Commit 524a7f08 authored by Daniel Lezcano's avatar Daniel Lezcano

clocksource/drivers/bcm2835_timer: Convert init function to return error

The init functions do not return any error. They behave as the following:

 - panic, thus leading to a kernel crash while another timer may work and
   make the system boot up correctly

 or

 - print an error and let the caller unaware if the state of the system

Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.

Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: default avatarDaniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: default avatarEric Anholt <eric@anholt.net>
parent 802fa498
......@@ -80,19 +80,24 @@ static irqreturn_t bcm2835_time_interrupt(int irq, void *dev_id)
}
}
static void __init bcm2835_timer_init(struct device_node *node)
static int __init bcm2835_timer_init(struct device_node *node)
{
void __iomem *base;
u32 freq;
int irq;
int irq, ret;
struct bcm2835_timer *timer;
base = of_iomap(node, 0);
if (!base)
panic("Can't remap registers");
if (!base) {
pr_err("Can't remap registers");
return -ENXIO;
}
if (of_property_read_u32(node, "clock-frequency", &freq))
panic("Can't read clock-frequency");
ret = of_property_read_u32(node, "clock-frequency", &freq);
if (ret) {
pr_err("Can't read clock-frequency");
return ret;
}
system_clock = base + REG_COUNTER_LO;
sched_clock_register(bcm2835_sched_read, 32, freq);
......@@ -101,12 +106,16 @@ static void __init bcm2835_timer_init(struct device_node *node)
freq, 300, 32, clocksource_mmio_readl_up);
irq = irq_of_parse_and_map(node, DEFAULT_TIMER);
if (irq <= 0)
panic("Can't parse IRQ");
if (irq <= 0) {
pr_err("Can't parse IRQ");
return -EINVAL;
}
timer = kzalloc(sizeof(*timer), GFP_KERNEL);
if (!timer)
panic("Can't allocate timer struct\n");
if (!timer) {
pr_err("Can't allocate timer struct\n");
return -ENOMEM;
}
timer->control = base + REG_CONTROL;
timer->compare = base + REG_COMPARE(DEFAULT_TIMER);
......@@ -121,12 +130,17 @@ static void __init bcm2835_timer_init(struct device_node *node)
timer->act.dev_id = timer;
timer->act.handler = bcm2835_time_interrupt;
if (setup_irq(irq, &timer->act))
panic("Can't set up timer IRQ\n");
ret = setup_irq(irq, &timer->act);
if (ret) {
pr_err("Can't set up timer IRQ\n");
return ret;
}
clockevents_config_and_register(&timer->evt, freq, 0xf, 0xffffffff);
pr_info("bcm2835: system timer (irq = %d)\n", irq);
return 0;
}
CLOCKSOURCE_OF_DECLARE(bcm2835, "brcm,bcm2835-system-timer",
CLOCKSOURCE_OF_DECLARE_RET(bcm2835, "brcm,bcm2835-system-timer",
bcm2835_timer_init);
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment