Commit 48e0d373 authored by Chunfeng Yun's avatar Chunfeng Yun Committed by Greg Kroah-Hartman

usb: mtu3: supports new QMU format

In order to support U3gen2 ISOC transfer upto 96DPs, extend
the data buffer length.
Signed-off-by: default avatarChunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
parent 09befc32
......@@ -148,22 +148,23 @@ struct mtu3_fifo_info {
* bit0: Hardware Own (HWO)
* bit1: Buffer Descriptor Present (BDP), always 0, BD is not supported
* bit2: Bypass (BPS), 1: HW skips this GPD if HWO = 1
* bit6: [EL] Zero Length Packet (ZLP), moved from @dw3_info[29]
* bit7: Interrupt On Completion (IOC)
* bit[31:16]: allow data buffer length (RX ONLY),
* bit[31:16]: ([EL] bit[31:12]) allow data buffer length (RX ONLY),
* the buffer length of the data to receive
* bit[23:16]: extension address (TX ONLY),
* bit[23:16]: ([EL] bit[31:24]) extension address (TX ONLY),
* lower 4 bits are extension bits of @buffer,
* upper 4 bits are extension bits of @next_gpd
* @next_gpd: Physical address of the next GPD
* @buffer: Physical address of the data buffer
* @dw3_info:
* bit[15:0]: data buffer length,
* bit[15:0]: ([EL] bit[19:0]) data buffer length,
* (TX): the buffer length of the data to transmit
* (RX): The total length of data received
* bit[23:16]: extension address (RX ONLY),
* bit[23:16]: ([EL] bit[31:24]) extension address (RX ONLY),
* lower 4 bits are extension bits of @buffer,
* upper 4 bits are extension bits of @next_gpd
* bit29: Zero Length Packet (ZLP) (TX ONLY)
* bit29: ([EL] abandoned) Zero Length Packet (ZLP) (TX ONLY)
*/
struct qmu_gpd {
__le32 dw0_info;
......
......@@ -601,6 +601,10 @@ static void mtu3_regs_init(struct mtu3 *mtu)
mtu3_clrbits(mbase, U3D_MISC_CTRL, VBUS_FRC_EN | VBUS_ON);
/* enable automatical HWRW from L1 */
mtu3_setbits(mbase, U3D_POWER_MANAGEMENT, LPM_HRWE);
/* use new QMU format when HW version >= 0x1003 */
if (mtu->gen2cp)
mtu3_writel(mbase, U3D_QFCR, ~0x0);
}
static irqreturn_t mtu3_link_isr(struct mtu3 *mtu)
......@@ -755,6 +759,7 @@ static int mtu3_hw_init(struct mtu3 *mtu)
value = mtu3_readl(mtu->ippc_base, U3D_SSUSB_IP_TRUNK_VERS);
mtu->hw_version = IP_TRUNK_VERS(value);
mtu->gen2cp = !!(mtu->hw_version >= MTU3_TRUNK_VERS_1003);
value = mtu3_readl(mtu->ippc_base, U3D_SSUSB_IP_DEV_CAP);
mtu->is_u3_ip = !!SSUSB_IP_DEV_U3_PORT_NUM(value);
......
......@@ -278,10 +278,12 @@ static int mtu3_gadget_queue(struct usb_ep *ep,
__func__, mep->is_in ? "TX" : "RX", mreq->epnum, ep->name,
mreq, ep->maxpacket, mreq->request.length);
if (req->length > GPD_BUF_SIZE) {
if (req->length > GPD_BUF_SIZE ||
(mtu->gen2cp && req->length > GPD_BUF_SIZE_EL)) {
dev_warn(mtu->dev,
"req length > supported MAX:%d requested:%d\n",
GPD_BUF_SIZE, req->length);
mtu->gen2cp ? GPD_BUF_SIZE_EL : GPD_BUF_SIZE,
req->length);
return -EOPNOTSUPP;
}
......
......@@ -49,6 +49,7 @@
#define U3D_QCR1 (SSUSB_DEV_BASE + 0x0404)
#define U3D_QCR2 (SSUSB_DEV_BASE + 0x0408)
#define U3D_QCR3 (SSUSB_DEV_BASE + 0x040C)
#define U3D_QFCR (SSUSB_DEV_BASE + 0x0428)
#define U3D_TXQHIAR1 (SSUSB_DEV_BASE + 0x0484)
#define U3D_RXQHIAR1 (SSUSB_DEV_BASE + 0x04C4)
......
......@@ -28,14 +28,42 @@
#define GPD_FLAGS_HWO BIT(0)
#define GPD_FLAGS_BDP BIT(1)
#define GPD_FLAGS_BPS BIT(2)
#define GPD_FLAGS_ZLP BIT(6)
#define GPD_FLAGS_IOC BIT(7)
#define GET_GPD_HWO(gpd) (le32_to_cpu((gpd)->dw0_info) & GPD_FLAGS_HWO)
#define GPD_RX_BUF_LEN(x) (((x) & 0xffff) << 16)
#define GPD_DATA_LEN(x) ((x) & 0xffff)
#define GPD_RX_BUF_LEN_OG(x) (((x) & 0xffff) << 16)
#define GPD_RX_BUF_LEN_EL(x) (((x) & 0xfffff) << 12)
#define GPD_RX_BUF_LEN(mtu, x) \
({ \
typeof(x) x_ = (x); \
((mtu)->gen2cp) ? GPD_RX_BUF_LEN_EL(x_) : GPD_RX_BUF_LEN_OG(x_); \
})
#define GPD_DATA_LEN_OG(x) ((x) & 0xffff)
#define GPD_DATA_LEN_EL(x) ((x) & 0xfffff)
#define GPD_DATA_LEN(mtu, x) \
({ \
typeof(x) x_ = (x); \
((mtu)->gen2cp) ? GPD_DATA_LEN_EL(x_) : GPD_DATA_LEN_OG(x_); \
})
#define GPD_EXT_FLAG_ZLP BIT(29)
#define GPD_EXT_NGP(x) (((x) & 0xf) << 20)
#define GPD_EXT_BUF(x) (((x) & 0xf) << 16)
#define GPD_EXT_NGP_OG(x) (((x) & 0xf) << 20)
#define GPD_EXT_BUF_OG(x) (((x) & 0xf) << 16)
#define GPD_EXT_NGP_EL(x) (((x) & 0xf) << 28)
#define GPD_EXT_BUF_EL(x) (((x) & 0xf) << 24)
#define GPD_EXT_NGP(mtu, x) \
({ \
typeof(x) x_ = (x); \
((mtu)->gen2cp) ? GPD_EXT_NGP_EL(x_) : GPD_EXT_NGP_OG(x_); \
})
#define GPD_EXT_BUF(mtu, x) \
({ \
typeof(x) x_ = (x); \
((mtu)->gen2cp) ? GPD_EXT_BUF_EL(x_) : GPD_EXT_BUF_OG(x_); \
})
#define HILO_GEN64(hi, lo) (((u64)(hi) << 32) + (lo))
#define HILO_DMA(hi, lo) \
......@@ -217,13 +245,14 @@ static int mtu3_prepare_tx_gpd(struct mtu3_ep *mep, struct mtu3_request *mreq)
struct mtu3_gpd_ring *ring = &mep->gpd_ring;
struct qmu_gpd *gpd = ring->enqueue;
struct usb_request *req = &mreq->request;
struct mtu3 *mtu = mep->mtu;
dma_addr_t enq_dma;
u32 ext_addr;
gpd->dw0_info = 0; /* SW own it */
gpd->buffer = cpu_to_le32(lower_32_bits(req->dma));
ext_addr = GPD_EXT_BUF(upper_32_bits(req->dma));
gpd->dw3_info = cpu_to_le32(GPD_DATA_LEN(req->length));
ext_addr = GPD_EXT_BUF(mtu, upper_32_bits(req->dma));
gpd->dw3_info = cpu_to_le32(GPD_DATA_LEN(mtu, req->length));
/* get the next GPD */
enq = advance_enq_gpd(ring);
......@@ -233,11 +262,15 @@ static int mtu3_prepare_tx_gpd(struct mtu3_ep *mep, struct mtu3_request *mreq)
enq->dw0_info &= cpu_to_le32(~GPD_FLAGS_HWO);
gpd->next_gpd = cpu_to_le32(lower_32_bits(enq_dma));
ext_addr |= GPD_EXT_NGP(upper_32_bits(enq_dma));
ext_addr |= GPD_EXT_NGP(mtu, upper_32_bits(enq_dma));
gpd->dw0_info = cpu_to_le32(ext_addr);
if (req->zero)
gpd->dw3_info |= cpu_to_le32(GPD_EXT_FLAG_ZLP);
if (req->zero) {
if (mtu->gen2cp)
gpd->dw0_info |= cpu_to_le32(GPD_FLAGS_ZLP);
else
gpd->dw3_info |= cpu_to_le32(GPD_EXT_FLAG_ZLP);
}
gpd->dw0_info |= cpu_to_le32(GPD_FLAGS_IOC | GPD_FLAGS_HWO);
......@@ -252,13 +285,14 @@ static int mtu3_prepare_rx_gpd(struct mtu3_ep *mep, struct mtu3_request *mreq)
struct mtu3_gpd_ring *ring = &mep->gpd_ring;
struct qmu_gpd *gpd = ring->enqueue;
struct usb_request *req = &mreq->request;
struct mtu3 *mtu = mep->mtu;
dma_addr_t enq_dma;
u32 ext_addr;
gpd->dw0_info = 0; /* SW own it */
gpd->buffer = cpu_to_le32(lower_32_bits(req->dma));
ext_addr = GPD_EXT_BUF(upper_32_bits(req->dma));
gpd->dw0_info = cpu_to_le32(GPD_RX_BUF_LEN(req->length));
ext_addr = GPD_EXT_BUF(mtu, upper_32_bits(req->dma));
gpd->dw0_info = cpu_to_le32(GPD_RX_BUF_LEN(mtu, req->length));
/* get the next GPD */
enq = advance_enq_gpd(ring);
......@@ -268,7 +302,7 @@ static int mtu3_prepare_rx_gpd(struct mtu3_ep *mep, struct mtu3_request *mreq)
enq->dw0_info &= cpu_to_le32(~GPD_FLAGS_HWO);
gpd->next_gpd = cpu_to_le32(lower_32_bits(enq_dma));
ext_addr |= GPD_EXT_NGP(upper_32_bits(enq_dma));
ext_addr |= GPD_EXT_NGP(mtu, upper_32_bits(enq_dma));
gpd->dw3_info = cpu_to_le32(ext_addr);
gpd->dw0_info |= cpu_to_le32(GPD_FLAGS_IOC | GPD_FLAGS_HWO);
......@@ -391,7 +425,7 @@ static void qmu_tx_zlp_error_handler(struct mtu3 *mtu, u8 epnum)
cur_gpd_dma = read_txq_cur_addr(mbase, epnum);
gpd_current = gpd_dma_to_virt(ring, cur_gpd_dma);
if (GPD_DATA_LEN(le32_to_cpu(gpd_current->dw3_info)) != 0) {
if (GPD_DATA_LEN(mtu, le32_to_cpu(gpd_current->dw3_info)) != 0) {
dev_err(mtu->dev, "TX EP%d buffer length error(!=0)\n", epnum);
return;
}
......@@ -451,7 +485,7 @@ static void qmu_done_tx(struct mtu3 *mtu, u8 epnum)
}
request = &mreq->request;
request->actual = GPD_DATA_LEN(le32_to_cpu(gpd->dw3_info));
request->actual = GPD_DATA_LEN(mtu, le32_to_cpu(gpd->dw3_info));
mtu3_req_complete(mep, request, 0);
gpd = advance_deq_gpd(ring);
......@@ -489,7 +523,7 @@ static void qmu_done_rx(struct mtu3 *mtu, u8 epnum)
}
req = &mreq->request;
req->actual = GPD_DATA_LEN(le32_to_cpu(gpd->dw3_info));
req->actual = GPD_DATA_LEN(mtu, le32_to_cpu(gpd->dw3_info));
mtu3_req_complete(mep, req, 0);
gpd = advance_deq_gpd(ring);
......
......@@ -15,6 +15,7 @@
#define QMU_GPD_RING_SIZE (MAX_GPD_NUM * QMU_GPD_SIZE)
#define GPD_BUF_SIZE 65532
#define GPD_BUF_SIZE_EL 1048572
void mtu3_qmu_stop(struct mtu3_ep *mep);
int mtu3_qmu_start(struct mtu3_ep *mep);
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment