media: i2c: Drop unused s5k6aa camera sensor driver

The s5k6aa camera sensor driver doesn't support DT and relies on
platform data. The last board files supplying platform data for that
device have been removed from the kernel in v3.11. The driver hasn't
been used since them. Drop it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

Documentation/admin-guide/media/i2c-cardlist.rst

@@ -105,7 +105,6 @@ s5c73m3       Samsung S5C73M3 sensor
 s5k4ecgx      Samsung S5K4ECGX sensor
 s5k5baf       Samsung S5K5BAF sensor
 s5k6a3        Samsung S5K6A3 sensor
-s5k6aa        Samsung S5K6AAFX sensor
 sr030pc30     Siliconfile SR030PC30 sensor
 vs6624        ST VS6624 sensor
 ============  ==========================================================

drivers/media/i2c/Kconfig

@@ -784,15 +784,6 @@ config VIDEO_S5K6A3
 	  This is a V4L2 sensor driver for Samsung S5K6A3 raw
 	  camera sensor.
 
-config VIDEO_S5K6AA
-	tristate "Samsung S5K6AAFX sensor support"
-	depends on I2C && VIDEO_DEV
-	select MEDIA_CONTROLLER
-	select VIDEO_V4L2_SUBDEV_API
-	help
-	  This is a V4L2 sensor driver for Samsung S5K6AA(FX) 1.3M
-	  camera sensor with an embedded SoC image signal processor.
-
 config VIDEO_SR030PC30
 	tristate "Siliconfile SR030PC30 sensor support"
 	depends on I2C && VIDEO_DEV

drivers/media/i2c/Makefile

@@ -105,7 +105,6 @@ obj-$(CONFIG_VIDEO_RJ54N1) += rj54n1cb0c.o
 obj-$(CONFIG_VIDEO_S5C73M3) += s5c73m3/
 obj-$(CONFIG_VIDEO_S5K5BAF) += s5k5baf.o
 obj-$(CONFIG_VIDEO_S5K6A3) += s5k6a3.o
-obj-$(CONFIG_VIDEO_S5K6AA) += s5k6aa.o
 obj-$(CONFIG_VIDEO_SAA6588) += saa6588.o
 obj-$(CONFIG_VIDEO_SAA6752HS) += saa6752hs.o
 obj-$(CONFIG_VIDEO_SAA7110) += saa7110.o

include/media/i2c/s5k6aa.h

-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * S5K6AAFX camera sensor driver header
- *
- * Copyright (C) 2011 Samsung Electronics Co., Ltd.
- */
-
-#ifndef S5K6AA_H
-#define S5K6AA_H
-
-#include <media/v4l2-mediabus.h>
-
-/**
- * struct s5k6aa_gpio - data structure describing a GPIO
- * @gpio:  GPIO number
- * @level: indicates active state of the @gpio
- */
-struct s5k6aa_gpio {
-	int gpio;
-	int level;
-};
-
-/**
- * struct s5k6aa_platform_data - s5k6aa driver platform data
- * @set_power:   an additional callback to the board code, called
- *               after enabling the regulators and before switching
- *               the sensor off
- * @mclk_frequency: sensor's master clock frequency in Hz
- * @gpio_reset:  GPIO driving RESET pin
- * @gpio_stby:   GPIO driving STBY pin
- * @bus_type:    bus type
- * @nlanes:      maximum number of MIPI-CSI lanes used
- * @horiz_flip:  default horizontal image flip value, non zero to enable
- * @vert_flip:   default vertical image flip value, non zero to enable
- */
-
-struct s5k6aa_platform_data {
-	int (*set_power)(int enable);
-	unsigned long mclk_frequency;
-	struct s5k6aa_gpio gpio_reset;
-	struct s5k6aa_gpio gpio_stby;
-	enum v4l2_mbus_type bus_type;
-	u8 nlanes;
-	u8 horiz_flip;
-	u8 vert_flip;
-};
-
-#endif /* S5K6AA_H */