Merge tag 'riscv-dt-fixes-for-v6.10-rc5+' of...

Merge tag 'riscv-dt-fixes-for-v6.10-rc5+' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into arm/fixes

RISC-V Devicetree fixes for v6.10-rc5+

T-Head:
Jisheng hasn't got enough time to look after the platform, so Drew
Fustini is going to take over.

StarFive:
A fix for a regulator voltage range that prevented using low performance
SD cards.

Canaan:
Cleanup for some "over eager" aliases for serial ports that did not
exist on some boards and I/O devices disabled on boards where they were
not actually in use.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

MAINTAINERS

@@ -19314,7 +19314,7 @@ F:	drivers/perf/riscv_pmu_legacy.c
 F:	drivers/perf/riscv_pmu_sbi.c
 
 RISC-V THEAD SoC SUPPORT
-M:	Jisheng Zhang <jszhang@kernel.org>
+M:	Drew Fustini <drew@pdp7.com>
 M:	Guo Ren <guoren@kernel.org>
 M:	Fu Wei <wefu@redhat.com>
 L:	linux-riscv@lists.infradead.org

arch/riscv/boot/dts/canaan/canaan_kd233.dts

@@ -15,6 +15,10 @@ / {
 	model = "Kendryte KD233";
 	compatible = "canaan,kendryte-kd233", "canaan,kendryte-k210";
 
+	aliases {
+		serial0 = &uarths0;
+	};
+
 	chosen {
 		bootargs = "earlycon console=ttySIF0";
 		stdout-path = "serial0:115200n8";
@@ -46,7 +50,6 @@ key {
 &fpioa {
 	pinctrl-0 = <&jtag_pinctrl>;
 	pinctrl-names = "default";
-	status = "okay";
 
 	jtag_pinctrl: jtag-pinmux {
 		pinmux = <K210_FPIOA(0, K210_PCF_JTAG_TCLK)>,
@@ -118,6 +121,7 @@ &i2s0 {
 	#sound-dai-cells = <1>;
 	pinctrl-0 = <&i2s0_pinctrl>;
 	pinctrl-names = "default";
+	status = "okay";
 };
 
 &spi0 {
@@ -125,6 +129,7 @@ &spi0 {
 	pinctrl-names = "default";
 	num-cs = <1>;
 	cs-gpios = <&gpio0 20 GPIO_ACTIVE_HIGH>;
+	status = "okay";
 
 	panel@0 {
 		compatible = "canaan,kd233-tft", "ilitek,ili9341";

arch/riscv/boot/dts/canaan/k210.dtsi

@@ -16,13 +16,6 @@ / {
 	#size-cells = <1>;
 	compatible = "canaan,kendryte-k210";
 
-	aliases {
-		serial0 = &uarths0;
-		serial1 = &uart1;
-		serial2 = &uart2;
-		serial3 = &uart3;
-	};
-
 	/*
 	 * The K210 has an sv39 MMU following the privileged specification v1.9.
 	 * Since this is a non-ratified draft specification, the kernel does not
@@ -137,6 +130,7 @@ uarths0: serial@38000000 {
 			reg = <0x38000000 0x1000>;
 			interrupts = <33>;
 			clocks = <&sysclk K210_CLK_CPU>;
+			status = "disabled";
 		};
 
 		gpio0: gpio-controller@38001000 {
@@ -152,6 +146,7 @@ gpio0: gpio-controller@38001000 {
 				     <62>, <63>, <64>, <65>;
 			gpio-controller;
 			ngpios = <32>;
+			status = "disabled";
 		};
 
 		dmac0: dma-controller@50000000 {
@@ -187,6 +182,7 @@ gpio1: gpio@50200000 {
 					 <&sysclk K210_CLK_GPIO>;
 				clock-names = "bus", "db";
 				resets = <&sysrst K210_RST_GPIO>;
+				status = "disabled";
 
 				gpio1_0: gpio-port@0 {
 					#gpio-cells = <2>;
@@ -214,6 +210,7 @@ uart1: serial@50210000 {
 				dsr-override;
 				cts-override;
 				ri-override;
+				status = "disabled";
 			};
 
 			uart2: serial@50220000 {
@@ -230,6 +227,7 @@ uart2: serial@50220000 {
 				dsr-override;
 				cts-override;
 				ri-override;
+				status = "disabled";
 			};
 
 			uart3: serial@50230000 {
@@ -246,6 +244,7 @@ uart3: serial@50230000 {
 				dsr-override;
 				cts-override;
 				ri-override;
+				status = "disabled";
 			};
 
 			spi2: spi@50240000 {
@@ -259,6 +258,7 @@ spi2: spi@50240000 {
 					 <&sysclk K210_CLK_APB0>;
 				clock-names = "ssi_clk", "pclk";
 				resets = <&sysrst K210_RST_SPI2>;
+				status = "disabled";
 			};
 
 			i2s0: i2s@50250000 {
@@ -268,6 +268,7 @@ i2s0: i2s@50250000 {
 				clocks = <&sysclk K210_CLK_I2S0>;
 				clock-names = "i2sclk";
 				resets = <&sysrst K210_RST_I2S0>;
+				status = "disabled";
 			};
 
 			i2s1: i2s@50260000 {
@@ -277,6 +278,7 @@ i2s1: i2s@50260000 {
 				clocks = <&sysclk K210_CLK_I2S1>;
 				clock-names = "i2sclk";
 				resets = <&sysrst K210_RST_I2S1>;
+				status = "disabled";
 			};
 
 			i2s2: i2s@50270000 {
@@ -286,6 +288,7 @@ i2s2: i2s@50270000 {
 				clocks = <&sysclk K210_CLK_I2S2>;
 				clock-names = "i2sclk";
 				resets = <&sysrst K210_RST_I2S2>;
+				status = "disabled";
 			};
 
 			i2c0: i2c@50280000 {
@@ -296,6 +299,7 @@ i2c0: i2c@50280000 {
 					 <&sysclk K210_CLK_APB0>;
 				clock-names = "ref", "pclk";
 				resets = <&sysrst K210_RST_I2C0>;
+				status = "disabled";
 			};
 
 			i2c1: i2c@50290000 {
@@ -306,6 +310,7 @@ i2c1: i2c@50290000 {
 					 <&sysclk K210_CLK_APB0>;
 				clock-names = "ref", "pclk";
 				resets = <&sysrst K210_RST_I2C1>;
+				status = "disabled";
 			};
 
 			i2c2: i2c@502a0000 {
@@ -316,6 +321,7 @@ i2c2: i2c@502a0000 {
 					 <&sysclk K210_CLK_APB0>;
 				clock-names = "ref", "pclk";
 				resets = <&sysrst K210_RST_I2C2>;
+				status = "disabled";
 			};
 
 			fpioa: pinmux@502b0000 {
@@ -464,6 +470,7 @@ spi0: spi@52000000 {
 				reset-names = "spi";
 				num-cs = <4>;
 				reg-io-width = <4>;
+				status = "disabled";
 			};
 
 			spi1: spi@53000000 {
@@ -479,6 +486,7 @@ spi1: spi@53000000 {
 				reset-names = "spi";
 				num-cs = <4>;
 				reg-io-width = <4>;
+				status = "disabled";
 			};
 
 			spi3: spi@54000000 {
@@ -495,6 +503,7 @@ spi3: spi@54000000 {
 
 				num-cs = <4>;
 				reg-io-width = <4>;
+				status = "disabled";
 			};
 		};
 	};

arch/riscv/boot/dts/canaan/k210_generic.dts

@@ -15,6 +15,10 @@ / {
 	model = "Kendryte K210 generic";
 	compatible = "canaan,kendryte-k210";
 
+	aliases {
+		serial0 = &uarths0;
+	};
+
 	chosen {
 		bootargs = "earlycon console=ttySIF0";
 		stdout-path = "serial0:115200n8";
@@ -24,7 +28,6 @@ chosen {
 &fpioa {
 	pinctrl-0 = <&jtag_pins>;
 	pinctrl-names = "default";
-	status = "okay";
 
 	jtag_pins: jtag-pinmux {
 		pinmux = <K210_FPIOA(0, K210_PCF_JTAG_TCLK)>,

arch/riscv/boot/dts/canaan/sipeed_maix_bit.dts

@@ -17,6 +17,10 @@ / {
 	compatible = "sipeed,maix-bit", "sipeed,maix-bitm",
 		     "canaan,kendryte-k210";
 
+	aliases {
+		serial0 = &uarths0;
+	};
+
 	chosen {
 		bootargs = "earlycon console=ttySIF0";
 		stdout-path = "serial0:115200n8";
@@ -58,7 +62,6 @@ key-boot {
 &fpioa {
 	pinctrl-names = "default";
 	pinctrl-0 = <&jtag_pinctrl>;
-	status = "okay";
 
 	jtag_pinctrl: jtag-pinmux {
 		pinmux = <K210_FPIOA(0, K210_PCF_JTAG_TCLK)>,
@@ -156,6 +159,7 @@ &i2s0 {
 	#sound-dai-cells = <1>;
 	pinctrl-0 = <&i2s0_pinctrl>;
 	pinctrl-names = "default";
+	status = "okay";
 };
 
 &i2c1 {
@@ -170,6 +174,7 @@ &spi0 {
 	pinctrl-names = "default";
 	num-cs = <1>;
 	cs-gpios = <&gpio0 20 GPIO_ACTIVE_HIGH>;
+	status = "okay";
 
 	panel@0 {
 		compatible = "sitronix,st7789v";
@@ -199,6 +204,8 @@ mmc@0 {
 };
 
 &spi3 {
+	status = "okay";
+
 	flash@0 {
 		compatible = "jedec,spi-nor";
 		reg = <0>;

arch/riscv/boot/dts/canaan/sipeed_maix_dock.dts

@@ -17,6 +17,10 @@ / {
 	compatible = "sipeed,maix-dock-m1", "sipeed,maix-dock-m1w",
 		     "canaan,kendryte-k210";
 
+	aliases {
+		serial0 = &uarths0;
+	};
+
 	chosen {
 		bootargs = "earlycon console=ttySIF0";
 		stdout-path = "serial0:115200n8";
@@ -63,7 +67,6 @@ key-boot {
 &fpioa {
 	pinctrl-0 = <&jtag_pinctrl>;
 	pinctrl-names = "default";
-	status = "okay";
 
 	jtag_pinctrl: jtag-pinmux {
 		pinmux = <K210_FPIOA(0, K210_PCF_JTAG_TCLK)>,
@@ -159,6 +162,7 @@ &i2s0 {
 	#sound-dai-cells = <1>;
 	pinctrl-0 = <&i2s0_pinctrl>;
 	pinctrl-names = "default";
+	status = "okay";
 };
 
 &i2c1 {
@@ -173,6 +177,7 @@ &spi0 {
 	pinctrl-names = "default";
 	num-cs = <1>;
 	cs-gpios = <&gpio0 20 GPIO_ACTIVE_HIGH>;
+	status = "okay";
 
 	panel@0 {
 		compatible = "sitronix,st7789v";

arch/riscv/boot/dts/canaan/sipeed_maix_go.dts

@@ -16,6 +16,10 @@ / {
 	model = "SiPeed MAIX GO";
 	compatible = "sipeed,maix-go", "canaan,kendryte-k210";
 
+	aliases {
+		serial0 = &uarths0;
+	};
+
 	chosen {
 		bootargs = "earlycon console=ttySIF0";
 		stdout-path = "serial0:115200n8";
@@ -69,7 +73,6 @@ key-down {
 &fpioa {
 	pinctrl-0 = <&jtag_pinctrl>;
 	pinctrl-names = "default";
-	status = "okay";
 
 	jtag_pinctrl: jtag-pinmux {
 		pinmux = <K210_FPIOA(0, K210_PCF_JTAG_TCLK)>,
@@ -167,6 +170,7 @@ &i2s0 {
 	#sound-dai-cells = <1>;
 	pinctrl-0 = <&i2s0_pinctrl>;
 	pinctrl-names = "default";
+	status = "okay";
 };
 
 &i2c1 {
@@ -181,6 +185,7 @@ &spi0 {
 	pinctrl-names = "default";
 	num-cs = <1>;
 	cs-gpios = <&gpio0 20 GPIO_ACTIVE_HIGH>;
+	status = "okay";
 
 	panel@0 {
 		compatible = "sitronix,st7789v";
@@ -209,6 +214,8 @@ mmc@0 {
 };
 
 &spi3 {
+	status = "okay";
+
 	flash@0 {
 		compatible = "jedec,spi-nor";
 		reg = <0>;

arch/riscv/boot/dts/canaan/sipeed_maixduino.dts

@@ -15,6 +15,10 @@ / {
 	model = "SiPeed MAIXDUINO";
 	compatible = "sipeed,maixduino", "canaan,kendryte-k210";
 
+	aliases {
+		serial0 = &uarths0;
+	};
+
 	chosen {
 		bootargs = "earlycon console=ttySIF0";
 		stdout-path = "serial0:115200n8";
@@ -39,8 +43,6 @@ vcc_3v3: regulator-3v3 {
 };
 
 &fpioa {
-	status = "okay";
-
 	uarths_pinctrl: uarths-pinmux {
 		pinmux = <K210_FPIOA(4, K210_PCF_UARTHS_RX)>, /* Header "0" */
 			 <K210_FPIOA(5, K210_PCF_UARTHS_TX)>; /* Header "1" */
@@ -132,6 +134,7 @@ &i2s0 {
 	#sound-dai-cells = <1>;
 	pinctrl-0 = <&i2s0_pinctrl>;
 	pinctrl-names = "default";
+	status = "okay";
 };
 
 &i2c1 {
@@ -146,6 +149,7 @@ &spi0 {
 	pinctrl-names = "default";
 	num-cs = <1>;
 	cs-gpios = <&gpio0 20 GPIO_ACTIVE_HIGH>;
+	status = "okay";
 
 	panel@0 {
 		compatible = "sitronix,st7789v";
@@ -174,6 +178,8 @@ mmc@0 {
 };
 
 &spi3 {
+	status = "okay";
+
 	flash@0 {
 		compatible = "jedec,spi-nor";
 		reg = <0>;

arch/riscv/boot/dts/starfive/jh7110-common.dtsi

@@ -244,7 +244,7 @@ emmc_vdd: aldo4 {
 				regulator-boot-on;
 				regulator-always-on;
 				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
 				regulator-name = "emmc_vdd";
 			};
 		};