Merge branch 'for-rmk' of...

Merge branch 'for-rmk' of git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6 into devel

Documentation/fb/pxafb.txt

@@ -5,9 +5,13 @@ The driver supports the following options, either via
 options=<OPTIONS> when modular or video=pxafb:<OPTIONS> when built in.
 
 For example:
-	modprobe pxafb options=mode:640x480-8,passive
+	modprobe pxafb options=vmem:2M,mode:640x480-8,passive
 or on the kernel command line
-	video=pxafb:mode:640x480-8,passive
+	video=pxafb:vmem:2M,mode:640x480-8,passive
+
+vmem: VIDEO_MEM_SIZE
+	Amount of video memory to allocate (can be suffixed with K or M
+	for kilobytes or megabytes)
 
 mode:XRESxYRES[-BPP]
 	XRES == LCCR1_PPL + 1
@@ -52,3 +56,87 @@ outputen:POLARITY
 pixclockpol:POLARITY
 	pixel clock polarity
 	0 => falling edge, 1 => rising edge
+
+
+Overlay Support for PXA27x and later LCD controllers
+====================================================
+
+  PXA27x and later processors support overlay1 and overlay2 on-top of the
+  base framebuffer (although under-neath the base is also possible). They
+  support palette and no-palette RGB formats, as well as YUV formats (only
+  available on overlay2). These overlays have dedicated DMA channels and
+  behave in a similar way as a framebuffer.
+
+  However, there are some differences between these overlay framebuffers
+  and normal framebuffers, as listed below:
+
+  1. overlay can start at a 32-bit word aligned position within the base
+     framebuffer, which means they have a start (x, y). This information
+     is encoded into var->nonstd (no, var->xoffset and var->yoffset are
+     not for such purpose).
+
+  2. overlay framebuffer is allocated dynamically according to specified
+     'struct fb_var_screeninfo', the amount is decided by:
+
+        var->xres_virtual * var->yres_virtual * bpp
+
+     bpp = 16 -- for RGB565 or RGBT555
+         = 24 -- for YUV444 packed
+         = 24 -- for YUV444 planar
+	 = 16 -- for YUV422 planar (1 pixel = 1 Y + 1/2 Cb + 1/2 Cr)
+	 = 12 -- for YUV420 planar (1 pixel = 1 Y + 1/4 Cb + 1/4 Cr)
+
+     NOTE:
+
+     a. overlay does not support panning in x-direction, thus
+        var->xres_virtual will always be equal to var->xres
+
+     b. line length of overlay(s) must be on a 32-bit word boundary,
+        for YUV planar modes, it is a requirement for the component
+	with minimum bits per pixel,  e.g. for YUV420, Cr component
+	for one pixel is actually 2-bits, it means the line length
+	should be a multiple of 16-pixels
+
+     c. starting horizontal position (XPOS) should start on a 32-bit
+        word boundary, otherwise the fb_check_var() will just fail.
+
+     d. the rectangle of the overlay should be within the base plane,
+        otherwise fail
+
+     Applications should follow the sequence below to operate an overlay
+     framebuffer:
+
+         a. open("/dev/fb[1-2]", ...)
+	 b. ioctl(fd, FBIOGET_VSCREENINFO, ...)
+	 c. modify 'var' with desired parameters:
+	    1) var->xres and var->yres
+	    2) larger var->yres_virtual if more memory is required,
+	       usually for double-buffering
+	    3) var->nonstd for starting (x, y) and color format
+	    4) var->{red, green, blue, transp} if RGB mode is to be used
+	 d. ioctl(fd, FBIOPUT_VSCREENINFO, ...)
+	 e. ioctl(fd, FBIOGET_FSCREENINFO, ...)
+	 f. mmap
+	 g. ...
+
+  3. for YUV planar formats, these are actually not supported within the
+     framebuffer framework, application has to take care of the offsets
+     and lengths of each component within the framebuffer.
+
+  4. var->nonstd is used to pass starting (x, y) position and color format,
+     the detailed bit fields are shown below:
+
+    31                23  20         10          0
+     +-----------------+---+----------+----------+
+     |  ... unused ... |FOR|   XPOS   |   YPOS   |
+     +-----------------+---+----------+----------+
+
+     FOR  - color format, as defined by OVERLAY_FORMAT_* in pxafb.h
+            0 - RGB
+	    1 - YUV444 PACKED
+	    2 - YUV444 PLANAR
+	    3 - YUV422 PLANAR
+	    4 - YUR420 PLANAR
+
+     XPOS - starting horizontal position
+     YPOS - starting vertical position

arch/arm/mach-pxa/generic.c

@@ -24,6 +24,7 @@
 #include <asm/system.h>
 #include <asm/pgtable.h>
 #include <asm/mach/map.h>
+#include <asm/mach-types.h>
 
 #include <mach/pxa-regs.h>
 #include <mach/reset.h>
@@ -39,6 +40,21 @@ void clear_reset_status(unsigned int mask)
 		pxa3xx_clear_reset_status(mask);
 }
 
+unsigned long get_clock_tick_rate(void)
+{
+	unsigned long clock_tick_rate;
+
+	if (cpu_is_pxa25x())
+		clock_tick_rate = 3686400;
+	else if (machine_is_mainstone())
+		clock_tick_rate = 3249600;
+	else
+		clock_tick_rate = 3250000;
+
+	return clock_tick_rate;
+}
+EXPORT_SYMBOL(get_clock_tick_rate);
+
 /*
  * Get the clock frequency as reflected by CCCR and the turbo flag.
  * We assume these values have been applied via a fcs.

arch/arm/mach-pxa/include/mach/hardware.h

@@ -291,6 +291,8 @@
  */
 extern unsigned int get_memclk_frequency_10khz(void);
 
+/* return the clock tick rate of the OS timer */
+extern unsigned long get_clock_tick_rate(void);
 #endif
 
 #if defined(CONFIG_MACH_ARMCORE) && defined(CONFIG_PCI)

arch/arm/mach-pxa/include/mach/mfp-pxa930.h

@@ -421,6 +421,7 @@
 #define GPIO20_PWM0		MFP_CFG_LPM(GPIO20, AF2, PULL_LOW)
 #define GPIO21_PWM2		MFP_CFG_LPM(GPIO21, AF3, PULL_LOW)
 #define GPIO22_PWM3		MFP_CFG_LPM(GPIO22, AF3, PULL_LOW)
+#define GPIO32_PWM0		MFP_CFG_LPM(GPIO32, AF4, PULL_LOW)
 
 /* CIR */
 #define GPIO46_CIR_OUT		MFP_CFG(GPIO46, AF1)

arch/arm/mach-pxa/include/mach/pxafb.h

@@ -113,6 +113,7 @@ struct pxafb_mach_info {
 	unsigned int num_modes;
 
 	unsigned int	lcd_conn;
+	unsigned long	video_mem_size;
 
 	u_int		fixed_modes:1,
 			cmap_inverse:1,

arch/arm/mach-pxa/include/mach/regs-lcd.h

@@ -12,27 +12,29 @@
 #define LCCR3		(0x00C)	/* LCD Controller Control Register 3 */
 #define LCCR4		(0x010)	/* LCD Controller Control Register 4 */
 #define LCCR5		(0x014)	/* LCD Controller Control Register 5 */
-#define DFBR0		(0x020)	/* DMA Channel 0 Frame Branch Register */
-#define DFBR1		(0x024)	/* DMA Channel 1 Frame Branch Register */
-#define LCSR		(0x038)	/* LCD Controller Status Register */
+#define LCSR		(0x038)	/* LCD Controller Status Register 0 */
+#define LCSR1		(0x034)	/* LCD Controller Status Register 1 */
 #define LIIDR		(0x03C)	/* LCD Controller Interrupt ID Register */
 #define TMEDRGBR	(0x040)	/* TMED RGB Seed Register */
 #define TMEDCR		(0x044)	/* TMED Control Register */
 
+#define FBR0		(0x020)	/* DMA Channel 0 Frame Branch Register */
+#define FBR1		(0x024)	/* DMA Channel 1 Frame Branch Register */
+#define FBR2		(0x028) /* DMA Channel 2 Frame Branch Register */
+#define FBR3		(0x02C) /* DMA Channel 2 Frame Branch Register */
+#define FBR4		(0x030) /* DMA Channel 2 Frame Branch Register */
+#define FBR5		(0x110) /* DMA Channel 2 Frame Branch Register */
+#define FBR6		(0x114) /* DMA Channel 2 Frame Branch Register */
+
+#define OVL1C1		(0x050)	/* Overlay 1 Control Register 1 */
+#define OVL1C2		(0x060)	/* Overlay 1 Control Register 2 */
+#define OVL2C1		(0x070)	/* Overlay 2 Control Register 1 */
+#define OVL2C2		(0x080)	/* Overlay 2 Control Register 2 */
+
 #define CMDCR		(0x100)	/* Command Control Register */
 #define PRSR		(0x104)	/* Panel Read Status Register */
 
-#define LCCR3_1BPP	(0 << 24)
-#define LCCR3_2BPP	(1 << 24)
-#define LCCR3_4BPP	(2 << 24)
-#define LCCR3_8BPP	(3 << 24)
-#define LCCR3_16BPP	(4 << 24)
-#define LCCR3_18BPP	(5 << 24)
-#define LCCR3_18BPP_P	(6 << 24)
-#define LCCR3_19BPP	(7 << 24)
-#define LCCR3_19BPP_P	(1 << 29)
-#define LCCR3_24BPP	((1 << 29) | (1 << 24))
-#define LCCR3_25BPP	((1 << 29) | (2 << 24))
+#define LCCR3_BPP(x)	((((x) & 0x7) << 24) | (((x) & 0x8) ? (1 << 29) : 0))
 
 #define LCCR3_PDFOR_0	(0 << 30)
 #define LCCR3_PDFOR_1	(1 << 30)
@@ -42,19 +44,16 @@
 #define LCCR4_PAL_FOR_0	(0 << 15)
 #define LCCR4_PAL_FOR_1	(1 << 15)
 #define LCCR4_PAL_FOR_2	(2 << 15)
+#define LCCR4_PAL_FOR_3	(3 << 15)
 #define LCCR4_PAL_FOR_MASK	(3 << 15)
 
 #define FDADR0		(0x200)	/* DMA Channel 0 Frame Descriptor Address Register */
-#define FSADR0		(0x204)	/* DMA Channel 0 Frame Source Address Register */
-#define FIDR0		(0x208)	/* DMA Channel 0 Frame ID Register */
-#define LDCMD0		(0x20C)	/* DMA Channel 0 Command Register */
 #define FDADR1		(0x210)	/* DMA Channel 1 Frame Descriptor Address Register */
-#define FSADR1		(0x214)	/* DMA Channel 1 Frame Source Address Register */
-#define FIDR1		(0x218)	/* DMA Channel 1 Frame ID Register */
-#define LDCMD1		(0x21C)	/* DMA Channel 1 Command Register */
+#define FDADR2		(0x220)	/* DMA Channel 2 Frame Descriptor Address Register */
+#define FDADR3		(0x230)	/* DMA Channel 3 Frame Descriptor Address Register */
+#define FDADR4		(0x240)	/* DMA Channel 4 Frame Descriptor Address Register */
+#define FDADR5		(0x250)	/* DMA Channel 5 Frame Descriptor Address Register */
 #define FDADR6		(0x260) /* DMA Channel 6 Frame Descriptor Address Register */
-#define FSADR6		(0x264) /* DMA Channel 6 Frame Source Address Register */
-#define FIDR6		(0x268) /* DMA Channel 6 Frame ID Register */
 
 #define LCCR0_ENB	(1 << 0)	/* LCD Controller enable */
 #define LCCR0_CMS	(1 << 1)	/* Color/Monochrome Display Select */
@@ -126,9 +125,6 @@
 #define LCCR3_PCD	Fld (8, 0)	/* Pixel Clock Divisor */
 #define LCCR3_PixClkDiv(Div)	(((Div) << FShft (LCCR3_PCD)))
 
-#define LCCR3_BPP	Fld (3, 24)	/* Bit Per Pixel */
-#define LCCR3_Bpp(Bpp)	(((Bpp) << FShft (LCCR3_BPP)))
-
 #define LCCR3_ACB	Fld (8, 8)	/* AC Bias */
 #define LCCR3_Acb(Acb)	(((Acb) << FShft (LCCR3_ACB)))
 
@@ -157,8 +153,22 @@
 #define LCSR_RD_ST	(1 << 11)	/* read status */
 #define LCSR_CMD_INT	(1 << 12)	/* command interrupt */
 
+#define LCSR1_IU(x)	(1 << ((x) + 23)) /* Input FIFO underrun */
+#define LCSR1_BS(x)	(1 << ((x) + 15)) /* Branch Status */
+#define LCSR1_EOF(x)	(1 << ((x) + 7))  /* End of Frame Status */
+#define LCSR1_SOF(x)	(1 << ((x) - 1))  /* Start of Frame Status */
+
 #define LDCMD_PAL	(1 << 26)	/* instructs DMA to load palette buffer */
 
+/* overlay control registers */
+#define OVLxC1_PPL(x)	((((x) - 1) & 0x3ff) << 0)	/* Pixels Per Line */
+#define OVLxC1_LPO(x)	((((x) - 1) & 0x3ff) << 10)	/* Number of Lines */
+#define OVLxC1_BPP(x)	(((x) & 0xf) << 20)	/* Bits Per Pixel */
+#define OVLxC1_OEN	(1 << 31)		/* Enable bit for Overlay */
+#define OVLxC2_XPOS(x)	(((x) & 0x3ff) << 0)	/* Horizontal Position */
+#define OVLxC2_YPOS(x)	(((x) & 0x3ff) << 10)	/* Vertical Position */
+#define OVL2C2_PFOR(x)	(((x) & 0x7) << 20)	/* Pixel Format */
+
 /* smartpanel related */
 #define PRSR_DATA(x)	((x) & 0xff)	/* Panel Data */
 #define PRSR_A0		(1 << 8)	/* Read Data Source */

arch/arm/mach-pxa/include/mach/timex.h

@@ -10,6 +10,14 @@
  * published by the Free Software Foundation.
  */
 
+/* Various drivers are still using the constant of CLOCK_TICK_RATE, for
+ * those drivers to at least work, the definition is provided here.
+ *
+ * NOTE: this is no longer accurate when multiple processors and boards
+ * are selected, newer drivers should not depend on this any more.  Use
+ * either the clocksource/clockevent or get this at run-time by calling
+ * get_clock_tick_rate() (as defined in generic.c).
+ */
 
 #if defined(CONFIG_PXA25x)
 /* PXA250/210 timer base */

arch/arm/mach-pxa/time.c

@@ -24,7 +24,6 @@
 #include <asm/mach/time.h>
 #include <mach/hardware.h>
 #include <mach/pxa-regs.h>
-#include <asm/mach-types.h>
 
 /*
  * This is PXA's sched_clock implementation. This has a resolution
@@ -151,18 +150,11 @@ static struct irqaction pxa_ost0_irq = {
 
 static void __init pxa_timer_init(void)
 {
-	unsigned long clock_tick_rate;
+	unsigned long clock_tick_rate = get_clock_tick_rate();
 
 	OIER = 0;
 	OSSR = OSSR_M0 | OSSR_M1 | OSSR_M2 | OSSR_M3;
 
-	if (cpu_is_pxa25x())
-		clock_tick_rate = 3686400;
-	else if (machine_is_mainstone())
-		clock_tick_rate = 3249600;
-	else
-		clock_tick_rate = 3250000;
-
 	set_oscr2ns_scale(clock_tick_rate);
 
 	ckevt_pxa_osmr0.mult =

arch/arm/mach-sa1100/include/mach/hardware.h

@@ -59,6 +59,10 @@
 # define __REG(x)	(*((volatile unsigned long *)io_p2v(x)))
 # define __PREG(x)	(io_v2p((unsigned long)&(x)))
 
+static inline unsigned long get_clock_tick_rate(void)
+{
+	return 3686400;
+}
 #else
 
 # define __REG(x)	io_p2v(x)

drivers/rtc/rtc-sa1100.c

@@ -38,11 +38,11 @@
 #include <mach/pxa-regs.h>
 #endif
 
-#define TIMER_FREQ		CLOCK_TICK_RATE
 #define RTC_DEF_DIVIDER		32768 - 1
 #define RTC_DEF_TRIM		0
 
 static unsigned long rtc_freq = 1024;
+static unsigned long timer_freq;
 static struct rtc_time rtc_alarm;
 static DEFINE_SPINLOCK(sa1100_rtc_lock);
 
@@ -157,7 +157,7 @@ static irqreturn_t timer1_interrupt(int irq, void *dev_id)
 	rtc_update_irq(rtc, rtc_timer1_count, RTC_PF | RTC_IRQF);
 
 	if (rtc_timer1_count == 1)
-		rtc_timer1_count = (rtc_freq * ((1<<30)/(TIMER_FREQ>>2)));
+		rtc_timer1_count = (rtc_freq * ((1 << 30) / (timer_freq >> 2)));
 
 	return IRQ_HANDLED;
 }
@@ -166,7 +166,7 @@ static int sa1100_rtc_read_callback(struct device *dev, int data)
 {
 	if (data & RTC_PF) {
 		/* interpolate missed periods and set match for the next */
-		unsigned long period = TIMER_FREQ/rtc_freq;
+		unsigned long period = timer_freq / rtc_freq;
 		unsigned long oscr = OSCR;
 		unsigned long osmr1 = OSMR1;
 		unsigned long missed = (oscr - osmr1)/period;
@@ -263,7 +263,7 @@ static int sa1100_rtc_ioctl(struct device *dev, unsigned int cmd,
 		return 0;
 	case RTC_PIE_ON:
 		spin_lock_irq(&sa1100_rtc_lock);
-		OSMR1 = TIMER_FREQ/rtc_freq + OSCR;
+		OSMR1 = timer_freq / rtc_freq + OSCR;
 		OIER |= OIER_E1;
 		rtc_timer1_count = 1;
 		spin_unlock_irq(&sa1100_rtc_lock);
@@ -271,7 +271,7 @@ static int sa1100_rtc_ioctl(struct device *dev, unsigned int cmd,
 	case RTC_IRQP_READ:
 		return put_user(rtc_freq, (unsigned long *)arg);
 	case RTC_IRQP_SET:
-		if (arg < 1 || arg > TIMER_FREQ)
+		if (arg < 1 || arg > timer_freq)
 			return -EINVAL;
 		rtc_freq = arg;
 		return 0;
@@ -352,6 +352,8 @@ static int sa1100_rtc_probe(struct platform_device *pdev)
 {
 	struct rtc_device *rtc;
 
+	timer_freq = get_clock_tick_rate();
+
 	/*
 	 * According to the manual we should be able to let RTTR be zero
 	 * and then a default diviser for a 32.768KHz clock is used.

drivers/video/Kconfig

@@ -1817,6 +1817,11 @@ config FB_PXA
 
 	  If unsure, say N.
 
+config FB_PXA_OVERLAY
+	bool "Support PXA27x/PXA3xx Overlay(s) as framebuffer"
+	default n
+	depends on FB_PXA && (PXA27x || PXA3xx)
+
 config FB_PXA_SMARTPANEL
 	bool "PXA Smartpanel LCD support"
 	default n

drivers/video/pxafb.h

@@ -54,11 +54,55 @@ enum {
 #define PALETTE_SIZE	(256 * 4)
 #define CMD_BUFF_SIZE	(1024 * 50)
 
+/* NOTE: the palette and frame dma descriptors are doubled to allow
+ * the 2nd set for branch settings (FBRx)
+ */
 struct pxafb_dma_buff {
 	unsigned char palette[PAL_MAX * PALETTE_SIZE];
 	uint16_t cmd_buff[CMD_BUFF_SIZE];
-	struct pxafb_dma_descriptor pal_desc[PAL_MAX];
-	struct pxafb_dma_descriptor dma_desc[DMA_MAX];
+	struct pxafb_dma_descriptor pal_desc[PAL_MAX * 2];
+	struct pxafb_dma_descriptor dma_desc[DMA_MAX * 2];
+};
+
+enum {
+	OVERLAY1,
+	OVERLAY2,
+};
+
+enum {
+	OVERLAY_FORMAT_RGB = 0,
+	OVERLAY_FORMAT_YUV444_PACKED,
+	OVERLAY_FORMAT_YUV444_PLANAR,
+	OVERLAY_FORMAT_YUV422_PLANAR,
+	OVERLAY_FORMAT_YUV420_PLANAR,
+};
+
+#define NONSTD_TO_XPOS(x)	(((x) >> 0)  & 0x3ff)
+#define NONSTD_TO_YPOS(x)	(((x) >> 10) & 0x3ff)
+#define NONSTD_TO_PFOR(x)	(((x) >> 20) & 0x7)
+
+struct pxafb_layer;
+
+struct pxafb_layer_ops {
+	void (*enable)(struct pxafb_layer *);
+	void (*disable)(struct pxafb_layer *);
+	void (*setup)(struct pxafb_layer *);
+};
+
+struct pxafb_layer {
+	struct fb_info		fb;
+	int			id;
+	atomic_t		usage;
+	uint32_t		control[2];
+
+	struct pxafb_layer_ops	*ops;
+
+	void __iomem		*video_mem;
+	unsigned long		video_mem_phys;
+	size_t			video_mem_size;
+	struct completion	branch_done;
+
+	struct pxafb_info	*fbi;
 };
 
 struct pxafb_info {
@@ -69,24 +113,15 @@ struct pxafb_info {
 	void __iomem		*mmio_base;
 
 	struct pxafb_dma_buff	*dma_buff;
+	size_t			dma_buff_size;
 	dma_addr_t		dma_buff_phys;
-	dma_addr_t		fdadr[DMA_MAX];
-
-	/*
-	 * These are the addresses we mapped
-	 * the framebuffer memory region to.
-	 */
-	/* raw memory addresses */
-	dma_addr_t		map_dma;	/* physical */
-	u_char *		map_cpu;	/* virtual */
-	u_int			map_size;
-
-	/* addresses of pieces placed in raw buffer */
-	u_char *		screen_cpu;	/* virtual address of frame buffer */
-	dma_addr_t		screen_dma;	/* physical address of frame buffer */
+	dma_addr_t		fdadr[DMA_MAX * 2];
+
+	void __iomem		*video_mem;	/* virtual address of frame buffer */
+	unsigned long		video_mem_phys;	/* physical address of frame buffer */
+	size_t			video_mem_size;	/* size of the frame buffer */
 	u16 *			palette_cpu;	/* virtual address of palette memory */
 	u_int			palette_size;
-	ssize_t			video_offset;
 
 	u_int			lccr0;
 	u_int			lccr3;
@@ -120,6 +155,10 @@ struct pxafb_info {
 	struct task_struct	*smart_thread;
 #endif
 
+#ifdef CONFIG_FB_PXA_OVERLAY
+	struct pxafb_layer	overlay[2];
+#endif
+
 #ifdef CONFIG_CPU_FREQ
 	struct notifier_block	freq_transition;
 	struct notifier_block	freq_policy;
@@ -151,4 +190,10 @@ struct pxafb_info {
 #define MIN_XRES	64
 #define MIN_YRES	64
 
+/* maximum X and Y resolutions - note these are limits from the register
+ * bits length instead of the real ones
+ */
+#define MAX_XRES	1024
+#define MAX_YRES	1024
+
 #endif /* __PXAFB_H__ */

drivers/watchdog/sa1100_wdt.c

@@ -36,8 +36,7 @@
 #include <mach/reset.h>
 #include <mach/hardware.h>
 
-#define OSCR_FREQ		CLOCK_TICK_RATE
-
+static unsigned long oscr_freq;
 static unsigned long sa1100wdt_users;
 static int pre_margin;
 static int boot_status;
@@ -124,12 +123,12 @@ static long sa1100dog_ioctl(struct file *file, unsigned int cmd,
 			break;
 		}
 
-		pre_margin = OSCR_FREQ * time;
+		pre_margin = oscr_freq * time;
 		OSMR3 = OSCR + pre_margin;
 		/*fall through*/
 
 	case WDIOC_GETTIMEOUT:
-		ret = put_user(pre_margin / OSCR_FREQ, p);
+		ret = put_user(pre_margin / oscr_freq, p);
 		break;
 	}
 	return ret;
@@ -156,6 +155,8 @@ static int __init sa1100dog_init(void)
 {
 	int ret;
 
+	oscr_freq = get_clock_tick_rate();
+
 	/*
 	 * Read the reset status, and save it for later.  If
 	 * we suspend, RCSR will be cleared, and the watchdog
@@ -163,7 +164,7 @@ static int __init sa1100dog_init(void)
 	 */
 	boot_status = (reset_status & RESET_STATUS_WATCHDOG) ?
 				WDIOF_CARDRESET : 0;
-	pre_margin = OSCR_FREQ * margin;
+	pre_margin = oscr_freq * margin;
 
 	ret = misc_register(&sa1100dog_miscdev);
 	if (ret == 0)