Commit 57bb7e22 authored by Anton Vorontsov's avatar Anton Vorontsov Committed by Jeff Garzik

phy/broadcom: add support for BCM5481 PHY

This patch adds support for BCM5481 PHY. Unfortunately it's hard to
get specifications for this PHY, so its special register 0x18 isn't
annotated properly (but we know it's used to set up the delays).

I've kept the magic numbers, so we'll not forget to fix it at the
first opportunity, and will name that register and its bits correctly.

p.s. also fixed the line with broken indention, introduced by
commit 03157ac3
    PHYLIB: Add BCM5482 PHY support
Signed-off-by: default avatarAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: default avatarJeff Garzik <jeff@garzik.org>
parent b39b5a2b
......@@ -99,6 +99,41 @@ static int bcm54xx_config_intr(struct phy_device *phydev)
return err;
}
static int bcm5481_config_aneg(struct phy_device *phydev)
{
int ret;
/* Aneg firsly. */
ret = genphy_config_aneg(phydev);
/* Then we can set up the delay. */
if (phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID) {
u16 reg;
/*
* There is no BCM5481 specification available, so down
* here is everything we know about "register 0x18". This
* at least helps BCM5481 to successfuly receive packets
* on MPC8360E-RDK board. Peter Barada <peterb@logicpd.com>
* says: "This sets delay between the RXD and RXC signals
* instead of using trace lengths to achieve timing".
*/
/* Set RDX clk delay. */
reg = 0x7 | (0x7 << 12);
phy_write(phydev, 0x18, reg);
reg = phy_read(phydev, 0x18);
/* Set RDX-RXC skew. */
reg |= (1 << 8);
/* Write bits 14:0. */
reg |= (1 << 15);
phy_write(phydev, 0x18, reg);
}
return ret;
}
static struct phy_driver bcm5411_driver = {
.phy_id = 0x00206070,
.phy_id_mask = 0xfffffff0,
......@@ -141,8 +176,22 @@ static struct phy_driver bcm5461_driver = {
.driver = { .owner = THIS_MODULE },
};
static struct phy_driver bcm5481_driver = {
.phy_id = 0x0143bca0,
.phy_id_mask = 0xfffffff0,
.name = "Broadcom BCM5481",
.features = PHY_GBIT_FEATURES,
.flags = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
.config_init = bcm54xx_config_init,
.config_aneg = bcm5481_config_aneg,
.read_status = genphy_read_status,
.ack_interrupt = bcm54xx_ack_interrupt,
.config_intr = bcm54xx_config_intr,
.driver = { .owner = THIS_MODULE },
};
static struct phy_driver bcm5482_driver = {
.phy_id = 0x0143bcb0,
.phy_id = 0x0143bcb0,
.phy_id_mask = 0xfffffff0,
.name = "Broadcom BCM5482",
.features = PHY_GBIT_FEATURES,
......@@ -168,12 +217,17 @@ static int __init broadcom_init(void)
ret = phy_driver_register(&bcm5461_driver);
if (ret)
goto out_5461;
ret = phy_driver_register(&bcm5481_driver);
if (ret)
goto out_5481;
ret = phy_driver_register(&bcm5482_driver);
if (ret)
goto out_5482;
return ret;
out_5482:
phy_driver_unregister(&bcm5481_driver);
out_5481:
phy_driver_unregister(&bcm5461_driver);
out_5461:
phy_driver_unregister(&bcm5421_driver);
......@@ -186,6 +240,7 @@ static int __init broadcom_init(void)
static void __exit broadcom_exit(void)
{
phy_driver_unregister(&bcm5482_driver);
phy_driver_unregister(&bcm5481_driver);
phy_driver_unregister(&bcm5461_driver);
phy_driver_unregister(&bcm5421_driver);
phy_driver_unregister(&bcm5411_driver);
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment