ARM: dts: dra7x-evm: switch to new cpsw switch drv

Switch all TI DRA7x boards to use new cpsw switch driver. Those boards
configured in dual_mac mode by default. Hence, dual_mac mode has been
preserved the same way between legacy and new driver it's safe to switch
drivers.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

arch/arm/boot/dts/dra7-evm.dts

@@ -537,24 +537,23 @@ &gpio7_target {
 	ti,no-idle-on-init;
 };
 
-&mac {
+&mac_sw {
 	status = "okay";
-	dual_emac;
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-handle = <&ethphy0>;
 	phy-mode = "rgmii";
-	dual_emac_res_vlan = <1>;
+	ti,dual-emac-pvid = <1>;
 };
 
-&cpsw_emac1 {
+&cpsw_port2 {
 	phy-handle = <&ethphy1>;
 	phy-mode = "rgmii";
-	dual_emac_res_vlan = <2>;
+	ti,dual-emac-pvid = <2>;
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	ethphy0: ethernet-phy@2 {
 		reg = <2>;
 	};

arch/arm/boot/dts/dra71-evm.dts

@@ -219,26 +219,26 @@ &mmc2 {
 	vqmmc-supply = <&evm_1v8_sw>;
 };
 
-&mac {
+&mac_sw {
 	mode-gpios = <&pcf_gpio_21 4 GPIO_ACTIVE_LOW>,
 		     <&pcf_hdmi 9 GPIO_ACTIVE_LOW>,	/* P11 */
 		     <&pcf_hdmi 10 GPIO_ACTIVE_LOW>;	/* P12 */
-	dual_emac;
+	status = "okay";
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-handle = <&dp83867_0>;
 	phy-mode = "rgmii-id";
-	dual_emac_res_vlan = <1>;
+	ti,dual-emac-pvid = <1>;
 };
 
-&cpsw_emac1 {
+&cpsw_port2 {
 	phy-handle = <&dp83867_1>;
 	phy-mode = "rgmii-id";
-	dual_emac_res_vlan = <2>;
+	ti,dual-emac-pvid = <2>;
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	dp83867_0: ethernet-phy@2 {
 		reg = <2>;
 		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;

arch/arm/boot/dts/dra72-evm-common.dtsi

@@ -462,10 +462,6 @@ wifi@2 {
 	};
 };
 
-&mac {
-	status = "okay";
-};
-
 &dcan1 {
 	status = "okay";
 	pinctrl-names = "default", "sleep", "active";

arch/arm/boot/dts/dra72-evm-revc.dts

@@ -77,26 +77,26 @@ &pcf_gpio_21 {
 	interrupts = <30 IRQ_TYPE_EDGE_FALLING>;
 };
 
-&mac {
+&mac_sw {
 	mode-gpios = <&pcf_gpio_21 4 GPIO_ACTIVE_LOW>,
 		     <&pcf_hdmi 9 GPIO_ACTIVE_LOW>,	/* P11 */
 		     <&pcf_hdmi 10 GPIO_ACTIVE_LOW>;	/* P12 */
-	dual_emac;
+	status = "okay";
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-handle = <&dp83867_0>;
 	phy-mode = "rgmii-id";
-	dual_emac_res_vlan = <1>;
+	ti,dual-emac-pvid = <1>;
 };
 
-&cpsw_emac1 {
+&cpsw_port2 {
 	phy-handle = <&dp83867_1>;
 	phy-mode = "rgmii-id";
-	dual_emac_res_vlan = <2>;
+	ti,dual-emac-pvid = <2>;
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	dp83867_0: ethernet-phy@2 {
 		reg = <2>;
 		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;

arch/arm/boot/dts/dra72-evm.dts

@@ -69,17 +69,22 @@ &pcf_gpio_21 {
 	interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
 };
 
-&mac {
-	slaves = <1>;
+&mac_sw {
 	mode-gpios = <&pcf_gpio_21 4 GPIO_ACTIVE_HIGH>;
+	status = "okay";
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-handle = <&ethphy0>;
 	phy-mode = "rgmii";
+	ti,dual-emac-pvid = <1>;
+};
+
+&cpsw_port2 {
+	status = "disabled";
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	ethphy0: ethernet-phy@3 {
 		reg = <3>;
 	};

arch/arm/boot/dts/dra76-evm.dts

@@ -475,25 +475,23 @@ &rtc {
 	status = "disabled";
 };
 
-&mac {
+&mac_sw {
 	status = "okay";
-
-	dual_emac;
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-handle = <&dp83867_0>;
 	phy-mode = "rgmii-id";
-	dual_emac_res_vlan = <1>;
+	ti,dual-emac-pvid = <1>;
 };
 
-&cpsw_emac1 {
+&cpsw_port2 {
 	phy-handle = <&dp83867_1>;
 	phy-mode = "rgmii-id";
-	dual_emac_res_vlan = <2>;
+	ti,dual-emac-pvid = <2>;
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	dp83867_0: ethernet-phy@2 {
 		reg = <2>;
 		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;