[ARM] Orion: export red SATA lights on TS-409, fix SATA presence/activity

Export the four red SATA LEDs on the QNAP TS-409 that are connected
through gpio.  Since the boot loader apparently sets the SATA LEDs 2-4
to red and the SATA LED can only be red or green (but not both),
exporting the red SATA LEDs (which automatically turns them off upon
boot) makes the green SATA presence/activity indication visible.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Acked-by: Sylver Bruneau <sylver.bruneau@googlemail.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>

arch/arm/mach-orion5x/ts409-setup.c

@@ -3,6 +3,9 @@
  *
  * Maintainer: Sylver Bruneau <sylver.bruneau@gmail.com>
  *
+ * Copyright (C) 2008  Sylver Bruneau <sylver.bruneau@gmail.com>
+ * Copyright (C) 2008  Martin Michlmayr <tbm@cyrius.com>
+ *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License
  * as published by the Free Software Foundation; either version
@@ -16,6 +19,7 @@
 #include <linux/irq.h>
 #include <linux/mtd/physmap.h>
 #include <linux/mv643xx_eth.h>
+#include <linux/leds.h>
 #include <linux/gpio_keys.h>
 #include <linux/input.h>
 #include <linux/i2c.h>
@@ -162,6 +166,43 @@ static struct i2c_board_info __initdata qnap_ts409_i2c_rtc = {
 	I2C_BOARD_INFO("s35390a", 0x30),
 };
 
+/*****************************************************************************
+ * LEDs attached to GPIO
+ ****************************************************************************/
+
+static struct gpio_led ts409_led_pins[] = {
+	{
+		.name		= "ts409:red:sata1",
+		.gpio		= 4,
+		.active_low	= 1,
+	}, {
+		.name		= "ts409:red:sata2",
+		.gpio		= 5,
+		.active_low	= 1,
+	}, {
+		.name		= "ts409:red:sata3",
+		.gpio		= 6,
+		.active_low	= 1,
+	}, {
+		.name		= "ts409:red:sata4",
+		.gpio		= 7,
+		.active_low	= 1,
+	},
+};
+
+static struct gpio_led_platform_data ts409_led_data = {
+	.leds		= ts409_led_pins,
+	.num_leds	= ARRAY_SIZE(ts409_led_pins),
+};
+
+static struct platform_device ts409_leds = {
+	.name	= "leds-gpio",
+	.id	= -1,
+	.dev	= {
+		.platform_data	= &ts409_led_data,
+	},
+};
+
 /****************************************************************************
  * GPIO Attached Keys
  *     Power button is attached to the PIC microcontroller
@@ -255,6 +296,7 @@ static void __init qnap_ts409_init(void)
 	if (qnap_ts409_i2c_rtc.irq == 0)
 		pr_warning("qnap_ts409_init: failed to get RTC IRQ\n");
 	i2c_register_board_info(0, &qnap_ts409_i2c_rtc, 1);
+	platform_device_register(&ts409_leds);
 
 	/* register tsx09 specific power-off method */
 	pm_power_off = qnap_tsx09_power_off;