pwm: Remove obsolete HAVE_PWM Kconfig symbol

Before we had the PWM framework we used to have a barebone PWM api. The
HAVE_PWM Kconfig symbol used to be selected by the PWM drivers to specify
the PWM API is present in the kernel. Since the last legacy driver is gone
the HAVE_PWM symbol can go aswell.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-pwm@vger.kernel.orig
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

arch/arm/Kconfig

@@ -113,9 +113,6 @@ config ARM_DMA_IOMMU_ALIGNMENT
 
 endif
 
-config HAVE_PWM
-	bool
-
 config MIGHT_HAVE_PCI
 	bool
 
@@ -632,7 +629,6 @@ config ARCH_LPC32XX
 	select CPU_ARM926T
 	select GENERIC_CLOCKEVENTS
 	select HAVE_IDE
-	select HAVE_PWM
 	select USB_ARCH_HAS_OHCI
 	select USE_OF
 	help

arch/arm/mach-pxa/Kconfig

@@ -7,7 +7,6 @@ comment "Intel/Marvell Dev Platforms (sorted by hardware release time)"
 config MACH_PXA3XX_DT
 	bool "Support PXA3xx platforms from device tree"
 	select CPU_PXA300
-	select HAVE_PWM
 	select POWER_SUPPLY
 	select PXA3xx
 	select USE_OF
@@ -23,12 +22,10 @@ config ARCH_LUBBOCK
 
 config MACH_MAINSTONE
 	bool "Intel HCDDBBVA0 Development Platform (aka Mainstone)"
-	select HAVE_PWM
 	select PXA27x
 
 config MACH_ZYLONITE
 	bool
-	select HAVE_PWM
 	select PXA3xx
 
 config MACH_ZYLONITE300
@@ -69,7 +66,6 @@ config ARCH_PXA_IDP
 config ARCH_VIPER
 	bool "Arcom/Eurotech VIPER SBC"
 	select ARCOM_PCMCIA
-	select HAVE_PWM
 	select I2C_GPIO
 	select ISA
 	select PXA25x
@@ -120,7 +116,6 @@ config MACH_CM_X300
 	bool "CompuLab CM-X300 modules"
 	select CPU_PXA300
 	select CPU_PXA310
-	select HAVE_PWM
 	select PXA3xx
 
 config MACH_CAPC7117
@@ -211,7 +206,6 @@ config TRIZEPS_PCMCIA
 
 config MACH_LOGICPD_PXA270
 	bool "LogicPD PXA270 Card Engine Development Platform"
-	select HAVE_PWM
 	select PXA27x
 
 config MACH_PCM027
@@ -222,7 +216,6 @@ config MACH_PCM027
 config MACH_PCM990_BASEBOARD
 	bool "PHYTEC PCM-990 development board"
 	depends on MACH_PCM027
-	select HAVE_PWM
 
 choice
 	prompt "display on pcm990"
@@ -246,7 +239,6 @@ config MACH_COLIBRI
 config MACH_COLIBRI_PXA270_INCOME
 	bool "Income s.r.o. PXA270 SBC"
 	depends on MACH_COLIBRI
-	select HAVE_PWM
 	select PXA27x
 
 config MACH_COLIBRI300
@@ -275,7 +267,6 @@ comment "End-user Products (sorted by vendor name)"
 
 config MACH_H4700
 	bool "HP iPAQ hx4700"
-	select HAVE_PWM
 	select IWMMXT
 	select PXA27x
 
@@ -289,14 +280,12 @@ config MACH_HIMALAYA
 
 config MACH_MAGICIAN
 	bool "Enable HTC Magician Support"
-	select HAVE_PWM
 	select IWMMXT
 	select PXA27x
 
 config MACH_MIOA701
 	bool "Mitac Mio A701 Support"
 	select GPIO_SYSFS
-	select HAVE_PWM
 	select IWMMXT
 	select PXA27x
 	help
@@ -306,7 +295,6 @@ config MACH_MIOA701
 
 config PXA_EZX
 	bool "Motorola EZX Platform"
-	select HAVE_PWM
 	select IWMMXT
 	select PXA27x
 
@@ -346,7 +334,6 @@ config MACH_MP900C
 
 config ARCH_PXA_PALM
 	bool "PXA based Palm PDAs"
-	select HAVE_PWM
 
 config MACH_PALM27X
 	bool
@@ -444,7 +431,6 @@ config MACH_TREO680
 config MACH_RAUMFELD_RC
 	bool "Raumfeld Controller"
 	select CPU_PXA300
-	select HAVE_PWM
 	select POWER_SUPPLY
 	select PXA3xx
 
@@ -608,7 +594,6 @@ config MACH_E800
 
 config MACH_ZIPIT2
 	bool "Zipit Z2 Handheld"
-	select HAVE_PWM
 	select PXA27x
 endmenu
 

arch/mips/Kconfig

@@ -235,7 +235,6 @@ config MACH_JZ4740
 	select IRQ_CPU
 	select ARCH_REQUIRE_GPIOLIB
 	select SYS_HAS_EARLY_PRINTK
-	select HAVE_PWM
 	select HAVE_CLK
 	select GENERIC_IRQ_CHIP
 

drivers/input/misc/Kconfig

@@ -156,7 +156,7 @@ config INPUT_MAX8925_ONKEY
 
 config INPUT_MAX8997_HAPTIC
 	tristate "MAXIM MAX8997 haptic controller support"
-	depends on PWM && HAVE_PWM && MFD_MAX8997
+	depends on PWM && MFD_MAX8997
 	select INPUT_FF_MEMLESS
 	help
 	  This option enables device driver support for the haptic controller
@@ -470,7 +470,7 @@ config INPUT_PCF8574
 
 config INPUT_PWM_BEEPER
 	tristate "PWM beeper support"
-	depends on PWM && HAVE_PWM
+	depends on PWM
 	help
 	  Say Y here to get support for PWM based beeper devices.
 

include/linux/pwm.h

@@ -7,7 +7,7 @@
 struct pwm_device;
 struct seq_file;
 
-#if IS_ENABLED(CONFIG_PWM) || IS_ENABLED(CONFIG_HAVE_PWM)
+#if IS_ENABLED(CONFIG_PWM)
 /*
  * pwm_request - request a PWM device
  */