Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC fixes from Kevin Hilman:
 "Another round of fixes from arm-soc land, which are mostly DT fixes
  for:

   - OMAP: handful of DT fixes devices on newly supported hardware
   - davinci: fix 2nd EDMA channel
   - ux500: extend previous pinctrl fix to another board
   - at91: clock registration fixes, compatibility string precision

  And one more fix for event cleanup in drivers/bus/arm-ccn"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  bus: arm-ccn: Move event cleanup routine
  ARM: at91/dt: rm9200: fix usb clock definition
  ARM: at91: rm9200: fix clock registration
  ARM: at91/dt: sam9g20: set at91sam9g20 pllb driver
  ARM: dts: dra7-evm: Add vtt regulator support
  ARM: dts: dra7-evm: Fix spi1 mux documentation
  ARM: dts: am43x-epos-evm: Disable QSPI to prevent conflict with GPMC-NAND
  ARM: OMAP2+: gpmc: Don't complain if wait pin is used without r/w monitoring
  ARM: dts: am43xx-epos-evm: Don't use read/write wait monitoring
  ARM: dts: am437x-gp-evm: Don't use read/write wait monitoring
  ARM: dts: am437x-gp-evm: Use BCH16 ECC scheme instead of BCH8
  ARM: dts: am43x-epos-evm: Use BCH16 ECC scheme instead of BCH8
  ARM: dts: am4372: fix USB regs size
  ARM: dts: am437x-gp: switch i2c0 to 100KHz
  ARM: dts: dra7-evm: Fix 8th NAND partition's name
  ARM: dts: dra7-evm: Fix i2c3 pinmux and frequency
  ARM: ux500: disable msp2 node on Snowball
  ARM: edma: Fix configuration parsing for SoCs with multiple eDMA3 CC
  ARM: dts: set 'ti,set-rate-parent' for dpll4_m5x2 clock

arch/arm/boot/dts/am4372.dtsi

@@ -804,7 +804,7 @@ dwc3_1: omap_dwc3@48380000 {
 
 			usb1: usb@48390000 {
 				compatible = "synopsys,dwc3";
-				reg = <0x48390000 0x17000>;
+				reg = <0x48390000 0x10000>;
 				interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
 				phys = <&usb2_phy1>;
 				phy-names = "usb2-phy";
@@ -826,7 +826,7 @@ dwc3_2: omap_dwc3@483c0000 {
 
 			usb2: usb@483d0000 {
 				compatible = "synopsys,dwc3";
-				reg = <0x483d0000 0x17000>;
+				reg = <0x483d0000 0x10000>;
 				interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
 				phys = <&usb2_phy2>;
 				phy-names = "usb2-phy";

arch/arm/boot/dts/am437x-gp-evm.dts

@@ -260,7 +260,7 @@ &i2c0 {
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c0_pins>;
-	clock-frequency = <400000>;
+	clock-frequency = <100000>;
 
 	tps65218: tps65218@24 {
 		reg = <0x24>;
@@ -424,7 +424,7 @@ &gpmc {
 	ranges = <0 0 0 0x01000000>;	/* minimum GPMC partition = 16MB */
 	nand@0,0 {
 		reg = <0 0 4>;		/* device IO registers */
-		ti,nand-ecc-opt = "bch8";
+		ti,nand-ecc-opt = "bch16";
 		ti,elm-id = <&elm>;
 		nand-bus-width = <8>;
 		gpmc,device-width = <1>;
@@ -443,8 +443,6 @@ nand@0,0 {
 		gpmc,rd-cycle-ns = <40>;
 		gpmc,wr-cycle-ns = <40>;
 		gpmc,wait-pin = <0>;
-		gpmc,wait-on-read;
-		gpmc,wait-on-write;
 		gpmc,bus-turnaround-ns = <0>;
 		gpmc,cycle2cycle-delay-ns = <0>;
 		gpmc,clk-activation-ns = <0>;

arch/arm/boot/dts/am43x-epos-evm.dts

@@ -435,13 +435,13 @@ &elm {
 };
 
 &gpmc {
-	status = "okay";
+	status = "okay";	/* Disable QSPI when enabling GPMC (NAND) */
 	pinctrl-names = "default";
 	pinctrl-0 = <&nand_flash_x8>;
 	ranges = <0 0 0x08000000 0x10000000>;	/* CS0: NAND */
 	nand@0,0 {
 		reg = <0 0 0>; /* CS0, offset 0 */
-		ti,nand-ecc-opt = "bch8";
+		ti,nand-ecc-opt = "bch16";
 		ti,elm-id = <&elm>;
 		nand-bus-width = <8>;
 		gpmc,device-width = <1>;
@@ -459,8 +459,7 @@ nand@0,0 {
 		gpmc,access-ns = <30>; /* tCEA + 4*/
 		gpmc,rd-cycle-ns = <40>;
 		gpmc,wr-cycle-ns = <40>;
-		gpmc,wait-on-read = "true";
-		gpmc,wait-on-write = "true";
+		gpmc,wait-pin = <0>;
 		gpmc,bus-turnaround-ns = <0>;
 		gpmc,cycle2cycle-delay-ns = <0>;
 		gpmc,clk-activation-ns = <0>;
@@ -557,7 +556,7 @@ &usb2 {
 };
 
 &qspi {
-	status = "okay";
+	status = "disabled";	/* Disable GPMC (NAND) when enabling QSPI */
 	pinctrl-names = "default";
 	pinctrl-0 = <&qspi1_default>;
 

arch/arm/boot/dts/at91rm9200.dtsi

@@ -149,7 +149,7 @@ mck: masterck {
 				usb: usbck {
 					compatible = "atmel,at91rm9200-clk-usb";
 					#clock-cells = <0>;
-					atmel,clk-divisors = <1 2>;
+					atmel,clk-divisors = <1 2 0 0>;
 					clocks = <&pllb>;
 				};
 

arch/arm/boot/dts/at91sam9g20.dtsi

@@ -40,6 +40,7 @@ plla: pllack {
 				};
 
 				pllb: pllbck {
+					compatible = "atmel,at91sam9g20-clk-pllb";
 					atmel,clk-input-range = <2000000 32000000>;
 					atmel,pll-clk-output-ranges = <30000000 100000000 0 0>;
 				};

arch/arm/boot/dts/dra7-evm.dts

@@ -8,6 +8,7 @@
 /dts-v1/;
 
 #include "dra74x.dtsi"
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "TI DRA742";
@@ -24,9 +25,29 @@ mmc2_3v3: fixedregulator-mmc2 {
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 	};
+
+	vtt_fixed: fixedregulator-vtt {
+		compatible = "regulator-fixed";
+		regulator-name = "vtt_fixed";
+		regulator-min-microvolt = <1350000>;
+		regulator-max-microvolt = <1350000>;
+		regulator-always-on;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&gpio7 11 GPIO_ACTIVE_HIGH>;
+	};
 };
 
 &dra7_pmx_core {
+	pinctrl-names = "default";
+	pinctrl-0 = <&vtt_pin>;
+
+	vtt_pin: pinmux_vtt_pin {
+		pinctrl-single,pins = <
+			0x3b4 (PIN_OUTPUT | MUX_MODE14) /* spi1_cs1.gpio7_11 */
+		>;
+	};
+
 	i2c1_pins: pinmux_i2c1_pins {
 		pinctrl-single,pins = <
 			0x400 (PIN_INPUT | MUX_MODE0) /* i2c1_sda */
@@ -43,20 +64,19 @@ i2c2_pins: pinmux_i2c2_pins {
 
 	i2c3_pins: pinmux_i2c3_pins {
 		pinctrl-single,pins = <
-			0x410 (PIN_INPUT | MUX_MODE0) /* i2c3_sda */
-			0x414 (PIN_INPUT | MUX_MODE0) /* i2c3_scl */
+			0x288 (PIN_INPUT | MUX_MODE9) /* gpio6_14.i2c3_sda */
+			0x28c (PIN_INPUT | MUX_MODE9) /* gpio6_15.i2c3_scl */
 		>;
 	};
 
 	mcspi1_pins: pinmux_mcspi1_pins {
 		pinctrl-single,pins = <
-			0x3a4 (PIN_INPUT | MUX_MODE0) /* spi2_clk */
-			0x3a8 (PIN_INPUT | MUX_MODE0) /* spi2_d1 */
-			0x3ac (PIN_INPUT | MUX_MODE0) /* spi2_d0 */
-			0x3b0 (PIN_INPUT_SLEW | MUX_MODE0) /* spi2_cs0 */
-			0x3b4 (PIN_INPUT_SLEW | MUX_MODE0) /* spi2_cs1 */
-			0x3b8 (PIN_INPUT_SLEW | MUX_MODE6) /* spi2_cs2 */
-			0x3bc (PIN_INPUT_SLEW | MUX_MODE6) /* spi2_cs3 */
+			0x3a4 (PIN_INPUT | MUX_MODE0) /* spi1_sclk */
+			0x3a8 (PIN_INPUT | MUX_MODE0) /* spi1_d1 */
+			0x3ac (PIN_INPUT | MUX_MODE0) /* spi1_d0 */
+			0x3b0 (PIN_INPUT_SLEW | MUX_MODE0) /* spi1_cs0 */
+			0x3b8 (PIN_INPUT_SLEW | MUX_MODE6) /* spi1_cs2.hdmi1_hpd */
+			0x3bc (PIN_INPUT_SLEW | MUX_MODE6) /* spi1_cs3.hdmi1_cec */
 		>;
 	};
 
@@ -284,7 +304,7 @@ &i2c3 {
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c3_pins>;
-	clock-frequency = <3400000>;
+	clock-frequency = <400000>;
 };
 
 &mcspi1 {
@@ -483,7 +503,7 @@ partition@6 {
 			reg = <0x001c0000 0x00020000>;
 		};
 		partition@7 {
-			label = "NAND.u-boot-env";
+			label = "NAND.u-boot-env.backup1";
 			reg = <0x001e0000 0x00020000>;
 		};
 		partition@8 {
@@ -504,3 +524,8 @@ &usb2_phy1 {
 &usb2_phy2 {
 	phy-supply = <&ldousb_reg>;
 };
+
+&gpio7 {
+	ti,no-reset-on-init;
+	ti,no-idle-on-init;
+};

arch/arm/boot/dts/omap3xxx-clocks.dtsi

@@ -467,6 +467,7 @@ dpll4_m5x2_ck: dpll4_m5x2_ck {
 		ti,bit-shift = <0x1e>;
 		reg = <0x0d00>;
 		ti,set-bit-to-disable;
+		ti,set-rate-parent;
 	};
 
 	dpll4_m6_ck: dpll4_m6_ck {

arch/arm/boot/dts/ste-snowball.dts

@@ -116,7 +116,6 @@ msp1: msp@80124000 {
 		msp2: msp@80117000 {
 			pinctrl-names = "default";
 			pinctrl-0 = <&msp2_default_mode>;
-			status = "okay";
 		};
 
 		msp3: msp@80125000 {

arch/arm/common/edma.c

@@ -1443,14 +1443,14 @@ void edma_assign_channel_eventq(unsigned channel, enum dma_event_q eventq_no)
 EXPORT_SYMBOL(edma_assign_channel_eventq);
 
 static int edma_setup_from_hw(struct device *dev, struct edma_soc_info *pdata,
-			      struct edma *edma_cc)
+			      struct edma *edma_cc, int cc_id)
 {
 	int i;
 	u32 value, cccfg;
 	s8 (*queue_priority_map)[2];
 
 	/* Decode the eDMA3 configuration from CCCFG register */
-	cccfg = edma_read(0, EDMA_CCCFG);
+	cccfg = edma_read(cc_id, EDMA_CCCFG);
 
 	value = GET_NUM_REGN(cccfg);
 	edma_cc->num_region = BIT(value);
@@ -1464,7 +1464,8 @@ static int edma_setup_from_hw(struct device *dev, struct edma_soc_info *pdata,
 	value = GET_NUM_EVQUE(cccfg);
 	edma_cc->num_tc = value + 1;
 
-	dev_dbg(dev, "eDMA3 HW configuration (cccfg: 0x%08x):\n", cccfg);
+	dev_dbg(dev, "eDMA3 CC%d HW configuration (cccfg: 0x%08x):\n", cc_id,
+		cccfg);
 	dev_dbg(dev, "num_region: %u\n", edma_cc->num_region);
 	dev_dbg(dev, "num_channel: %u\n", edma_cc->num_channels);
 	dev_dbg(dev, "num_slot: %u\n", edma_cc->num_slots);
@@ -1684,7 +1685,7 @@ static int edma_probe(struct platform_device *pdev)
 			return -ENOMEM;
 
 		/* Get eDMA3 configuration from IP */
-		ret = edma_setup_from_hw(dev, info[j], edma_cc[j]);
+		ret = edma_setup_from_hw(dev, info[j], edma_cc[j], j);
 		if (ret)
 			return ret;
 

arch/arm/mach-at91/board-dt-rm9200.c

@@ -14,6 +14,7 @@
 #include <linux/gpio.h>
 #include <linux/of.h>
 #include <linux/of_irq.h>
+#include <linux/clk-provider.h>
 
 #include <asm/setup.h>
 #include <asm/irq.h>
@@ -35,13 +36,21 @@ static void __init at91rm9200_dt_init_irq(void)
 	of_irq_init(irq_of_match);
 }
 
+static void __init at91rm9200_dt_timer_init(void)
+{
+#if defined(CONFIG_COMMON_CLK)
+	of_clk_init(NULL);
+#endif
+	at91rm9200_timer_init();
+}
+
 static const char *at91rm9200_dt_board_compat[] __initdata = {
 	"atmel,at91rm9200",
 	NULL
 };
 
 DT_MACHINE_START(at91rm9200_dt, "Atmel AT91RM9200 (Device Tree)")
-	.init_time      = at91rm9200_timer_init,
+	.init_time      = at91rm9200_dt_timer_init,
 	.map_io		= at91_map_io,
 	.handle_irq	= at91_aic_handle_irq,
 	.init_early	= at91rm9200_dt_initialize,

arch/arm/mach-omap2/gpmc.c

@@ -1207,8 +1207,7 @@ int gpmc_cs_program_settings(int cs, struct gpmc_settings *p)
 		}
 	}
 
-	if ((p->wait_on_read || p->wait_on_write) &&
-	    (p->wait_pin > gpmc_nr_waitpins)) {
+	if (p->wait_pin > gpmc_nr_waitpins) {
 		pr_err("%s: invalid wait-pin (%d)\n", __func__, p->wait_pin);
 		return -EINVAL;
 	}
@@ -1288,8 +1287,8 @@ void gpmc_read_settings_dt(struct device_node *np, struct gpmc_settings *p)
 		p->wait_on_write = of_property_read_bool(np,
 							 "gpmc,wait-on-write");
 		if (!p->wait_on_read && !p->wait_on_write)
-			pr_warn("%s: read/write wait monitoring not enabled!\n",
-				__func__);
+			pr_debug("%s: rd/wr wait monitoring not enabled!\n",
+				 __func__);
 	}
 }
 

drivers/bus/arm-ccn.c

@@ -586,6 +586,30 @@ static int arm_ccn_pmu_type_eq(u32 a, u32 b)
 	return 0;
 }
 
+static void arm_ccn_pmu_event_destroy(struct perf_event *event)
+{
+	struct arm_ccn *ccn = pmu_to_arm_ccn(event->pmu);
+	struct hw_perf_event *hw = &event->hw;
+
+	if (hw->idx == CCN_IDX_PMU_CYCLE_COUNTER) {
+		clear_bit(CCN_IDX_PMU_CYCLE_COUNTER, ccn->dt.pmu_counters_mask);
+	} else {
+		struct arm_ccn_component *source =
+				ccn->dt.pmu_counters[hw->idx].source;
+
+		if (CCN_CONFIG_TYPE(event->attr.config) == CCN_TYPE_XP &&
+				CCN_CONFIG_EVENT(event->attr.config) ==
+				CCN_EVENT_WATCHPOINT)
+			clear_bit(hw->config_base, source->xp.dt_cmp_mask);
+		else
+			clear_bit(hw->config_base, source->pmu_events_mask);
+		clear_bit(hw->idx, ccn->dt.pmu_counters_mask);
+	}
+
+	ccn->dt.pmu_counters[hw->idx].source = NULL;
+	ccn->dt.pmu_counters[hw->idx].event = NULL;
+}
+
 static int arm_ccn_pmu_event_init(struct perf_event *event)
 {
 	struct arm_ccn *ccn;
@@ -599,6 +623,7 @@ static int arm_ccn_pmu_event_init(struct perf_event *event)
 		return -ENOENT;
 
 	ccn = pmu_to_arm_ccn(event->pmu);
+	event->destroy = arm_ccn_pmu_event_destroy;
 
 	if (hw->sample_period) {
 		dev_warn(ccn->dev, "Sampling not supported!\n");
@@ -731,30 +756,6 @@ static int arm_ccn_pmu_event_init(struct perf_event *event)
 	return 0;
 }
 
-static void arm_ccn_pmu_event_free(struct perf_event *event)
-{
-	struct arm_ccn *ccn = pmu_to_arm_ccn(event->pmu);
-	struct hw_perf_event *hw = &event->hw;
-
-	if (hw->idx == CCN_IDX_PMU_CYCLE_COUNTER) {
-		clear_bit(CCN_IDX_PMU_CYCLE_COUNTER, ccn->dt.pmu_counters_mask);
-	} else {
-		struct arm_ccn_component *source =
-				ccn->dt.pmu_counters[hw->idx].source;
-
-		if (CCN_CONFIG_TYPE(event->attr.config) == CCN_TYPE_XP &&
-				CCN_CONFIG_EVENT(event->attr.config) ==
-				CCN_EVENT_WATCHPOINT)
-			clear_bit(hw->config_base, source->xp.dt_cmp_mask);
-		else
-			clear_bit(hw->config_base, source->pmu_events_mask);
-		clear_bit(hw->idx, ccn->dt.pmu_counters_mask);
-	}
-
-	ccn->dt.pmu_counters[hw->idx].source = NULL;
-	ccn->dt.pmu_counters[hw->idx].event = NULL;
-}
-
 static u64 arm_ccn_pmu_read_counter(struct arm_ccn *ccn, int idx)
 {
 	u64 res;
@@ -1027,8 +1028,6 @@ static int arm_ccn_pmu_event_add(struct perf_event *event, int flags)
 static void arm_ccn_pmu_event_del(struct perf_event *event, int flags)
 {
 	arm_ccn_pmu_event_stop(event, PERF_EF_UPDATE);
-
-	arm_ccn_pmu_event_free(event);
 }
 
 static void arm_ccn_pmu_event_read(struct perf_event *event)