net: dsa: calculate the largest_mtu across all ports in the tree

If we have a cross-chip topology like this:

   sw0p0     sw0p1     sw0p2     sw0p3     sw0p4
[  cpu  ] [  user ] [  user ] [  dsa  ] [  user ]
                                  |
                                  +---------+
                                            |
   sw1p0     sw1p1     sw1p2     sw1p3     sw1p4
[  user ] [  user ] [  user ] [  dsa  ] [  dsa  ]

and we issue the following commands:

1. ip link set sw0p1 mtu 1700
2. ip link set sw1p1 mtu 1600

we notice the following happening:

Command 1. emits a non-targeted MTU notifier for the CPU port (sw0p0)
with the largest_mtu calculated across switch 0, of 1700. This matches
sw0p0, sw0p3 and sw1p4 (all CPU ports and DSA links).
Then, it emits a targeted MTU notifier for the user port (sw0p1), again
with MTU 1700 (this doesn't matter).

Command 2. emits a non-targeted MTU notifier for the CPU port (sw0p0)
with the largest_mtu calculated across switch 1, of 1600. This matches
the same group of ports as above, and decreases the MTU for the CPU port
and the DSA links from 1700 to 1600.

As a result, the sw0p1 user port can no longer communicate with its CPU
port at MTU 1700.

To address this, we should calculate the largest_mtu across all switches
that may share a CPU port, and only emit MTU notifiers with that value.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/dsa/slave.c

@@ -1528,6 +1528,7 @@ int dsa_slave_change_mtu(struct net_device *dev, int new_mtu)
 	struct dsa_port *dp = dsa_slave_to_port(dev);
 	struct dsa_slave_priv *p = netdev_priv(dev);
 	struct dsa_switch *ds = p->dp->ds;
+	struct dsa_port *dp_iter;
 	struct dsa_port *cpu_dp;
 	int port = p->dp->index;
 	int largest_mtu = 0;
@@ -1535,31 +1536,31 @@ int dsa_slave_change_mtu(struct net_device *dev, int new_mtu)
 	int old_master_mtu;
 	int mtu_limit;
 	int cpu_mtu;
-	int err, i;
+	int err;
 
 	if (!ds->ops->port_change_mtu)
 		return -EOPNOTSUPP;
 
-	for (i = 0; i < ds->num_ports; i++) {
+	list_for_each_entry(dp_iter, &ds->dst->ports, list) {
 		int slave_mtu;
 
-		if (!dsa_is_user_port(ds, i))
+		if (!dsa_port_is_user(dp_iter))
 			continue;
 
 		/* During probe, this function will be called for each slave
 		 * device, while not all of them have been allocated. That's
 		 * ok, it doesn't change what the maximum is, so ignore it.
 		 */
-		if (!dsa_to_port(ds, i)->slave)
+		if (!dp_iter->slave)
 			continue;
 
 		/* Pretend that we already applied the setting, which we
 		 * actually haven't (still haven't done all integrity checks)
 		 */
-		if (i == port)
+		if (dp_iter == dp)
 			slave_mtu = new_mtu;
 		else
-			slave_mtu = dsa_to_port(ds, i)->slave->mtu;
+			slave_mtu = dp_iter->slave->mtu;
 
 		if (largest_mtu < slave_mtu)
 			largest_mtu = slave_mtu;