staging: sm750fb: Remove unnecessary blank lines.

Removed multiple blank lines, which are not required. This patch fixes
the following check patch issues:

CHECK: Please don't use multiple blank lines
Signed-off-by: Varsha Rao <rvarsha016@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/staging/sm750fb/ddk750_display.h

@@ -12,7 +12,6 @@
 #define PNL_2_PRI	((0 << PNL_2_OFFSET) | PNL_2_USAGE)
 #define PNL_2_SEC	((2 << PNL_2_OFFSET) | PNL_2_USAGE)
 
-
 /*
  * primary timing & plane enable bit
  *	1: 80000[8] & 80000[2] on
@@ -24,7 +23,6 @@
 #define PRI_TP_ON ((0x1 << PRI_TP_OFFSET) | PRI_TP_USAGE)
 #define PRI_TP_OFF ((0x0 << PRI_TP_OFFSET) | PRI_TP_USAGE)
 
-
 /*
  * panel sequency status
  *	80000[27:24]
@@ -66,7 +64,6 @@
 #define CRT_2_PRI ((0x0 << CRT_2_OFFSET) | CRT_2_USAGE)
 #define CRT_2_SEC ((0x2 << CRT_2_OFFSET) | CRT_2_USAGE)
 
-
 /*
  * DAC affect both DVI and DSUB
  *	4[20]
@@ -87,8 +84,6 @@
 #define DPMS_OFF ((3 << DPMS_OFFSET) | DPMS_USAGE)
 #define DPMS_ON ((0 << DPMS_OFFSET) | DPMS_USAGE)
 
-
-
 /*
  * LCD1 means panel path TFT1  & panel path DVI (so enable DAC)
  * CRT means crt path DSUB

drivers/staging/sm750fb/ddk750_dvi.c

@@ -5,7 +5,6 @@
 #include "ddk750_dvi.h"
 #include "ddk750_sii164.h"
 
-
 /*
  * This global variable contains all the supported driver and its corresponding
  * function API. Please set the function pointer to NULL whenever the function
@@ -30,7 +29,6 @@ static dvi_ctrl_device_t g_dcftSupportedDviController[] = {
 #endif
 };
 
-
 int dviInit(
 	unsigned char edgeSelect,
 	unsigned char busSelect,
@@ -56,5 +54,3 @@ int dviInit(
 }
 
 #endif
-
-

drivers/staging/sm750fb/ddk750_mode.c

@@ -71,8 +71,6 @@ static unsigned long displayControlAdjust_SM750LE(mode_parameter_t *pModeParam,
 	return dispControl;
 }
 
-
-
 /* only timing related registers will be  programed */
 static int programModeRegisters(mode_parameter_t *pModeParam,
 						struct pll_value *pll)
@@ -112,7 +110,6 @@ static int programModeRegisters(mode_parameter_t *pModeParam,
 			((pModeParam->vertical_sync_start - 1) &
 				CRT_VERTICAL_SYNC_START_MASK));
 
-
 		tmp = DISPLAY_CTRL_TIMING | DISPLAY_CTRL_PLANE;
 		if (pModeParam->vertical_sync_polarity)
 			tmp |= DISPLAY_CTRL_VSYNC_PHASE;
@@ -219,5 +216,3 @@ int ddk750_setModeTiming(mode_parameter_t *parm, clock_type_t clock)
 	programModeRegisters(parm, &pll);
 	return 0;
 }
-
-

drivers/staging/sm750fb/ddk750_mode.h

@@ -9,7 +9,6 @@ typedef enum _spolarity_t {
 }
 spolarity_t;
 
-
 typedef struct _mode_parameter_t {
 	/* Horizontal timing. */
 	unsigned long horizontal_total;
@@ -37,5 +36,4 @@ mode_parameter_t;
 
 int ddk750_setModeTiming(mode_parameter_t *, clock_type_t);
 
-
 #endif

drivers/staging/sm750fb/ddk750_power.c

@@ -24,7 +24,6 @@ static unsigned int get_power_mode(void)
 	return peek32(POWER_MODE_CTRL) & POWER_MODE_CTRL_MODE_MASK;
 }
 
-
 /*
  * SM50x can operate in one of three modes: 0, 1 or Sleep.
  * On hardware reset, power mode 0 is default.
@@ -80,8 +79,6 @@ void sm750_set_current_gate(unsigned int gate)
 		poke32(MODE0_GATE, gate);
 }
 
-
-
 /*
  * This function enable/disable the 2D engine.
  */
@@ -145,5 +142,3 @@ void sm750_enable_i2c(unsigned int enable)
 
 	sm750_set_current_gate(gate);
 }
-
-

drivers/staging/sm750fb/ddk750_power.h

@@ -38,5 +38,4 @@ void sm750_enable_gpio(unsigned int enable);
  */
 void sm750_enable_i2c(unsigned int enable);
 
-
 #endif

drivers/staging/sm750fb/ddk750_reg.h

@@ -532,7 +532,6 @@
 #define GPIO_INTERRUPT_STATUS_26                        BIT(17)
 #define GPIO_INTERRUPT_STATUS_25                        BIT(16)
 
-
 #define PANEL_DISPLAY_CTRL                            0x080000
 #define PANEL_DISPLAY_CTRL_RESERVED_MASK              0xc0f08000
 #define PANEL_DISPLAY_CTRL_SELECT_SHIFT               28
@@ -1279,7 +1278,6 @@
 #define I2C_DATA14                                      0x010052
 #define I2C_DATA15                                      0x010053
 
-
 #define ZV0_CAPTURE_CTRL                                0x090000
 #define ZV0_CAPTURE_CTRL_FIELD_INPUT                    BIT(27)
 #define ZV0_CAPTURE_CTRL_SCAN                           BIT(26)
@@ -1445,7 +1443,6 @@
 #define DEFAULT_I2C_SCL                     30
 #define DEFAULT_I2C_SDA                     31
 
-
 #define GPIO_DATA_SM750LE                               0x020018
 #define GPIO_DATA_SM750LE_1                             BIT(1)
 #define GPIO_DATA_SM750LE_0                             BIT(0)
@@ -1454,5 +1451,4 @@
 #define GPIO_DATA_DIRECTION_SM750LE_1                   BIT(1)
 #define GPIO_DATA_DIRECTION_SM750LE_0                   BIT(0)
 
-
 #endif