len %d", len);
-				
+
 			skb = bt_skb_alloc(len, GFP_ATOMIC);
 			if (!skb) {
 				BT_ERR("%s no memory for the packet", husb->hdev->name);
@@ -790,6 +797,13 @@ int hci_usb_probe(struct usb_interface *intf, const struct usb_device_id *id)
 
 	BT_DBG("udev %p ifnum %d", udev, ifnum);
 
+	if (!id->driver_info) {
+		const struct usb_device_id *match;
+		match = usb_match_id(intf, blacklist_ids);
+		if (match)
+			id = match;
+	}
+
 	iface = udev->actconfig->interface[0];
 
 	if (id->driver_info & HCI_IGNORE)
@@ -928,6 +942,9 @@ int hci_usb_probe(struct usb_interface *intf, const struct usb_device_id *id)
 
 	hdev->owner = THIS_MODULE;
 
+	if (id->driver_info & HCI_RESET)
+		set_bit(HCI_QUIRK_RESET_ON_INIT, &hdev->quirks);
+
 	if (hci_register_dev(hdev) < 0) {
 		BT_ERR("Can't register HCI device");
 		hci_free_dev(hdev);
@@ -994,6 +1011,6 @@ void hci_usb_cleanup(void)
 module_init(hci_usb_init);
 module_exit(hci_usb_cleanup);
 
-MODULE_AUTHOR("Maxim Krasnyansky <maxk@qualcomm.com>");
+MODULE_AUTHOR("Maxim Krasnyansky <maxk@qualcomm.com>, Marcel Holtmann <marcel@holtmann.org>");
 MODULE_DESCRIPTION("Bluetooth HCI USB driver ver " VERSION);
 MODULE_LICENSE("GPL");

drivers/bluetooth/hci_usb.h

@@ -38,7 +38,8 @@
 #define HCI_DIGI_REQ	     0x40
 
 #define HCI_IGNORE           0x01
-#define HCI_DIGIANSWER       0x02
+#define HCI_RESET            0x02
+#define HCI_DIGIANSWER       0x04
 
 #define HCI_MAX_IFACE_NUM	3 
 

include/net/bluetooth/hci.h

@@ -50,6 +50,11 @@
 #define HCI_RS232 	4
 #define HCI_PCI		5
 
+/* HCI device quirks */
+enum {
+	HCI_QUIRK_RESET_ON_INIT
+};
+
 /* HCI device flags */
 enum {
 	HCI_UP,

include/net/bluetooth/hci_core.h

@@ -77,6 +77,8 @@ struct hci_dev {
 	__u16		link_policy;
 	__u16		link_mode;
 
+	unsigned long	quirks;
+
 	atomic_t 	cmd_cnt;
 	unsigned int 	acl_cnt;
 	unsigned int 	sco_cnt;

net/bluetooth/hci_core.c

@@ -189,6 +189,10 @@ static void hci_init_req(struct hci_dev *hdev, unsigned long opt)
 
 	/* Mandatory initialization */
 
+	/* Reset */
+	if (test_bit(HCI_QUIRK_RESET_ON_INIT, &hdev->quirks))
+			hci_send_cmd(hdev, OGF_HOST_CTL, OCF_RESET, 0, NULL);
+
 	/* Read Local Supported Features */
 	hci_send_cmd(hdev, OGF_INFO_PARAM, OCF_READ_LOCAL_FEATURES, 0, NULL);