Commit 56d79422 authored by Ludovic Desroches's avatar Ludovic Desroches Committed by Linus Walleij

pinctrl: dt-binding: Add DT binding documentation for Atmel PIO4

Add documentation for the Atmel PIO4 controller introduced with SAMA5D2
chip family.
Signed-off-by: default avatarLudovic Desroches <ludovic.desroches@atmel.com>
Acked-by: default avatarSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: default avatarLinus Walleij <linus.walleij@linaro.org>
parent 77618084
* Atmel PIO4 Controller
The Atmel PIO4 controller is used to select the function of a pin and to
configure it.
Required properties:
- compatible: "atmel,sama5d2-pinctrl".
- reg: base address and length of the PIO controller.
- interrupts: interrupt outputs from the controller, one for each bank.
- interrupt-controller: mark the device node as an interrupt controller.
- #interrupt-cells: should be two.
- gpio-controller: mark the device node as a gpio controller.
- #gpio-cells: should be two.
Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
a general description of GPIO and interrupt bindings.
Please refer to pinctrl-bindings.txt in this directory for details of the
common pinctrl bindings used by client devices.
Subnode format
Each node (or subnode) will list the pins it needs and how to configured these
pins.
node {
pinmux = <PIN_NUMBER_PINMUX>;
GENERIC_PINCONFIG;
};
Required properties:
- pinmux: integer array. Each integer represents a pin number plus mux and
ioset settings. Use the macros from boot/dts/<soc>-pinfunc.h file to get the
right representation of the pin.
Optional properties:
- GENERIC_PINCONFIG: generic pinconfig options to use, bias-disable,
bias-pull-down, bias-pull-up, drive-open-drain, input-schmitt-enable,
input-debounce, output-low, output-high.
Example:
#include <sama5d2-pinfunc.h>
...
{
pioA: pinctrl@fc038000 {
compatible = "atmel,sama5d2-pinctrl";
reg = <0xfc038000 0x600>;
interrupts = <18 IRQ_TYPE_LEVEL_HIGH 7>,
<68 IRQ_TYPE_LEVEL_HIGH 7>,
<69 IRQ_TYPE_LEVEL_HIGH 7>,
<70 IRQ_TYPE_LEVEL_HIGH 7>;
interrupt-controller;
#interrupt-cells = <2>;
gpio-controller;
#gpio-cells = <2>;
clocks = <&pioA_clk>;
pinctrl_i2c0_default: i2c0_default {
pinmux = <PIN_PD21__TWD0>,
<PIN_PD22__TWCK0>;
bias-disable;
};
pinctrl_led_gpio_default: led_gpio_default {
pinmux = <PIN_PB0>,
<PIN_PB5>;
bias-pull-up;
};
pinctrl_sdmmc1_default: sdmmc1_default {
cmd_data {
pinmux = <PIN_PA28__SDMMC1_CMD>,
<PIN_PA18__SDMMC1_DAT0>,
<PIN_PA19__SDMMC1_DAT1>,
<PIN_PA20__SDMMC1_DAT2>,
<PIN_PA21__SDMMC1_DAT3>;
bias-pull-up;
};
ck_cd {
pinmux = <PIN_PA22__SDMMC1_CK>,
<PIN_PA30__SDMMC1_CD>;
bias-disable;
};
};
...
};
};
...
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment