arm64: dts: qcom: sc7180: align MPSS PAS node with bindings

The SC7180 MPSS/MSS remote processor can be brought to life using two
different bindings:
1. qcom,sc7180-mpss-pas - currently used in DTSI
2. qcom,sc7180-mss-pil

Move the properties related to qcom,sc7180-mss-pil (qcom,halt-regs,
qcom,spare-regs, resets, additional clocks and regs) to specific boards
using the PIL, to silence DT schema warnings.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221124184333.133911-4-krzysztof.kozlowski@linaro.org

arch/arm64/boot/dts/qcom/sc7180-idp.dts

@@ -370,8 +370,26 @@ &qupv3_id_1 {
 &remoteproc_mpss {
 	status = "okay";
 	compatible = "qcom,sc7180-mss-pil";
+	reg = <0 0x04080000 0 0x4040>, <0 0x04180000 0 0x48>;
+	reg-names = "qdsp6", "rmb";
+
+	clocks = <&gcc GCC_MSS_CFG_AHB_CLK>,
+		 <&gcc GCC_MSS_Q6_MEMNOC_AXI_CLK>,
+		 <&gcc GCC_MSS_NAV_AXI_CLK>,
+		 <&gcc GCC_MSS_SNOC_AXI_CLK>,
+		 <&gcc GCC_MSS_MFAB_AXIS_CLK>,
+		 <&rpmhcc RPMH_CXO_CLK>;
+	clock-names = "iface", "bus", "nav", "snoc_axi", "mnoc_axi", "xo";
+
 	iommus = <&apps_smmu 0x461 0x0>, <&apps_smmu 0x444 0x3>;
 	memory-region = <&mba_mem &mpss_mem>;
+
+	resets = <&aoss_reset AOSS_CC_MSS_RESTART>,
+		 <&pdc_reset PDC_MODEM_SYNC_RESET>;
+	reset-names = "mss_restart", "pdc_reset";
+
+	qcom,halt-regs = <&tcsr_regs_1 0x3000 0x5000 0x4000>;
+	qcom,spare-regs = <&tcsr_regs_2 0xb3e4>;
 };
 
 &sdhc_1 {

arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi

@@ -853,12 +853,30 @@ &qupv3_id_1 {
 &remoteproc_mpss {
 	status = "okay";
 	compatible = "qcom,sc7180-mss-pil";
+	reg = <0 0x04080000 0 0x4040>, <0 0x04180000 0 0x48>;
+	reg-names = "qdsp6", "rmb";
+
+	clocks = <&gcc GCC_MSS_CFG_AHB_CLK>,
+		 <&gcc GCC_MSS_Q6_MEMNOC_AXI_CLK>,
+		 <&gcc GCC_MSS_NAV_AXI_CLK>,
+		 <&gcc GCC_MSS_SNOC_AXI_CLK>,
+		 <&gcc GCC_MSS_MFAB_AXIS_CLK>,
+		 <&rpmhcc RPMH_CXO_CLK>;
+	clock-names = "iface", "bus", "nav", "snoc_axi", "mnoc_axi", "xo";
+
 	iommus = <&apps_smmu 0x461 0x0>, <&apps_smmu 0x444 0x3>;
 	memory-region = <&mba_mem &mpss_mem>;
 
 	/* This gets overridden for SKUs with LTE support. */
 	firmware-name = "qcom/sc7180-trogdor/modem-nolte/mba.mbn",
 			"qcom/sc7180-trogdor/modem-nolte/qdsp6sw.mbn";
+
+	resets = <&aoss_reset AOSS_CC_MSS_RESTART>,
+		 <&pdc_reset PDC_MODEM_SYNC_RESET>;
+	reset-names = "mss_restart", "pdc_reset";
+
+	qcom,halt-regs = <&tcsr_regs_1 0x3000 0x5000 0x4000>;
+	qcom,spare-regs = <&tcsr_regs_2 0xb3e4>;
 };
 
 &sdhc_1 {

arch/arm64/boot/dts/qcom/sc7180.dtsi

@@ -1929,8 +1929,7 @@ pri_mi2s_mclk_active: pri-mi2s-mclk-active-state {
 
 		remoteproc_mpss: remoteproc@4080000 {
 			compatible = "qcom,sc7180-mpss-pas";
-			reg = <0 0x04080000 0 0x4040>, <0 0x04180000 0 0x48>;
-			reg-names = "qdsp6", "rmb";
+			reg = <0 0x04080000 0 0x4040>;
 
 			interrupts-extended = <&intc GIC_SPI 266 IRQ_TYPE_EDGE_RISING>,
 					      <&modem_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
@@ -1941,14 +1940,8 @@ remoteproc_mpss: remoteproc@4080000 {
 			interrupt-names = "wdog", "fatal", "ready", "handover",
 					  "stop-ack", "shutdown-ack";
 
-			clocks = <&gcc GCC_MSS_CFG_AHB_CLK>,
-				 <&gcc GCC_MSS_Q6_MEMNOC_AXI_CLK>,
-				 <&gcc GCC_MSS_NAV_AXI_CLK>,
-				 <&gcc GCC_MSS_SNOC_AXI_CLK>,
-				 <&gcc GCC_MSS_MFAB_AXIS_CLK>,
-				 <&rpmhcc RPMH_CXO_CLK>;
-			clock-names = "iface", "bus", "nav", "snoc_axi",
-				      "mnoc_axi", "xo";
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "xo";
 
 			power-domains = <&rpmhpd SC7180_CX>,
 					<&rpmhpd SC7180_MX>,
@@ -1962,13 +1955,6 @@ remoteproc_mpss: remoteproc@4080000 {
 			qcom,smem-states = <&modem_smp2p_out 0>;
 			qcom,smem-state-names = "stop";
 
-			resets = <&aoss_reset AOSS_CC_MSS_RESTART>,
-				 <&pdc_reset PDC_MODEM_SYNC_RESET>;
-			reset-names = "mss_restart", "pdc_reset";
-
-			qcom,halt-regs = <&tcsr_regs_1 0x3000 0x5000 0x4000>;
-			qcom,spare-regs = <&tcsr_regs_2 0xb3e4>;
-
 			status = "disabled";
 
 			glink-edge {