Commit 5766d204 authored by Jarod Wilson's avatar Jarod Wilson Committed by Mauro Carvalho Chehab

[media] lirc_zilog: z8 on usb doesn't like back-to-back i2c_master_send

Both the HD-PVR and HVR-1950, driven by the hdpvr and pvrusb2 drivers
respectively, have a zilog z8 chip exposed via i2c. These are both
usb-connected devices, and on both of them, back-to-back i2c_master_send
calls that work fine with a z8 on a pci card fail with a -EIO, as the
chip isn't yet ready from the prior command. To cope with that, add a
delay and retry loop where necessary.
Acked-by: default avatarAndy Walls <awalls@md.metrocast.net>
Signed-off-by: default avatarJarod Wilson <jarod@redhat.com>
Signed-off-by: default avatarMauro Carvalho Chehab <mchehab@redhat.com>
parent 7f2a06de
......@@ -495,7 +495,7 @@ static int send_data_block(struct IR_tx *tx, unsigned char *data_block)
/* send boot data to the IR TX device */
static int send_boot_data(struct IR_tx *tx)
{
int ret;
int ret, i;
unsigned char buf[4];
/* send the boot block */
......@@ -503,7 +503,7 @@ static int send_boot_data(struct IR_tx *tx)
if (ret != 0)
return ret;
/* kick it off? */
/* Hit the go button to activate the new boot data */
buf[0] = 0x00;
buf[1] = 0x20;
ret = i2c_master_send(tx->c, buf, 2);
......@@ -511,7 +511,19 @@ static int send_boot_data(struct IR_tx *tx)
zilog_error("i2c_master_send failed with %d\n", ret);
return ret < 0 ? ret : -EFAULT;
}
ret = i2c_master_send(tx->c, buf, 1);
/*
* Wait for zilog to settle after hitting go post boot block upload.
* Without this delay, the HD-PVR and HVR-1950 both return an -EIO
* upon attempting to get firmware revision, and tx probe thus fails.
*/
for (i = 0; i < 10; i++) {
ret = i2c_master_send(tx->c, buf, 1);
if (ret == 1)
break;
udelay(100);
}
if (ret != 1) {
zilog_error("i2c_master_send failed with %d\n", ret);
return ret < 0 ? ret : -EFAULT;
......@@ -523,8 +535,8 @@ static int send_boot_data(struct IR_tx *tx)
zilog_error("i2c_master_recv failed with %d\n", ret);
return 0;
}
if (buf[0] != 0x80) {
zilog_error("unexpected IR TX response: %02x\n", buf[0]);
if ((buf[0] != 0x80) && (buf[0] != 0xa0)) {
zilog_error("unexpected IR TX init response: %02x\n", buf[0]);
return 0;
}
zilog_notify("Zilog/Hauppauge IR blaster firmware version "
......@@ -827,7 +839,15 @@ static int send_code(struct IR_tx *tx, unsigned int code, unsigned int key)
zilog_error("i2c_master_send failed with %d\n", ret);
return ret < 0 ? ret : -EFAULT;
}
ret = i2c_master_send(tx->c, buf, 1);
/* Give the z8 a moment to process data block */
for (i = 0; i < 10; i++) {
ret = i2c_master_send(tx->c, buf, 1);
if (ret == 1)
break;
udelay(100);
}
if (ret != 1) {
zilog_error("i2c_master_send failed with %d\n", ret);
return ret < 0 ? ret : -EFAULT;
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment