arm64: dts: ti: k3-j7200: Add overlay to enable CPSW5G ports in QSGMII mode

The J7 Quad Port Add-On Ethernet Card for J7200 Common-Proc-Board supports
QSGMII mode. Use the overlay to configure CPSW5G ports in QSGMII mode.

Add support to reset the PHY from kernel by using gpio-hog and gpio-reset.

Add aliases for CPSW5G ports to enable kernel to fetch MAC addresses
directly from U-Boot.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20230315062307.1612220-5-s-vadapalli@ti.comSigned-off-by: Nishanth Menon <nm@ti.com>

arch/arm64/boot/dts/ti/Makefile

@@ -28,7 +28,8 @@ dtb-$(CONFIG_ARCH_K3) += k3-am6548-iot2050-advanced-pg2.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am654-base-board.dtb
 
 # Boards with J7200 SoC
-dtb-$(CONFIG_ARCH_K3) += k3-j7200-common-proc-board.dtb
+k3-j7200-evm-dtbs := k3-j7200-common-proc-board.dtb k3-j7200-evm-quad-port-eth-exp.dtbo
+dtb-$(CONFIG_ARCH_K3) += k3-j7200-evm.dtb
 
 # Boards with J721e SoC
 k3-j721e-evm-dtbs := k3-j721e-common-proc-board.dtb k3-j721e-evm-quad-port-eth-exp.dtbo

arch/arm64/boot/dts/ti/k3-j7200-evm-quad-port-eth-exp.dtso

+// SPDX-License-Identifier: GPL-2.0
+/**
+ * DT Overlay for CPSW5G in QSGMII mode using J7 Quad Port ETH EXP Add-On Ethernet Card with
+ * J7200 board.
+ *
+ * Copyright (C) 2023 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mux/ti-serdes.h>
+
+#include "k3-pinctrl.h"
+
+&{/} {
+	aliases {
+		ethernet1 = "/bus@100000/ethernet@c000000/ethernet-ports/port@1";
+		ethernet2 = "/bus@100000/ethernet@c000000/ethernet-ports/port@2";
+		ethernet3 = "/bus@100000/ethernet@c000000/ethernet-ports/port@3";
+		ethernet4 = "/bus@100000/ethernet@c000000/ethernet-ports/port@4";
+	};
+};
+
+&cpsw0 {
+	status = "okay";
+};
+
+&cpsw0_port1 {
+	status = "okay";
+	phy-handle = <&cpsw5g_phy0>;
+	phy-mode = "qsgmii";
+	mac-address = [00 00 00 00 00 00];
+	phys = <&cpsw0_phy_gmii_sel 1>;
+};
+
+&cpsw0_port2 {
+	status = "okay";
+	phy-handle = <&cpsw5g_phy1>;
+	phy-mode = "qsgmii";
+	mac-address = [00 00 00 00 00 00];
+	phys = <&cpsw0_phy_gmii_sel 2>;
+};
+
+&cpsw0_port3 {
+	status = "okay";
+	phy-handle = <&cpsw5g_phy2>;
+	phy-mode = "qsgmii";
+	mac-address = [00 00 00 00 00 00];
+	phys = <&cpsw0_phy_gmii_sel 3>;
+};
+
+&cpsw0_port4 {
+	status = "okay";
+	phy-handle = <&cpsw5g_phy3>;
+	phy-mode = "qsgmii";
+	mac-address = [00 00 00 00 00 00];
+	phys = <&cpsw0_phy_gmii_sel 4>;
+};
+
+&cpsw5g_mdio {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mdio0_pins_default>;
+	reset-gpios = <&exp2 17 GPIO_ACTIVE_LOW>;
+	reset-post-delay-us = <120000>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	cpsw5g_phy0: ethernet-phy@16 {
+		reg = <16>;
+	};
+	cpsw5g_phy1: ethernet-phy@17 {
+		reg = <17>;
+	};
+	cpsw5g_phy2: ethernet-phy@18 {
+		reg = <18>;
+	};
+	cpsw5g_phy3: ethernet-phy@19 {
+		reg = <19>;
+	};
+};
+
+&exp2 {
+	qsgmii-line-hog {
+		gpio-hog;
+		gpios = <16 GPIO_ACTIVE_HIGH>;
+		output-low;
+		line-name = "qsgmii-pwrdn-line";
+	};
+};
+
+&main_pmx0 {
+	mdio0_pins_default: mdio0-pins-default {
+		pinctrl-single,pins = <
+			J721E_IOPAD(0x00a8, PIN_OUTPUT, 5) /* (W19) UART8_TXD.MDIO0_MDC */
+			J721E_IOPAD(0x00a4, PIN_INPUT, 5) /* (W14) UART8_RXD.MDIO0_MDIO */
+		>;
+	};
+};