Commit 5232f801 authored by Harish Zunjarrao's avatar Harish Zunjarrao Committed by James Bottomley

[SCSI] qla4xxx: Added restore factory defaults support using BSG

This command will causes the firmware to update all
configurations to pre-defined factory default settings.
Signed-off-by: default avatarHarish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: default avatarVikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: default avatarMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: default avatarJames Bottomley <JBottomley@Parallels.com>
parent dfcf7775
......@@ -337,6 +337,50 @@ qla4xxx_update_nvram(struct bsg_job *bsg_job)
return rval;
}
static int
qla4xxx_restore_defaults(struct bsg_job *bsg_job)
{
struct Scsi_Host *host = iscsi_job_to_shost(bsg_job);
struct scsi_qla_host *ha = to_qla_host(host);
struct iscsi_bsg_request *bsg_req = bsg_job->request;
struct iscsi_bsg_reply *bsg_reply = bsg_job->reply;
uint32_t region = 0;
uint32_t field0 = 0;
uint32_t field1 = 0;
int rval = -EINVAL;
bsg_reply->reply_payload_rcv_len = 0;
if (unlikely(pci_channel_offline(ha->pdev)))
goto leave;
if (is_qla4010(ha))
goto leave;
if (ql4xxx_reset_active(ha)) {
ql4_printk(KERN_ERR, ha, "%s: reset active\n", __func__);
rval = -EBUSY;
goto leave;
}
region = bsg_req->rqst_data.h_vendor.vendor_cmd[1];
field0 = bsg_req->rqst_data.h_vendor.vendor_cmd[2];
field1 = bsg_req->rqst_data.h_vendor.vendor_cmd[3];
rval = qla4xxx_restore_factory_defaults(ha, region, field0, field1);
if (rval) {
ql4_printk(KERN_ERR, ha, "%s: set nvram failed\n", __func__);
bsg_reply->result = DID_ERROR << 16;
rval = -EIO;
} else
bsg_reply->result = DID_OK << 16;
bsg_job_done(bsg_job, bsg_reply->result,
bsg_reply->reply_payload_rcv_len);
leave:
return rval;
}
/**
* qla4xxx_process_vendor_specific - handle vendor specific bsg request
* @job: iscsi_bsg_job to handle
......@@ -364,6 +408,9 @@ int qla4xxx_process_vendor_specific(struct bsg_job *bsg_job)
case QLISCSI_VND_UPDATE_NVRAM:
return qla4xxx_update_nvram(bsg_job);
case QLISCSI_VND_RESTORE_DEFAULTS:
return qla4xxx_restore_defaults(bsg_job);
default:
ql4_printk(KERN_ERR, ha, "%s: invalid BSG vendor command: "
"0x%x\n", __func__, bsg_req->msgcode);
......
......@@ -13,5 +13,6 @@
#define QLISCSI_VND_GET_ACB_STATE 3
#define QLISCSI_VND_READ_NVRAM 4
#define QLISCSI_VND_UPDATE_NVRAM 5
#define QLISCSI_VND_RESTORE_DEFAULTS 6
#endif
......@@ -166,6 +166,9 @@ int qla4xxx_get_nvram(struct scsi_qla_host *ha, dma_addr_t nvram_dma,
uint32_t offset, uint32_t size);
int qla4xxx_set_nvram(struct scsi_qla_host *ha, dma_addr_t nvram_dma,
uint32_t offset, uint32_t size);
int qla4xxx_restore_factory_defaults(struct scsi_qla_host *ha,
uint32_t region, uint32_t field0,
uint32_t field1);
/* BSG Functions */
int qla4xxx_bsg_request(struct bsg_job *bsg_job);
......
......@@ -1744,3 +1744,29 @@ int qla4xxx_set_nvram(struct scsi_qla_host *ha, dma_addr_t nvram_dma,
}
return status;
}
int qla4xxx_restore_factory_defaults(struct scsi_qla_host *ha,
uint32_t region, uint32_t field0,
uint32_t field1)
{
int status = QLA_SUCCESS;
uint32_t mbox_cmd[MBOX_REG_COUNT];
uint32_t mbox_sts[MBOX_REG_COUNT];
memset(&mbox_cmd, 0, sizeof(mbox_cmd));
memset(&mbox_sts, 0, sizeof(mbox_sts));
mbox_cmd[0] = MBOX_CMD_RESTORE_FACTORY_DEFAULTS;
mbox_cmd[3] = region;
mbox_cmd[4] = field0;
mbox_cmd[5] = field1;
status = qla4xxx_mailbox_command(ha, MBOX_REG_COUNT, 3, &mbox_cmd[0],
&mbox_sts[0]);
if (status != QLA_SUCCESS) {
DEBUG2(ql4_printk(KERN_ERR, ha, "scsi%ld: %s: failed "
"status %04X\n", ha->host_no, __func__,
mbox_sts[0]));
}
return status;
}
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment