drm/i915/skl: Set the eDP link rate on DPLL0

On SKL DPLL0 is used to derive CDCLK but can also be used to drive an
eDP port (as long as we don't want SSC). DPLL0 is special enough to not
be handled by the shared DPLL framework (drives CDCLK, not supposed to
enable the HDMI mode), So we need to compute the configuration
separately from the other DPLLs.

Note that we don't need to reprogram DPLL0 (which would mean bringing
down CDCLK) to support the various eDP 1.3 link rates as they all share
the same VCO (8100).
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drivers/gpu/drm/i915/intel_ddi.c

@@ -1484,6 +1484,25 @@ static void intel_ddi_pre_enable(struct intel_encoder *intel_encoder)
 		uint32_t dpll = crtc->config.ddi_pll_sel;
 		uint32_t val;
 
+		/*
+		 * DPLL0 is used for eDP and is the only "private" DPLL (as
+		 * opposed to shared) on SKL
+		 */
+		if (type == INTEL_OUTPUT_EDP) {
+			WARN_ON(dpll != SKL_DPLL0);
+
+			val = I915_READ(DPLL_CTRL1);
+
+			val &= ~(DPLL_CTRL1_HDMI_MODE(dpll) |
+				 DPLL_CTRL1_SSC(dpll) |
+				 DPLL_CRTL1_LINK_RATE_MASK(dpll));
+			val |= crtc->config.dpll_hw_state.ctrl1 << (dpll * 6);
+
+			I915_WRITE(DPLL_CTRL1, val);
+			POSTING_READ(DPLL_CTRL1);
+		}
+
+		/* DDI -> PLL mapping  */
 		val = I915_READ(DPLL_CTRL2);
 
 		val &= ~(DPLL_CTRL2_DDI_CLK_OFF(port) |
@@ -1492,6 +1511,7 @@ static void intel_ddi_pre_enable(struct intel_encoder *intel_encoder)
 			DPLL_CTRL2_DDI_SEL_OVERRIDE(port));
 
 		I915_WRITE(DPLL_CTRL2, val);
+
 	} else {
 		WARN_ON(crtc->config.ddi_pll_sel == PORT_CLK_SEL_NONE);
 		I915_WRITE(PORT_CLK_SEL(port), crtc->config.ddi_pll_sel);

drivers/gpu/drm/i915/intel_dp.c

@@ -1073,6 +1073,33 @@ intel_dp_connector_unregister(struct intel_connector *intel_connector)
 	intel_connector_unregister(intel_connector);
 }
 
+static void
+skl_edp_set_pll_config(struct intel_crtc_config *pipe_config, int link_bw)
+{
+	u32 ctrl1;
+
+	pipe_config->ddi_pll_sel = SKL_DPLL0;
+	pipe_config->dpll_hw_state.cfgcr1 = 0;
+	pipe_config->dpll_hw_state.cfgcr2 = 0;
+
+	ctrl1 = DPLL_CTRL1_OVERRIDE(SKL_DPLL0);
+	switch (link_bw) {
+	case DP_LINK_BW_1_62:
+		ctrl1 |= DPLL_CRTL1_LINK_RATE(DPLL_CRTL1_LINK_RATE_810,
+					      SKL_DPLL0);
+		break;
+	case DP_LINK_BW_2_7:
+		ctrl1 |= DPLL_CRTL1_LINK_RATE(DPLL_CRTL1_LINK_RATE_1350,
+					      SKL_DPLL0);
+		break;
+	case DP_LINK_BW_5_4:
+		ctrl1 |= DPLL_CRTL1_LINK_RATE(DPLL_CRTL1_LINK_RATE_2700,
+					      SKL_DPLL0);
+		break;
+	}
+	pipe_config->dpll_hw_state.ctrl1 = ctrl1;
+}
+
 static void
 hsw_dp_set_ddi_pll_sel(struct intel_crtc_config *pipe_config, int link_bw)
 {
@@ -1250,7 +1277,9 @@ intel_dp_compute_config(struct intel_encoder *encoder,
 				&pipe_config->dp_m2_n2);
 	}
 
-	if (IS_HASWELL(dev) || IS_BROADWELL(dev))
+	if (IS_SKYLAKE(dev) && is_edp(intel_dp))
+		skl_edp_set_pll_config(pipe_config, intel_dp->link_bw);
+	else if (IS_HASWELL(dev) || IS_BROADWELL(dev))
 		hsw_dp_set_ddi_pll_sel(pipe_config, intel_dp->link_bw);
 	else
 		intel_dp_set_clock(encoder, pipe_config, intel_dp->link_bw);