Commit 4e31e857 authored by Marijn Suijten's avatar Marijn Suijten Committed by Bjorn Andersson

arm64: dts: qcom: sm6125: Improve indentation of multiline properties

Some multiline properties (spread out over multiple lines to keep length
in check) were not indented properly, leading to misalignment with the
items above.  The DT file is still small enough to address this early in
the process.
Signed-off-by: default avatarMarijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: default avatarMartin Botka <martin.botka@somainline.org>
Signed-off-by: default avatarBjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210925141841.407257-1-marijn.suijten@somainline.org
parent b30cad26
......@@ -326,8 +326,8 @@ tcsr_mutex: hwlock@340000 {
tlmm: pinctrl@500000 {
compatible = "qcom,sm6125-tlmm";
reg = <0x00500000 0x400000>,
<0x00900000 0x400000>,
<0x00d00000 0x400000>;
<0x00900000 0x400000>,
<0x00d00000 0x400000>;
reg-names = "west", "south", "east";
interrupts = <GIC_SPI 227 IRQ_TYPE_LEVEL_HIGH>;
gpio-controller;
......@@ -391,12 +391,12 @@ sdhc_1: sdhci@4744000 {
reg-names = "hc", "core";
interrupts = <GIC_SPI 348 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 352 IRQ_TYPE_LEVEL_HIGH>;
<GIC_SPI 352 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "hc_irq", "pwr_irq";
clocks = <&gcc GCC_SDCC1_AHB_CLK>,
<&gcc GCC_SDCC1_APPS_CLK>,
<&xo_board>;
<&gcc GCC_SDCC1_APPS_CLK>,
<&xo_board>;
clock-names = "iface", "core", "xo";
bus-width = <8>;
non-removable;
......@@ -409,12 +409,12 @@ sdhc_2: sdhci@4784000 {
reg-names = "hc";
interrupts = <GIC_SPI 350 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
<GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "hc_irq", "pwr_irq";
clocks = <&gcc GCC_SDCC2_AHB_CLK>,
<&gcc GCC_SDCC2_APPS_CLK>,
<&xo_board>;
<&gcc GCC_SDCC2_APPS_CLK>,
<&xo_board>;
clock-names = "iface", "core", "xo";
pinctrl-0 = <&sdc2_state_on>;
......@@ -433,11 +433,11 @@ usb3: usb@4ef8800 {
ranges;
clocks = <&gcc GCC_USB30_PRIM_MASTER_CLK>,
<&gcc GCC_SYS_NOC_USB3_PRIM_AXI_CLK>,
<&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
<&gcc GCC_USB3_PRIM_CLKREF_CLK>,
<&gcc GCC_USB30_PRIM_SLEEP_CLK>,
<&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>;
<&gcc GCC_SYS_NOC_USB3_PRIM_AXI_CLK>,
<&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
<&gcc GCC_USB3_PRIM_CLKREF_CLK>,
<&gcc GCC_USB30_PRIM_SLEEP_CLK>,
<&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>;
assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
<&gcc GCC_USB30_PRIM_MASTER_CLK>;
......@@ -462,11 +462,11 @@ usb3_dwc3: usb@4e00000 {
spmi_bus: spmi@1c40000 {
compatible = "qcom,spmi-pmic-arb";
reg = <0x01c40000 0x1100>,
<0x01e00000 0x2000000>,
<0x03e00000 0x100000>,
<0x03f00000 0xa0000>,
<0x01c0a000 0x26000>;
reg = <0x01c40000 0x1100>,
<0x01e00000 0x2000000>,
<0x03e00000 0x100000>,
<0x03f00000 0xa0000>,
<0x01c0a000 0x26000>;
reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
interrupt-names = "periph_irq";
interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>;
......@@ -497,7 +497,7 @@ timer@f120000 {
frame@f121000 {
frame-number = <0>;
interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
<GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
reg = <0x0f121000 0x1000>,
<0x0f122000 0x1000>;
};
......@@ -548,7 +548,7 @@ frame@f128000 {
intc: interrupt-controller@f200000 {
compatible = "arm,gic-v3";
reg = <0x0f200000 0x20000>,
<0x0f300000 0x100000>;
<0x0f300000 0x100000>;
#interrupt-cells = <3>;
interrupt-controller;
interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
......@@ -558,9 +558,9 @@ intc: interrupt-controller@f200000 {
timer {
compatible = "arm,armv8-timer";
interrupts = <GIC_PPI 1 0xf08
GIC_PPI 2 0xf08
GIC_PPI 3 0xf08
GIC_PPI 0 0xf08>;
GIC_PPI 2 0xf08
GIC_PPI 3 0xf08
GIC_PPI 0 0xf08>;
clock-frequency = <19200000>;
};
};
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment