ide: remove CONFIG_BLK_DEV_IDE config option (take 2)

Because hd.c was moved to drivers/block/ this config option
is superfluous now and may be removed.

v2:
Fix drivers/ide/Makefile (noticed by Adrian Bunk).

Cc: Adrian Bunk <bunk@kernel.org>
Signed-off-by: default avatarBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
parent baf08f0b
......@@ -54,38 +54,6 @@ menuconfig IDE
if IDE
config BLK_DEV_IDE
tristate "Enhanced IDE/MFM/RLL disk/cdrom/tape/floppy support"
---help---
If you say Y here, you will use the full-featured IDE driver to
control up to ten ATA/IDE interfaces, each being able to serve a
"master" and a "slave" device, for a total of up to twenty ATA/IDE
disk/cdrom/tape/floppy drives.
Useful information about large (>540 MB) IDE disks, multiple
interfaces, what to do if ATA/IDE devices are not automatically
detected, sound card ATA/IDE ports, module support, and other
topics, is contained in <file:Documentation/ide/ide.txt>. For detailed
information about hard drives, consult the Disk-HOWTO and the
Multi-Disk-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
To fine-tune ATA/IDE drive/interface parameters for improved
performance, look for the hdparm package at
<ftp://ibiblio.org/pub/Linux/system/hardware/>.
To compile this driver as a module, choose M here and read
<file:Documentation/ide/ide.txt>. The module will be called ide-mod.
Do not compile this driver as a module if your root file system (the
one containing the directory /) is located on an IDE device.
If you have one or more IDE drives, say Y or M here. If your system
has no IDE drives, or if memory requirements are really tight, you
could say N here, and select the "Old hard disk driver" below
instead to save about 13 KB of memory in the kernel.
if BLK_DEV_IDE
comment "Please see Documentation/ide/ide.txt for help/info on IDE drives"
config IDE_TIMINGS
......@@ -348,7 +316,7 @@ config BLK_DEV_IDEPCI
config IDEPCI_PCIBUS_ORDER
bool "Probe IDE PCI devices in the PCI bus order (DEPRECATED)"
depends on BLK_DEV_IDE=y && BLK_DEV_IDEPCI
depends on IDE=y && BLK_DEV_IDEPCI
default y
help
Probe IDE PCI devices in the order in which they appear on the
......@@ -729,7 +697,7 @@ endif
config BLK_DEV_IDE_PMAC
tristate "PowerMac on-board IDE support"
depends on PPC_PMAC && IDE=y && BLK_DEV_IDE=y
depends on PPC_PMAC && IDE=y
select IDE_TIMINGS
help
This driver provides support for the on-board IDE controller on
......@@ -963,6 +931,4 @@ config BLK_DEV_IDEDMA
def_bool BLK_DEV_IDEDMA_SFF || BLK_DEV_IDEDMA_PMAC || \
BLK_DEV_IDEDMA_ICS || BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
endif
endif # IDE
......@@ -15,14 +15,14 @@ ide-core-$(CONFIG_BLK_DEV_IDEDMA) += ide-dma.o
ide-core-$(CONFIG_IDE_PROC_FS) += ide-proc.o
ide-core-$(CONFIG_BLK_DEV_IDEACPI) += ide-acpi.o
obj-$(CONFIG_BLK_DEV_IDE) += ide-core.o
obj-$(CONFIG_IDE) += ide-core.o
ifeq ($(CONFIG_IDE_ARM), y)
ide-arm-core-y += arm/ide_arm.o
obj-y += ide-arm-core.o
endif
obj-$(CONFIG_BLK_DEV_IDE) += legacy/ pci/
obj-$(CONFIG_IDE) += legacy/ pci/
obj-$(CONFIG_IDEPCI_PCIBUS_ORDER) += ide-scan-pci.o
......@@ -31,7 +31,7 @@ ifeq ($(CONFIG_BLK_DEV_CMD640), y)
obj-y += cmd640-core.o
endif
obj-$(CONFIG_BLK_DEV_IDE) += ppc/
obj-$(CONFIG_IDE) += ppc/
obj-$(CONFIG_IDE_H8300) += h8300/
obj-$(CONFIG_IDE_GENERIC) += ide-generic.o
obj-$(CONFIG_BLK_DEV_IDEPNP) += ide-pnp.o
......@@ -54,4 +54,4 @@ ifeq ($(CONFIG_BLK_DEV_PLATFORM), y)
obj-y += ide-platform-core.o
endif
obj-$(CONFIG_BLK_DEV_IDE) += arm/ mips/
obj-$(CONFIG_IDE) += arm/ mips/
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment