Merge bk://linux-scsi.bkbits.net/scsi-bugfixes-2.6

into home.osdl.org:/home/torvalds/v2.5/linux

drivers/block/scsi_ioctl.c

@@ -124,6 +124,8 @@ static int sg_set_reserved_size(request_queue_t *q, int *p)
 	if (err)
 		return err;
 
+	if (size < 0)
+		return -EINVAL;
 	if (size > (q->max_sectors << 9))
 		return -EINVAL;
 

drivers/scsi/aacraid/aacraid.h

@@ -14,6 +14,8 @@
 #define AAC_MAX_TARGET (MAXIMUM_NUM_CONTAINERS+1)
 #define AAC_MAX_LUN	(8)
 
+#define AAC_MAX_HOSTPHYSMEMPAGES (0xfffff)
+
 /*
  * These macros convert from physical channels to virtual channels
  */

drivers/scsi/aacraid/comminit.c

@@ -92,7 +92,21 @@ static int aac_alloc_comm(struct aac_dev *dev, void **commaddr, unsigned long co
 	init->AdapterFibsPhysicalAddress = cpu_to_le32((u32)phys);
 	init->AdapterFibsSize = cpu_to_le32(fibsize);
 	init->AdapterFibAlign = cpu_to_le32(sizeof(struct hw_fib));
-	init->HostPhysMemPages = cpu_to_le32(num_physpages);		// number of 4k pages of host physical memory
+	/* 
+	 * number of 4k pages of host physical memory. The aacraid fw needs
+	 * this number to be less than 4gb worth of pages. num_physpages is in
+	 * system page units. New firmware doesn't have any issues with the
+	 * mapping system, but older Firmware did, and had *troubles* dealing
+	 * with the math overloading past 32 bits, thus we must limit this
+	 * field.
+	 */
+	if ((num_physpages << (PAGE_SHIFT - 12)) <= AAC_MAX_HOSTPHYSMEMPAGES) {
+		init->HostPhysMemPages = 
+			cpu_to_le32(num_physpages << (PAGE_SHIFT-12));
+	} else {
+		init->HostPhysMemPages = cpu_to_le32(AAC_MAX_HOSTPHYSMEMPAGES);
+	}
+
 
 	/*
 	 * Increment the base address by the amount already used

drivers/scsi/constants.c

@@ -62,42 +62,54 @@ static const char *group_1_commands[] = {
 
 
 static const char *group_2_commands[] = {
-/* 40-41 */ "Change Definition", "Write Same", 
-/* 42-48 */ "Read sub-channel", "Read TOC", "Read header", 
-            "Play audio (10)", unknown, "Play audio msf",
-            "Play audio track/index", 
-/* 49-4f */ "Play track relative (10)", unknown, "Pause/resume", 
-            "Log Select", "Log Sense", unknown, unknown,
-/* 50-55 */ unknown, unknown, unknown, unknown, unknown, "Mode Select (10)",
-/* 56-5b */ unknown, unknown, unknown, unknown, "Mode Sense (10)", unknown,
-/* 5c-5f */ unknown, unknown, unknown,
+/* 40-41 */ "Change Definition", "Write Same",
+/* 42-48 */ "Read sub-channel", "Read TOC", "Read header",
+            "Play audio (10)", "Get configuration", "Play audio msf",
+            "Play audio track/index",
+/* 49-4f */ "Play track relative (10)", "Get event status notification",
+            "Pause/resume", "Log Select", "Log Sense", "Stop play/scan",
+            unknown,
+/* 50-55 */ "Xdwrite", "Xpwrite, Read disk info", "Xdread, Read track info",
+            "Reserve track", "Send OPC onfo", "Mode Select (10)",
+/* 56-5b */ "Reserve (10)", "Release (10)", "Repair track", "Read master cue",
+            "Mode Sense (10)", "Close track/session",
+/* 5c-5f */ "Read buffer capacity", "Send cue sheet", "Persistent reserve in",
+            "Persistent reserve out",
 };
 
 
 /* The following are 16 byte commands in group 4 */
 static const char *group_4_commands[] = {
-/* 80-84 */ unknown, unknown, unknown, unknown, unknown,
-/* 85-89 */ "Memory Export In (16)", unknown, unknown, unknown,
-            "Memory Export Out (16)",
-/* 8a-8f */ unknown, unknown, unknown, unknown, unknown, unknown,
-/* 90-94 */ unknown, unknown, unknown, unknown, unknown,
+/* 80-84 */ "Xdwrite (16)", "Rebuild (16)", "Regenerate (16)", "Extended copy",
+            "Receive copy results",
+/* 85-89 */ "Memory Export In (16)", "Access control in", "Access control out",
+            "Read (16)", "Memory Export Out (16)",
+/* 8a-8f */ "Write (16)", unknown, "Read attributes", "Write attributes",
+            "Write and verify (16)", "Verify (16)",
+/* 90-94 */ "Pre-fetch (16)", "Synchronize cache (16)",
+            "Lock/unlock cache (16)", "Write same (16)", unknown,
 /* 95-99 */ unknown, unknown, unknown, unknown, unknown,
-/* 9a-9f */ unknown, unknown, unknown, unknown, unknown, unknown,
+/* 9a-9f */ unknown, unknown, unknown, unknown, "Service action in",
+            "Service action out",
 };
 
-
 /* The following are 12 byte commands in group 5 */
 static const char *group_5_commands[] = {
-/* a0-a5 */ unknown, unknown, unknown, unknown, unknown,
-            "Move medium/play audio(12)",
-/* a6-a9 */ "Exchange medium", unknown, "Read(12)", "Play track relative(12)", 
-/* aa-ae */ "Write(12)", unknown, "Erase(12)", unknown, 
-            "Write and verify(12)", 
+/* a0-a5 */ "Report luns", "Blank", "Send event", "Maintenance (in)",
+            "Maintenance (out)", "Move medium/play audio(12)",
+/* a6-a9 */ "Exchange medium", "Move medium attached", "Read(12)",
+            "Play track relative(12)",
+/* aa-ae */ "Write(12)", unknown, "Erase(12), Get Performance",
+            "Read DVD structure", "Write and verify(12)",
 /* af-b1 */ "Verify(12)", "Search data high(12)", "Search data equal(12)",
-/* b2-b4 */ "Search data low(12)", "Set limits(12)", unknown,
-/* b5-b6 */ "Request volume element address", "Send volume tag",
-/* b7-b9 */ "Read defect data(12)", "Read element status", unknown,
-/* ba-bf */ unknown, unknown, unknown, unknown, unknown, unknown,
+/* b2-b4 */ "Search data low(12)", "Set limits(12)",
+            "Read element status attached",
+/* b5-b6 */ "Request volume element address", "Send volume tag, set streaming",
+/* b7-b9 */ "Read defect data(12)", "Read element status", "Read CD msf",
+/* ba-bc */ "Redundancy group (in), Scan",
+            "Redundancy group (out), Set cd-rom speed", "Spare (in), Play cd",
+/* bd-bf */ "Spare (out), Mechanism status", "Volume set (in), Read cd",
+            "Volume set (out), Send DVD structure",
 };
 
 

drivers/scsi/scsi.c

@@ -914,9 +914,7 @@ void scsi_device_put(struct scsi_device *sdev)
 		return;
 
 	module_put(sdev->host->hostt->module);
-	if (atomic_dec_and_test(&sdev->access_count))
-		if (test_bit(SDEV_DEL, &sdev->sdev_state))
-			device_del(&sdev->sdev_gendev);
+	atomic_dec(&sdev->access_count);
 	put_device(&sdev->sdev_gendev);
 	class_put(&sdev_class);
 }

drivers/scsi/scsi_devinfo.c

@@ -6,10 +6,11 @@
 #include <linux/moduleparam.h>
 #include <linux/proc_fs.h>
 #include <linux/seq_file.h>
+#include <scsi/scsi_devinfo.h>
 
 #include "scsi.h"
+#include "hosts.h"
 #include "scsi_priv.h"
-#include "scsi_devinfo.h"
 
 /*
  * scsi_dev_info_list: structure to hold black/white listed devices.
@@ -322,11 +323,17 @@ static int scsi_dev_info_list_add_str(char *dev_list)
  * Description:
  *     Search the scsi_dev_info_list for an entry matching @vendor and
  *     @model, if found, return the matching flags value, else return
- *     scsi_default_dev_flags.
+ *     the host or global default settings.
  **/
-int scsi_get_device_flags(unsigned char *vendor, unsigned char *model)
+int scsi_get_device_flags(struct scsi_device *sdev, unsigned char *vendor,
+			  unsigned char *model)
 {
 	struct scsi_dev_info_list *devinfo;
+	unsigned int bflags;
+
+	bflags = sdev->host->hostt->flags;
+	if (!bflags)
+		bflags = scsi_default_dev_flags;
 
 	list_for_each_entry(devinfo, &scsi_dev_info_list, dev_info_list) {
 		if (devinfo->compatible) {
@@ -378,7 +385,7 @@ int scsi_get_device_flags(unsigned char *vendor, unsigned char *model)
 				return devinfo->flags;
 		}
 	}
-	return scsi_default_dev_flags;
+	return bflags;
 }
 
 #ifdef CONFIG_SCSI_PROC_FS

drivers/scsi/scsi_priv.h

@@ -85,7 +85,8 @@ extern void scsi_init_cmd_from_req(struct scsi_cmnd *cmd,
 extern void __scsi_release_request(struct scsi_request *sreq);
 
 /* scsi_devinfo.c */
-extern int scsi_get_device_flags(unsigned char *vendor, unsigned char *model);
+extern int scsi_get_device_flags(struct scsi_device *sdev,
+				 unsigned char *vendor, unsigned char *model);
 extern int scsi_init_devinfo(void);
 extern void scsi_exit_devinfo(void);
 

drivers/scsi/scsi_scan.c

@@ -35,10 +35,10 @@
 #include "scsi.h"
 #include "hosts.h"
 #include <scsi/scsi_driver.h>
+#include <scsi/scsi_devinfo.h>
 
 #include "scsi_priv.h"
 #include "scsi_logging.h"
-#include "scsi_devinfo.h"
 
 #define ALLOC_FAILURE_MSG	KERN_ERR "%s: Allocation failure during" \
 	" SCSI scanning, some SCSI devices might not be configured\n"
@@ -365,7 +365,7 @@ static void scsi_probe_lun(struct scsi_request *sreq, char *inq_result,
 	 * bit fields in Scsi_Device, so bflags need not be passed as an
 	 * argument.
 	 */
-	*bflags |= scsi_get_device_flags(&inq_result[8], &inq_result[16]);
+	*bflags |= scsi_get_device_flags(sdev, &inq_result[8], &inq_result[16]);
 
 	possible_inq_resp_len = (unsigned char) inq_result[4] + 5;
 	if (BLIST_INQUIRY_36 & *bflags)
@@ -625,7 +625,15 @@ static int scsi_add_lun(struct scsi_device *sdev, char *inq_result, int *bflags)
 	sdev->max_device_blocked = SCSI_DEFAULT_DEVICE_BLOCKED;
 
 	sdev->use_10_for_rw = 1;
-	sdev->use_10_for_ms = 0;
+
+	if (*bflags & BLIST_MS_SKIP_PAGE_08)
+		sdev->skip_ms_page_8 = 1;
+
+	if (*bflags & BLIST_MS_SKIP_PAGE_3F)
+		sdev->skip_ms_page_3f = 1;
+
+	if (*bflags & BLIST_USE_10_BYTE_MS)
+		sdev->use_10_for_ms = 1;
 
 	if(sdev->host->hostt->slave_configure)
 		sdev->host->hostt->slave_configure(sdev);
@@ -678,7 +686,8 @@ static int scsi_probe_and_add_lun(struct Scsi_Host *host,
 			if (sdevp)
 				*sdevp = sdev;
 			if (bflagsp)
-				*bflagsp = scsi_get_device_flags(sdev->vendor,
+				*bflagsp = scsi_get_device_flags(sdev,
+								 sdev->vendor,
 								 sdev->model);
 			return SCSI_SCAN_LUN_PRESENT;
 		}
@@ -1080,8 +1089,12 @@ struct scsi_device *scsi_add_device(struct Scsi_Host *shost,
 
 void scsi_rescan_device(struct device *dev)
 {
-	struct scsi_driver *drv = to_scsi_driver(dev->driver);
+	struct scsi_driver *drv;
+	
+	if (!dev->driver)
+		return;
 
+	drv = to_scsi_driver(dev->driver);
 	if (try_module_get(drv->owner)) {
 		if (drv->rescan)
 			drv->rescan(dev);

drivers/scsi/scsi_sysfs.c

@@ -412,8 +412,7 @@ void scsi_remove_device(struct scsi_device *sdev)
 		set_bit(SDEV_DEL, &sdev->sdev_state);
 		if (sdev->host->hostt->slave_destroy)
 			sdev->host->hostt->slave_destroy(sdev);
-		if (!atomic_read(&sdev->access_count))
-			device_del(&sdev->sdev_gendev);
+		device_del(&sdev->sdev_gendev);
 		up_write(&class->subsys.rwsem);
 	}
 

drivers/scsi/sd.c

@@ -74,9 +74,16 @@
  */
 #define SD_MAX_RETRIES		5
 
+static void scsi_disk_release (struct kobject *kobj);
+
+static struct kobj_type scsi_disk_kobj_type = {
+	.release = scsi_disk_release,
+};
+
 struct scsi_disk {
 	struct scsi_driver *driver;	/* always &sd_template */
 	struct scsi_device *device;
+	struct kobject	kobj;
 	struct gendisk	*disk;
 	unsigned int	openers;	/* protected by BKL for now, yuck */
 	sector_t	capacity;	/* size in 512-byte sectors */
@@ -87,6 +94,7 @@ struct scsi_disk {
 	unsigned	RCD : 1;	/* state of disk RCD bit, unused */
 };
 
+
 static unsigned long sd_index_bits[SD_DISKS / BITS_PER_LONG];
 static spinlock_t sd_index_lock = SPIN_LOCK_UNLOCKED;
 
@@ -128,11 +136,33 @@ static int sd_major(int major_idx)
 	}
 }
 
+#define to_scsi_disk(obj) container_of(obj,struct scsi_disk,kobj);
+
 static inline struct scsi_disk *scsi_disk(struct gendisk *disk)
 {
 	return container_of(disk->private_data, struct scsi_disk, driver);
 }
 
+static int scsi_disk_get(struct scsi_disk *sdkp)
+{
+	if (!kobject_get(&sdkp->kobj))
+		goto out;
+	if (scsi_device_get(sdkp->device))
+		goto out_put_kobj;
+	return 0;
+
+out_put_kobj:
+	kobject_put(&sdkp->kobj);
+out:
+	return -ENXIO;
+}
+
+static void scsi_disk_put(struct scsi_disk *sdkp)
+{
+	scsi_device_put(sdkp->device);
+	kobject_put(&sdkp->kobj);
+}
+
 /**
  *	sd_init_command - build a scsi (read or write) command from
  *	information in the request structure.
@@ -352,15 +382,17 @@ static int sd_open(struct inode *inode, struct file *filp)
 {
 	struct gendisk *disk = inode->i_bdev->bd_disk;
 	struct scsi_disk *sdkp = scsi_disk(disk);
-	struct scsi_device *sdev = sdkp->device;
+	struct scsi_device *sdev;
 	int retval;
 
 	SCSI_LOG_HLQUEUE(3, printk("sd_open: disk=%s\n", disk->disk_name));
 
-	retval = scsi_device_get(sdev);
+	retval = scsi_disk_get(sdkp);
 	if (retval)
 		return retval;
 
+	sdev = sdkp->device;
+
 	/*
 	 * If the device is in error recovery, wait until it is done.
 	 * If the device is offline, then disallow any access to it.
@@ -406,7 +438,7 @@ static int sd_open(struct inode *inode, struct file *filp)
 	return 0;
 
 error_out:
-	scsi_device_put(sdev);
+	scsi_disk_put(sdkp);
 	return retval;	
 }
 
@@ -438,7 +470,7 @@ static int sd_release(struct inode *inode, struct file *filp)
 	 * XXX and what if there are packets in flight and this close()
 	 * XXX is followed by a "rmmod sd_mod"?
 	 */
-	scsi_device_put(sdev);
+	scsi_disk_put(sdkp);
 	return 0;
 }
 
@@ -1057,6 +1089,11 @@ sd_read_write_protect_flag(struct scsi_disk *sdkp, char *diskname,
 	int res;
 	struct scsi_mode_data data;
 
+	if (sdkp->device->skip_ms_page_3f) {
+		printk(KERN_NOTICE "%s: assuming Write Enabled\n", diskname);
+		return;
+	}
+
 	/*
 	 * First attempt: ask for all pages (0x3F), but only 4 bytes.
 	 * We have to start carefully: some devices hang if we ask
@@ -1103,6 +1140,8 @@ sd_read_cache_type(struct scsi_disk *sdkp, char *diskname,
 	const int modepage = 0x08; /* current values, cache page */
 	struct scsi_mode_data data;
 
+	if (sdkp->device->skip_ms_page_8)
+		goto defaults;
 
 	/* cautiously ask */
 	res = sd_do_mode_sense(SRpnt, dbd, modepage, buffer, 4, &data);
@@ -1160,6 +1199,8 @@ sd_read_cache_type(struct scsi_disk *sdkp, char *diskname,
 		printk(KERN_ERR "%s: asking for cache data failed\n",
 		       diskname);
 	}
+
+defaults:
 	printk(KERN_ERR "%s: assuming drive cache: write through\n",
 	       diskname);
 	sdkp->WCE = 0;
@@ -1270,6 +1311,10 @@ static int sd_probe(struct device *dev)
 	if (!sdkp)
 		goto out;
 
+	memset (sdkp, 0, sizeof(*sdkp));
+	kobject_init(&sdkp->kobj);
+	sdkp->kobj.ktype = &scsi_disk_kobj_type;
+
 	gd = alloc_disk(16);
 	if (!gd)
 		goto out_free;
@@ -1348,16 +1393,27 @@ static int sd_remove(struct device *dev)
 	struct scsi_disk *sdkp = dev_get_drvdata(dev);
 
 	del_gendisk(sdkp->disk);
+	sd_shutdown(dev);
+	kobject_put(&sdkp->kobj);
+
+	return 0;
+}
+
+/**
+ *	scsi_disk_release - Called to free the scsi_disk structure
+ *	@kobj: pointer to embedded kobject
+ **/
+static void scsi_disk_release(struct kobject *kobj)
+{
+	struct scsi_disk *sdkp = to_scsi_disk(kobj);
+	
+	put_disk(sdkp->disk);
 
 	spin_lock(&sd_index_lock);
 	clear_bit(sdkp->index, sd_index_bits);
 	spin_unlock(&sd_index_lock);
 
-	sd_shutdown(dev);
-	put_disk(sdkp->disk);
 	kfree(sdkp);
-
-	return 0;
 }
 
 /*

drivers/scsi/sg.c

@@ -877,6 +877,8 @@ sg_ioctl(struct inode *inode, struct file *filp,
 		result = get_user(val, (int *) arg);
 		if (result)
 			return result;
+		if (val < 0)
+			return -EINVAL;
 		if (val != sfp->reserve.bufflen) {
 			if (sg_res_in_use(sfp) || sfp->mmap_called)
 				return -EBUSY;

drivers/usb/storage/scsiglue.c

@@ -51,6 +51,7 @@
 
 #include <linux/slab.h>
 #include <linux/module.h>
+#include <scsi/scsi_devinfo.h>
 
 
 /***********************************************************************
@@ -64,10 +65,6 @@ static const char* host_info(struct Scsi_Host *host)
 
 static int slave_configure (struct scsi_device *sdev)
 {
-	/* set device to use 10-byte commands where possible */
-	sdev->use_10_for_ms = 1;
-	sdev->use_10_for_rw = 1;
-
 	/* this is to satisify the compiler, tho I don't think the 
 	 * return code is ever checked anywhere. */
 	return 0;
@@ -324,6 +321,9 @@ struct scsi_host_template usb_stor_host_template = {
 	/* emulated HBA */
 	.emulated =			TRUE,
 
+	/* modify scsi_device bits on probe */
+	.flags = (BLIST_MS_SKIP_PAGE_08 | BLIST_USE_10_BYTE_MS),
+
 	/* module management */
 	.module =			THIS_MODULE
 };

include/scsi/scsi_device.h

@@ -86,6 +86,8 @@ struct scsi_device {
 				     * because we did a bus reset. */
 	unsigned use_10_for_rw:1; /* first try 10-byte read / write */
 	unsigned use_10_for_ms:1; /* first try 10-byte mode sense/select */
+	unsigned skip_ms_page_8:1;	/* do not use MODE SENSE page 0x08 */
+	unsigned skip_ms_page_3f:1;	/* do not use MODE SENSE page 0x3f */
 	unsigned no_start_on_add:1;	/* do not issue start on add */
 
 	unsigned int device_blocked;	/* Device returned QUEUE_FULL. */

drivers/scsi/scsi_devinfo.h → include/scsi/scsi_devinfo.h

-
+#ifndef _SCSI_SCSI_DEVINFO_H
+#define _SCSI_SCSI_DEVINFO_H
 /*
  * Flags for SCSI devices that need special treatment
  */
@@ -14,4 +15,8 @@
 #define BLIST_LARGELUN		0x200	/* LUNs past 7 on a SCSI-2 device */
 #define BLIST_INQUIRY_36	0x400	/* override additional length field */
 #define BLIST_INQUIRY_58	0x800	/* ... for broken inquiry responses */
-#define BLIST_NOSTARTONADD      0x1000  /* do not do automatic start on add */
+#define BLIST_NOSTARTONADD	0x1000	/* do not do automatic start on add */
+#define BLIST_MS_SKIP_PAGE_08	0x2000	/* do not send ms page 0x08 */
+#define BLIST_MS_SKIP_PAGE_3F	0x4000	/* do not send ms page 0x3f */
+#define BLIST_USE_10_BYTE_MS	0x8000	/* use 10 byte ms before 6 byte ms */
+#endif

include/scsi/scsi_host.h

@@ -344,6 +344,12 @@ struct scsi_host_template {
 	 * module_init/module_exit.
 	 */
 	struct list_head legacy_hosts;
+
+	/*
+	 * Default flags settings, these modify the setting of scsi_device
+	 * bits.
+	 */
+	unsigned int flags;
 };
 
 /*