Blackfin arch: use new platform data interface of musb to replace old one

Signed-off-by: Bryan Wu <cooloney@kernel.org>

arch/blackfin/mach-bf527/boards/cm_bf527.c

@@ -43,9 +43,7 @@
 #include <linux/irq.h>
 #include <linux/interrupt.h>
 #include <linux/usb/sl811.h>
-#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
 #include <linux/usb/musb.h>
-#endif
 #include <asm/cplb.h>
 #include <asm/dma.h>
 #include <asm/bfin5xx_spi.h>
@@ -130,6 +128,16 @@ static struct resource musb_resources[] = {
 	},
 };
 
+static struct musb_hdrc_config musb_config = {
+	.multipoint	= 0,
+	.dyn_fifo	= 0,
+	.soft_con	= 1,
+	.dma		= 1,
+	.num_eps	= 7,
+	.dma_channels	= 7,
+	.gpio_vrsel	= GPIO_PF11,
+};
+
 static struct musb_hdrc_platform_data musb_plat = {
 #if defined(CONFIG_USB_MUSB_OTG)
 	.mode		= MUSB_OTG,
@@ -138,7 +146,7 @@ static struct musb_hdrc_platform_data musb_plat = {
 #elif defined(CONFIG_USB_GADGET_MUSB_HDRC)
 	.mode		= MUSB_PERIPHERAL,
 #endif
-	.multipoint	= 0,
+	.config		= &musb_config,
 };
 
 static u64 musb_dmamask = ~(u32)0;

arch/blackfin/mach-bf527/boards/ezkit.c

@@ -42,9 +42,7 @@
 #include <linux/irq.h>
 #include <linux/interrupt.h>
 #include <linux/usb/sl811.h>
-#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
 #include <linux/usb/musb.h>
-#endif
 #include <asm/cplb.h>
 #include <asm/dma.h>
 #include <asm/bfin5xx_spi.h>
@@ -129,6 +127,16 @@ static struct resource musb_resources[] = {
 	},
 };
 
+static struct musb_hdrc_config musb_config = {
+	.multipoint	= 0,
+	.dyn_fifo	= 0,
+	.soft_con	= 1,
+	.dma		= 1,
+	.num_eps	= 7,
+	.dma_channels	= 7,
+	.gpio_vrsel	= GPIO_PG13,
+};
+
 static struct musb_hdrc_platform_data musb_plat = {
 #if defined(CONFIG_USB_MUSB_OTG)
 	.mode		= MUSB_OTG,
@@ -137,7 +145,7 @@ static struct musb_hdrc_platform_data musb_plat = {
 #elif defined(CONFIG_USB_GADGET_MUSB_HDRC)
 	.mode		= MUSB_PERIPHERAL,
 #endif
-	.multipoint	= 0,
+	.config		= &musb_config,
 };
 
 static u64 musb_dmamask = ~(u32)0;

arch/blackfin/mach-bf548/boards/cm_bf548.c

@@ -36,9 +36,7 @@
 #include <linux/spi/flash.h>
 #include <linux/irq.h>
 #include <linux/interrupt.h>
-#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
 #include <linux/usb/musb.h>
-#endif
 #include <asm/bfin5xx_spi.h>
 #include <asm/cplb.h>
 #include <asm/dma.h>
@@ -268,6 +266,16 @@ static struct resource musb_resources[] = {
 	},
 };
 
+static struct musb_hdrc_config musb_config = {
+	.multipoint	= 0,
+	.dyn_fifo	= 0,
+	.soft_con	= 1,
+	.dma		= 1,
+	.num_eps	= 7,
+	.dma_channels	= 7,
+	.gpio_vrsel	= GPIO_PH6,
+};
+
 static struct musb_hdrc_platform_data musb_plat = {
 #if defined(CONFIG_USB_MUSB_OTG)
 	.mode		= MUSB_OTG,
@@ -276,7 +284,7 @@ static struct musb_hdrc_platform_data musb_plat = {
 #elif defined(CONFIG_USB_GADGET_MUSB_HDRC)
 	.mode		= MUSB_PERIPHERAL,
 #endif
-	.multipoint	= 0,
+	.config		= &musb_config,
 };
 
 static u64 musb_dmamask = ~(u32)0;

arch/blackfin/mach-bf548/boards/ezkit.c

@@ -38,9 +38,7 @@
 #include <linux/irq.h>
 #include <linux/i2c.h>
 #include <linux/interrupt.h>
-#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
 #include <linux/usb/musb.h>
-#endif
 #include <asm/bfin5xx_spi.h>
 #include <asm/cplb.h>
 #include <asm/dma.h>
@@ -314,6 +312,16 @@ static struct resource musb_resources[] = {
 	},
 };
 
+static struct musb_hdrc_config musb_config = {
+	.multipoint	= 0,
+	.dyn_fifo	= 0,
+	.soft_con	= 1,
+	.dma		= 1,
+	.num_eps	= 7,
+	.dma_channels	= 7,
+	.gpio_vrsel	= GPIO_PE7,
+};
+
 static struct musb_hdrc_platform_data musb_plat = {
 #if defined(CONFIG_USB_MUSB_OTG)
 	.mode		= MUSB_OTG,
@@ -322,7 +330,7 @@ static struct musb_hdrc_platform_data musb_plat = {
 #elif defined(CONFIG_USB_GADGET_MUSB_HDRC)
 	.mode		= MUSB_PERIPHERAL,
 #endif
-	.multipoint	= 0,
+	.config		= &musb_config,
 };
 
 static u64 musb_dmamask = ~(u32)0;