Merge branch 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6

* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (74 commits)
  PCI: make msi_free_irqs() to use msix_mask_irq() instead of open coded write
  PCI: Fix the NIU MSI-X problem in a better way
  PCI ASPM: remove get_root_port_link
  PCI ASPM: cleanup pcie_aspm_sanity_check
  PCI ASPM: remove has_switch field
  PCI ASPM: cleanup calc_Lx_latency
  PCI ASPM: cleanup pcie_aspm_get_cap_device
  PCI ASPM: cleanup clkpm checks
  PCI ASPM: cleanup __pcie_aspm_check_state_one
  PCI ASPM: cleanup initialization
  PCI ASPM: cleanup change input argument of aspm functions
  PCI ASPM: cleanup misc in struct pcie_link_state
  PCI ASPM: cleanup clkpm state in struct pcie_link_state
  PCI ASPM: cleanup latency field in struct pcie_link_state
  PCI ASPM: cleanup aspm state field in struct pcie_link_state
  PCI ASPM: fix typo in struct pcie_link_state
  PCI: drivers/pci/slot.c should depend on CONFIG_SYSFS
  PCI: remove redundant __msi_set_enable()
  PCI PM: consistently use type bool for wake enable variable
  x86/ACPI: Correct maximum allowed _CRS returned resources and warn if exceeded
  ...

Documentation/ABI/testing/sysfs-bus-pci

@@ -122,3 +122,10 @@ Description:
 		This symbolic link appears when a device is a Virtual Function.
 		The symbolic link points to the PCI device sysfs entry of the
 		Physical Function this device associates with.
+
+What:		/sys/bus/pci/slots/.../module
+Date:		June 2009
+Contact:	linux-pci@vger.kernel.org
+Description:
+		This symbolic link points to the PCI hotplug controller driver
+		module that manages the hotplug slot.

Documentation/PCI/pcieaer-howto.txt

@@ -61,6 +61,10 @@ be initiated although firmwares have no _OSC support. To enable the
 walkaround, pls. add aerdriver.forceload=y to kernel boot parameter line
 when booting kernel. Note that forceload=n by default.
 
+nosourceid, another parameter of type bool, can be used when broken
+hardware (mostly chipsets) has root ports that cannot obtain the reporting
+source ID. nosourceid=n by default.
+
 2.3 AER error output
 When a PCI-E AER error is captured, an error message will be outputed to
 console. If it's a correctable error, it is outputed as a warning.
@@ -246,3 +250,24 @@ with the PCI Express AER Root driver?
 A: It could call the helper functions to enable AER in devices and
 cleanup uncorrectable status register. Pls. refer to section 3.3.
 
+
+4. Software error injection
+
+Debugging PCIE AER error recovery code is quite difficult because it
+is hard to trigger real hardware errors. Software based error
+injection can be used to fake various kinds of PCIE errors.
+
+First you should enable PCIE AER software error injection in kernel
+configuration, that is, following item should be in your .config.
+
+CONFIG_PCIEAER_INJECT=y or CONFIG_PCIEAER_INJECT=m
+
+After reboot with new kernel or insert the module, a device file named
+/dev/aer_inject should be created.
+
+Then, you need a user space tool named aer-inject, which can be gotten
+from:
+    http://www.kernel.org/pub/linux/utils/pci/aer-inject/
+
+More information about aer-inject can be found in the document comes
+with its source code.

Documentation/kernel-parameters.txt

@@ -1776,6 +1776,9 @@ and is between 256 and 4096 characters. It is defined in the file
 				root domains (aka PCI segments, in ACPI-speak).
 		nommconf	[X86] Disable use of MMCONFIG for PCI
 				Configuration
+		check_enable_amd_mmconf [X86] check for and enable
+				properly configured MMIO access to PCI
+				config space on AMD family 10h CPU
 		nomsi		[MSI] If the PCI_MSI kernel config parameter is
 				enabled, this kernel boot option can be used to
 				disable the use of MSI interrupts system-wide.
@@ -1828,7 +1831,7 @@ and is between 256 and 4096 characters. It is defined in the file
 				IRQ routing is enabled.
 		noacpi		[X86] Do not use ACPI for IRQ routing
 				or for PCI scanning.
-		use_crs		[X86] Use _CRS for PCI resource
+		nocrs		[X86] Don't use _CRS for PCI resource
 				allocation.
 		routeirq	Do IRQ routing for all PCI devices.
 				This is normally done in pci_enable_device(),
@@ -1865,6 +1868,12 @@ and is between 256 and 4096 characters. It is defined in the file
 				PAGE_SIZE is used as alignment.
 				PCI-PCI bridge can be specified, if resource
 				windows need to be expanded.
+		ecrc=		Enable/disable PCIe ECRC (transaction layer
+				end-to-end CRC checking).
+				bios: Use BIOS/firmware settings. This is the
+				the default.
+				off: Turn ECRC off
+				on: Turn ECRC on.
 
 	pcie_aspm=	[PCIE] Forcibly enable or disable PCIe Active State Power
 			Management.

arch/powerpc/platforms/pseries/eeh_driver.c

@@ -122,7 +122,7 @@ static void eeh_enable_irq(struct pci_dev *dev)
  * passed back in "userdata".
  */
 
-static void eeh_report_error(struct pci_dev *dev, void *userdata)
+static int eeh_report_error(struct pci_dev *dev, void *userdata)
 {
 	enum pci_ers_result rc, *res = userdata;
 	struct pci_driver *driver = dev->driver;
@@ -130,19 +130,21 @@ static void eeh_report_error(struct pci_dev *dev, void *userdata)
 	dev->error_state = pci_channel_io_frozen;
 
 	if (!driver)
-		return;
+		return 0;
 
 	eeh_disable_irq(dev);
 
 	if (!driver->err_handler ||
 	    !driver->err_handler->error_detected)
-		return;
+		return 0;
 
 	rc = driver->err_handler->error_detected (dev, pci_channel_io_frozen);
 
 	/* A driver that needs a reset trumps all others */
 	if (rc == PCI_ERS_RESULT_NEED_RESET) *res = rc;
 	if (*res == PCI_ERS_RESULT_NONE) *res = rc;
+
+	return 0;
 }
 
 /**
@@ -153,7 +155,7 @@ static void eeh_report_error(struct pci_dev *dev, void *userdata)
  * Cumulative response passed back in "userdata".
  */
 
-static void eeh_report_mmio_enabled(struct pci_dev *dev, void *userdata)
+static int eeh_report_mmio_enabled(struct pci_dev *dev, void *userdata)
 {
 	enum pci_ers_result rc, *res = userdata;
 	struct pci_driver *driver = dev->driver;
@@ -161,26 +163,28 @@ static void eeh_report_mmio_enabled(struct pci_dev *dev, void *userdata)
 	if (!driver ||
 	    !driver->err_handler ||
 	    !driver->err_handler->mmio_enabled)
-		return;
+		return 0;
 
 	rc = driver->err_handler->mmio_enabled (dev);
 
 	/* A driver that needs a reset trumps all others */
 	if (rc == PCI_ERS_RESULT_NEED_RESET) *res = rc;
 	if (*res == PCI_ERS_RESULT_NONE) *res = rc;
+
+	return 0;
 }
 
 /**
  * eeh_report_reset - tell device that slot has been reset
  */
 
-static void eeh_report_reset(struct pci_dev *dev, void *userdata)
+static int eeh_report_reset(struct pci_dev *dev, void *userdata)
 {
 	enum pci_ers_result rc, *res = userdata;
 	struct pci_driver *driver = dev->driver;
 
 	if (!driver)
-		return;
+		return 0;
 
 	dev->error_state = pci_channel_io_normal;
 
@@ -188,35 +192,39 @@ static void eeh_report_reset(struct pci_dev *dev, void *userdata)
 
 	if (!driver->err_handler ||
 	    !driver->err_handler->slot_reset)
-		return;
+		return 0;
 
 	rc = driver->err_handler->slot_reset(dev);
 	if ((*res == PCI_ERS_RESULT_NONE) ||
 	    (*res == PCI_ERS_RESULT_RECOVERED)) *res = rc;
 	if (*res == PCI_ERS_RESULT_DISCONNECT &&
 	     rc == PCI_ERS_RESULT_NEED_RESET) *res = rc;
+
+	return 0;
 }
 
 /**
  * eeh_report_resume - tell device to resume normal operations
  */
 
-static void eeh_report_resume(struct pci_dev *dev, void *userdata)
+static int eeh_report_resume(struct pci_dev *dev, void *userdata)
 {
 	struct pci_driver *driver = dev->driver;
 
 	dev->error_state = pci_channel_io_normal;
 
 	if (!driver)
-		return;
+		return 0;
 
 	eeh_enable_irq(dev);
 
 	if (!driver->err_handler ||
 	    !driver->err_handler->resume)
-		return;
+		return 0;
 
 	driver->err_handler->resume(dev);
+
+	return 0;
 }
 
 /**
@@ -226,22 +234,24 @@ static void eeh_report_resume(struct pci_dev *dev, void *userdata)
  * dead, and that no further recovery attempts will be made on it.
  */
 
-static void eeh_report_failure(struct pci_dev *dev, void *userdata)
+static int eeh_report_failure(struct pci_dev *dev, void *userdata)
 {
 	struct pci_driver *driver = dev->driver;
 
 	dev->error_state = pci_channel_io_perm_failure;
 
 	if (!driver)
-		return;
+		return 0;
 
 	eeh_disable_irq(dev);
 
 	if (!driver->err_handler ||
 	    !driver->err_handler->error_detected)
-		return;
+		return 0;
 
 	driver->err_handler->error_detected(dev, pci_channel_io_perm_failure);
+
+	return 0;
 }
 
 /* ------------------------------------------------------- */

arch/x86/include/asm/pci.h

@@ -130,6 +130,7 @@ extern void pci_iommu_alloc(void);
 
 /* generic pci stuff */
 #include <asm-generic/pci.h>
+#define PCIBIOS_MAX_MEM_32 0xffffffff
 
 #ifdef CONFIG_NUMA
 /* Returns the node based on pci bus */

arch/x86/include/asm/pci_x86.h

@@ -25,7 +25,7 @@
 #define PCI_BIOS_IRQ_SCAN	0x2000
 #define PCI_ASSIGN_ALL_BUSSES	0x4000
 #define PCI_CAN_SKIP_ISA_ALIGN	0x8000
-#define PCI_USE__CRS		0x10000
+#define PCI_NO_ROOT_CRS		0x10000
 #define PCI_CHECK_ENABLE_AMD_MMCONF	0x20000
 #define PCI_HAS_IO_ECS		0x40000
 #define PCI_NOASSIGN_ROMS	0x80000

arch/x86/pci/acpi.c

@@ -38,15 +38,26 @@ count_resource(struct acpi_resource *acpi_res, void *data)
 	struct acpi_resource_address64 addr;
 	acpi_status status;
 
-	if (info->res_num >= PCI_BUS_NUM_RESOURCES)
-		return AE_OK;
-
 	status = resource_to_addr(acpi_res, &addr);
 	if (ACPI_SUCCESS(status))
 		info->res_num++;
 	return AE_OK;
 }
 
+static int
+bus_has_transparent_bridge(struct pci_bus *bus)
+{
+	struct pci_dev *dev;
+
+	list_for_each_entry(dev, &bus->devices, bus_list) {
+		u16 class = dev->class >> 8;
+
+		if (class == PCI_CLASS_BRIDGE_PCI && dev->transparent)
+			return true;
+	}
+	return false;
+}
+
 static acpi_status
 setup_resource(struct acpi_resource *acpi_res, void *data)
 {
@@ -56,9 +67,7 @@ setup_resource(struct acpi_resource *acpi_res, void *data)
 	acpi_status status;
 	unsigned long flags;
 	struct resource *root;
-
-	if (info->res_num >= PCI_BUS_NUM_RESOURCES)
-		return AE_OK;
+	int max_root_bus_resources = PCI_BUS_NUM_RESOURCES;
 
 	status = resource_to_addr(acpi_res, &addr);
 	if (!ACPI_SUCCESS(status))
@@ -82,6 +91,18 @@ setup_resource(struct acpi_resource *acpi_res, void *data)
 	res->end = res->start + addr.address_length - 1;
 	res->child = NULL;
 
+	if (bus_has_transparent_bridge(info->bus))
+		max_root_bus_resources -= 3;
+	if (info->res_num >= max_root_bus_resources) {
+		printk(KERN_WARNING "PCI: Failed to allocate 0x%lx-0x%lx "
+			"from %s for %s due to _CRS returning more than "
+			"%d resource descriptors\n", (unsigned long) res->start,
+			(unsigned long) res->end, root->name, info->name,
+			max_root_bus_resources);
+		info->res_num++;
+		return AE_OK;
+	}
+
 	if (insert_resource(root, res)) {
 		printk(KERN_ERR "PCI: Failed to allocate 0x%lx-0x%lx "
 			"from %s for %s\n", (unsigned long) res->start,
@@ -217,7 +238,7 @@ struct pci_bus * __devinit pci_acpi_scan_root(struct acpi_device *device, int do
 #endif
 	}
 
-	if (bus && (pci_probe & PCI_USE__CRS))
+	if (bus && !(pci_probe & PCI_NO_ROOT_CRS))
 		get_current_resources(device, busnum, domain, bus);
 	return bus;
 }

arch/x86/pci/amd_bus.c

@@ -101,7 +101,7 @@ void x86_pci_root_bus_res_quirks(struct pci_bus *b)
 	struct pci_root_info *info;
 
 	/* don't go for it if _CRS is used */
-	if (pci_probe & PCI_USE__CRS)
+	if (!(pci_probe & PCI_NO_ROOT_CRS))
 		return;
 
 	/* if only one root bus, don't need to anything */

arch/x86/pci/common.c

@@ -515,8 +515,8 @@ char * __devinit  pcibios_setup(char *str)
 	} else if (!strcmp(str, "assign-busses")) {
 		pci_probe |= PCI_ASSIGN_ALL_BUSSES;
 		return NULL;
-	} else if (!strcmp(str, "use_crs")) {
-		pci_probe |= PCI_USE__CRS;
+	} else if (!strcmp(str, "nocrs")) {
+		pci_probe |= PCI_NO_ROOT_CRS;
 		return NULL;
 	} else if (!strcmp(str, "earlydump")) {
 		pci_early_dump_regs = 1;

drivers/acpi/Kconfig

@@ -266,6 +266,7 @@ config ACPI_DEBUG_FUNC_TRACE
 
 config ACPI_PCI_SLOT
 	tristate "PCI slot detection driver"
+	depends on SYSFS
 	default n
 	help
 	  This driver creates entries in /sys/bus/pci/slots/ for all PCI

drivers/pci/Makefile

@@ -2,10 +2,11 @@
 # Makefile for the PCI bus specific drivers.
 #
 
-obj-y		+= access.o bus.o probe.o remove.o pci.o quirks.o slot.o \
+obj-y		+= access.o bus.o probe.o remove.o pci.o quirks.o \
 			pci-driver.o search.o pci-sysfs.o rom.o setup-res.o \
 			irq.o
 obj-$(CONFIG_PROC_FS) += proc.o
+obj-$(CONFIG_SYSFS) += slot.o
 
 # Build PCI Express stuff if needed
 obj-$(CONFIG_PCIEPORTBUS) += pcie/

drivers/pci/access.c

@@ -66,6 +66,25 @@ EXPORT_SYMBOL(pci_bus_write_config_byte);
 EXPORT_SYMBOL(pci_bus_write_config_word);
 EXPORT_SYMBOL(pci_bus_write_config_dword);
 
+/**
+ * pci_bus_set_ops - Set raw operations of pci bus
+ * @bus:	pci bus struct
+ * @ops:	new raw operations
+ *
+ * Return previous raw operations
+ */
+struct pci_ops *pci_bus_set_ops(struct pci_bus *bus, struct pci_ops *ops)
+{
+	struct pci_ops *old_ops;
+	unsigned long flags;
+
+	spin_lock_irqsave(&pci_lock, flags);
+	old_ops = bus->ops;
+	bus->ops = ops;
+	spin_unlock_irqrestore(&pci_lock, flags);
+	return old_ops;
+}
+EXPORT_SYMBOL(pci_bus_set_ops);
 
 /**
  * pci_read_vpd - Read one entry from Vital Product Data

drivers/pci/bus.c

@@ -41,9 +41,14 @@ pci_bus_alloc_resource(struct pci_bus *bus, struct resource *res,
 		void *alignf_data)
 {
 	int i, ret = -ENOMEM;
+	resource_size_t max = -1;
 
 	type_mask |= IORESOURCE_IO | IORESOURCE_MEM;
 
+	/* don't allocate too high if the pref mem doesn't support 64bit*/
+	if (!(res->flags & IORESOURCE_MEM_64))
+		max = PCIBIOS_MAX_MEM_32;
+
 	for (i = 0; i < PCI_BUS_NUM_RESOURCES; i++) {
 		struct resource *r = bus->resource[i];
 		if (!r)
@@ -62,7 +67,7 @@ pci_bus_alloc_resource(struct pci_bus *bus, struct resource *res,
 		/* Ok, try it out.. */
 		ret = allocate_resource(r, res, size,
 					r->start ? : min,
-					-1, align,
+					max, align,
 					alignf, alignf_data);
 		if (ret == 0)
 			break;
@@ -201,13 +206,18 @@ void pci_enable_bridges(struct pci_bus *bus)
  *  Walk the given bus, including any bridged devices
  *  on buses under this bus.  Call the provided callback
  *  on each device found.
+ *
+ *  We check the return of @cb each time. If it returns anything
+ *  other than 0, we break out.
+ *
  */
-void pci_walk_bus(struct pci_bus *top, void (*cb)(struct pci_dev *, void *),
+void pci_walk_bus(struct pci_bus *top, int (*cb)(struct pci_dev *, void *),
 		  void *userdata)
 {
 	struct pci_dev *dev;
 	struct pci_bus *bus;
 	struct list_head *next;
+	int retval;
 
 	bus = top;
 	down_read(&pci_bus_sem);
@@ -231,8 +241,10 @@ void pci_walk_bus(struct pci_bus *top, void (*cb)(struct pci_dev *, void *),
 
 		/* Run device routines with the device locked */
 		down(&dev->dev.sem);
-		cb(dev, userdata);
+		retval = cb(dev, userdata);
 		up(&dev->dev.sem);
+		if (retval)
+			break;
 	}
 	up_read(&pci_bus_sem);
 }

drivers/pci/hotplug/Kconfig

@@ -4,7 +4,7 @@
 
 menuconfig HOTPLUG_PCI
 	tristate "Support for PCI Hotplug"
-	depends on PCI && HOTPLUG
+	depends on PCI && HOTPLUG && SYSFS
 	---help---
 	  Say Y here if you have a motherboard with a PCI Hotplug controller.
 	  This allows you to add and remove PCI cards while the machine is
@@ -41,7 +41,7 @@ config HOTPLUG_PCI_FAKE
 
 config HOTPLUG_PCI_COMPAQ
 	tristate "Compaq PCI Hotplug driver"
-	depends on X86 && PCI_BIOS && PCI_LEGACY
+	depends on X86 && PCI_BIOS
 	help
 	  Say Y here if you have a motherboard with a Compaq PCI Hotplug
 	  controller.

drivers/pci/hotplug/acpiphp_core.c

@@ -77,7 +77,6 @@ static int get_latch_status	(struct hotplug_slot *slot, u8 *value);
 static int get_adapter_status	(struct hotplug_slot *slot, u8 *value);
 
 static struct hotplug_slot_ops acpi_hotplug_slot_ops = {
-	.owner			= THIS_MODULE,
 	.enable_slot		= enable_slot,
 	.disable_slot		= disable_slot,
 	.set_attention_status	= set_attention_status,

drivers/pci/hotplug/cpci_hotplug_core.c

@@ -72,7 +72,6 @@ static int get_adapter_status(struct hotplug_slot *slot, u8 * value);
 static int get_latch_status(struct hotplug_slot *slot, u8 * value);
 
 static struct hotplug_slot_ops cpci_hotplug_slot_ops = {
-	.owner = THIS_MODULE,
 	.enable_slot = enable_slot,
 	.disable_slot = disable_slot,
 	.set_attention_status = set_attention_status,

drivers/pci/hotplug/cpqphp_nvram.c

@@ -94,12 +94,13 @@ static u8 evbuffer[1024];
 
 static void __iomem *compaq_int15_entry_point;
 
-static spinlock_t int15_lock;		/* lock for ordering int15_bios_call() */
+/* lock for ordering int15_bios_call() */
+static spinlock_t int15_lock;
 
 
 /* This is a series of function that deals with
-   setting & getting the hotplug resource table in some environment variable.
-*/
+ * setting & getting the hotplug resource table in some environment variable.
+ */
 
 /*
  * We really shouldn't be doing this unless there is a _very_ good reason to!!!
@@ -113,7 +114,7 @@ static u32 add_byte( u32 **p_buffer, u8 value, u32 *used, u32 *avail)
 
 	if ((*used + 1) > *avail)
 		return(1);
-	
+
 	*((u8*)*p_buffer) = value;
 	tByte = (u8**)p_buffer;
 	(*tByte)++;
@@ -170,10 +171,10 @@ static u32 access_EV (u16 operation, u8 *ev_name, u8 *buffer, u32 *buf_size)
 	unsigned long flags;
 	int op = operation;
 	int ret_val;
-	
+
 	if (!compaq_int15_entry_point)
 		return -ENODEV;
-	
+
 	spin_lock_irqsave(&int15_lock, flags);
 	__asm__ (
 		"xorl   %%ebx,%%ebx\n" \
@@ -187,7 +188,7 @@ static u32 access_EV (u16 operation, u8 *ev_name, u8 *buffer, u32 *buf_size)
 		"D" (buffer), "m" (compaq_int15_entry_point)
 		: "%ebx", "%edx");
 	spin_unlock_irqrestore(&int15_lock, flags);
-	
+
 	return((ret_val & 0xFF00) >> 8);
 }
 
@@ -210,14 +211,16 @@ static int load_HRT (void __iomem *rom_start)
 
 	available = 1024;
 
-	// Now load the EV
+	/* Now load the EV */
 	temp_dword = available;
 
 	rc = access_EV(READ_EV, "CQTHPS", evbuffer, &temp_dword);
 
 	evbuffer_length = temp_dword;
 
-	// We're maintaining the resource lists so write FF to invalidate old info
+	/* We're maintaining the resource lists so write FF to invalidate old
+	 * info
+	 */
 	temp_dword = 1;
 
 	rc = access_EV(WRITE_EV, "CQTHPS", &temp_byte, &temp_dword);
@@ -263,13 +266,13 @@ static u32 store_HRT (void __iomem *rom_start)
 	p_EV_header = (struct ev_hrt_header *) pFill;
 
 	ctrl = cpqhp_ctrl_list;
-	
-	// The revision of this structure
+
+	/* The revision of this structure */
 	rc = add_byte( &pFill, 1 + ctrl->push_flag, &usedbytes, &available);
 	if (rc)
 		return(rc);
 
-	// The number of controllers
+	/* The number of controllers */
 	rc = add_byte( &pFill, 1, &usedbytes, &available);
 	if (rc)
 		return(rc);
@@ -279,27 +282,27 @@ static u32 store_HRT (void __iomem *rom_start)
 
 		numCtrl++;
 
-		// The bus number
+		/* The bus number */
 		rc = add_byte( &pFill, ctrl->bus, &usedbytes, &available);
 		if (rc)
 			return(rc);
 
-		// The device Number
+		/* The device Number */
 		rc = add_byte( &pFill, PCI_SLOT(ctrl->pci_dev->devfn), &usedbytes, &available);
 		if (rc)
 			return(rc);
 
-		// The function Number
+		/* The function Number */
 		rc = add_byte( &pFill, PCI_FUNC(ctrl->pci_dev->devfn), &usedbytes, &available);
 		if (rc)
 			return(rc);
 
-		// Skip the number of available entries
+		/* Skip the number of available entries */
 		rc = add_dword( &pFill, 0, &usedbytes, &available);
 		if (rc)
 			return(rc);
 
-		// Figure out memory Available
+		/* Figure out memory Available */
 
 		resNode = ctrl->mem_head;
 
@@ -308,12 +311,12 @@ static u32 store_HRT (void __iomem *rom_start)
 		while (resNode) {
 			loop ++;
 
-			// base
+			/* base */
 			rc = add_dword( &pFill, resNode->base, &usedbytes, &available);
 			if (rc)
 				return(rc);
 
-			// length
+			/* length */
 			rc = add_dword( &pFill, resNode->length, &usedbytes, &available);
 			if (rc)
 				return(rc);
@@ -321,10 +324,10 @@ static u32 store_HRT (void __iomem *rom_start)
 			resNode = resNode->next;
 		}
 
-		// Fill in the number of entries
+		/* Fill in the number of entries */
 		p_ev_ctrl->mem_avail = loop;
 
-		// Figure out prefetchable memory Available
+		/* Figure out prefetchable memory Available */
 
 		resNode = ctrl->p_mem_head;
 
@@ -333,12 +336,12 @@ static u32 store_HRT (void __iomem *rom_start)
 		while (resNode) {
 			loop ++;
 
-			// base
+			/* base */
 			rc = add_dword( &pFill, resNode->base, &usedbytes, &available);
 			if (rc)
 				return(rc);
 
-			// length
+			/* length */
 			rc = add_dword( &pFill, resNode->length, &usedbytes, &available);
 			if (rc)
 				return(rc);
@@ -346,10 +349,10 @@ static u32 store_HRT (void __iomem *rom_start)
 			resNode = resNode->next;
 		}
 
-		// Fill in the number of entries
+		/* Fill in the number of entries */
 		p_ev_ctrl->p_mem_avail = loop;
 
-		// Figure out IO Available
+		/* Figure out IO Available */
 
 		resNode = ctrl->io_head;
 
@@ -358,12 +361,12 @@ static u32 store_HRT (void __iomem *rom_start)
 		while (resNode) {
 			loop ++;
 
-			// base
+			/* base */
 			rc = add_dword( &pFill, resNode->base, &usedbytes, &available);
 			if (rc)
 				return(rc);
 
-			// length
+			/* length */
 			rc = add_dword( &pFill, resNode->length, &usedbytes, &available);
 			if (rc)
 				return(rc);
@@ -371,10 +374,10 @@ static u32 store_HRT (void __iomem *rom_start)
 			resNode = resNode->next;
 		}
 
-		// Fill in the number of entries
+		/* Fill in the number of entries */
 		p_ev_ctrl->io_avail = loop;
 
-		// Figure out bus Available
+		/* Figure out bus Available */
 
 		resNode = ctrl->bus_head;
 
@@ -383,12 +386,12 @@ static u32 store_HRT (void __iomem *rom_start)
 		while (resNode) {
 			loop ++;
 
-			// base
+			/* base */
 			rc = add_dword( &pFill, resNode->base, &usedbytes, &available);
 			if (rc)
 				return(rc);
 
-			// length
+			/* length */
 			rc = add_dword( &pFill, resNode->length, &usedbytes, &available);
 			if (rc)
 				return(rc);
@@ -396,15 +399,15 @@ static u32 store_HRT (void __iomem *rom_start)
 			resNode = resNode->next;
 		}
 
-		// Fill in the number of entries
+		/* Fill in the number of entries */
 		p_ev_ctrl->bus_avail = loop;
 
 		ctrl = ctrl->next;
 	}
-	
+
 	p_EV_header->num_of_ctrl = numCtrl;
 
-	// Now store the EV
+	/* Now store the EV */
 
 	temp_dword = usedbytes;
 
@@ -449,20 +452,21 @@ int compaq_nvram_load (void __iomem *rom_start, struct controller *ctrl)
 	struct ev_hrt_header *p_EV_header;
 
 	if (!evbuffer_init) {
-		// Read the resource list information in from NVRAM
+		/* Read the resource list information in from NVRAM */
 		if (load_HRT(rom_start))
 			memset (evbuffer, 0, 1024);
 
 		evbuffer_init = 1;
 	}
 
-	// If we saved information in NVRAM, use it now
+	/* If we saved information in NVRAM, use it now */
 	p_EV_header = (struct ev_hrt_header *) evbuffer;
 
-	// The following code is for systems where version 1.0 of this
-	// driver has been loaded, but doesn't support the hardware.
-	// In that case, the driver would incorrectly store something
-	// in NVRAM.
+	/* The following code is for systems where version 1.0 of this
+	 * driver has been loaded, but doesn't support the hardware.
+	 * In that case, the driver would incorrectly store something
+	 * in NVRAM.
+	 */
 	if ((p_EV_header->Version == 2) ||
 	    ((p_EV_header->Version == 1) && !ctrl->push_flag)) {
 		p_byte = &(p_EV_header->next);
@@ -479,7 +483,7 @@ int compaq_nvram_load (void __iomem *rom_start, struct controller *ctrl)
 		function = p_ev_ctrl->function;
 
 		while ((bus != ctrl->bus) ||
-		       (device != PCI_SLOT(ctrl->pci_dev->devfn)) || 
+		       (device != PCI_SLOT(ctrl->pci_dev->devfn)) ||
 		       (function != PCI_FUNC(ctrl->pci_dev->devfn))) {
 			nummem = p_ev_ctrl->mem_avail;
 			numpmem = p_ev_ctrl->p_mem_avail;
@@ -491,7 +495,7 @@ int compaq_nvram_load (void __iomem *rom_start, struct controller *ctrl)
 			if (p_byte > ((u8*)p_EV_header + evbuffer_length))
 				return 2;
 
-			// Skip forward to the next entry
+			/* Skip forward to the next entry */
 			p_byte += (nummem + numpmem + numio + numbus) * 8;
 
 			if (p_byte > ((u8*)p_EV_header + evbuffer_length))
@@ -629,8 +633,9 @@ int compaq_nvram_load (void __iomem *rom_start, struct controller *ctrl)
 			ctrl->bus_head = bus_node;
 		}
 
-		// If all of the following fail, we don't have any resources for
-		// hot plug add
+		/* If all of the following fail, we don't have any resources for
+		 * hot plug add
+		 */
 		rc = 1;
 		rc &= cpqhp_resource_sort_and_combine(&(ctrl->mem_head));
 		rc &= cpqhp_resource_sort_and_combine(&(ctrl->p_mem_head));
@@ -640,14 +645,14 @@ int compaq_nvram_load (void __iomem *rom_start, struct controller *ctrl)
 		if (rc)
 			return(rc);
 	} else {
-		if ((evbuffer[0] != 0) && (!ctrl->push_flag)) 
+		if ((evbuffer[0] != 0) && (!ctrl->push_flag))
 			return 1;
 	}
 
 	return 0;
 }
 
-	
+
 int compaq_nvram_store (void __iomem *rom_start)
 {
 	int rc = 1;

drivers/pci/hotplug/ibmphp_core.c

@@ -1318,7 +1318,6 @@ int ibmphp_do_disable_slot(struct slot *slot_cur)
 }
 
 struct hotplug_slot_ops ibmphp_hotplug_slot_ops = {
-	.owner =			THIS_MODULE,
 	.set_attention_status =		set_attention_status,
 	.enable_slot =			enable_slot,
 	.disable_slot =			ibmphp_disable_slot,
@@ -1421,3 +1420,4 @@ static void __exit ibmphp_exit(void)
 }
 
 module_init(ibmphp_init);
+module_exit(ibmphp_exit);

drivers/pci/hotplug/pci_hotplug_core.c

@@ -347,125 +347,129 @@ static struct pci_slot_attribute hotplug_slot_attr_test = {
 	.store = test_write_file
 };
 
-static int has_power_file(struct pci_slot *pci_slot)
+static bool has_power_file(struct pci_slot *pci_slot)
 {
 	struct hotplug_slot *slot = pci_slot->hotplug;
 	if ((!slot) || (!slot->ops))
-		return -ENODEV;
+		return false;
 	if ((slot->ops->enable_slot) ||
 	    (slot->ops->disable_slot) ||
 	    (slot->ops->get_power_status))
-		return 0;
-	return -ENOENT;
+		return true;
+	return false;
 }
 
-static int has_attention_file(struct pci_slot *pci_slot)
+static bool has_attention_file(struct pci_slot *pci_slot)
 {
 	struct hotplug_slot *slot = pci_slot->hotplug;
 	if ((!slot) || (!slot->ops))
-		return -ENODEV;
+		return false;
 	if ((slot->ops->set_attention_status) ||
 	    (slot->ops->get_attention_status))
-		return 0;
-	return -ENOENT;
+		return true;
+	return false;
 }
 
-static int has_latch_file(struct pci_slot *pci_slot)
+static bool has_latch_file(struct pci_slot *pci_slot)
 {
 	struct hotplug_slot *slot = pci_slot->hotplug;
 	if ((!slot) || (!slot->ops))
-		return -ENODEV;
+		return false;
 	if (slot->ops->get_latch_status)
-		return 0;
-	return -ENOENT;
+		return true;
+	return false;
 }
 
-static int has_adapter_file(struct pci_slot *pci_slot)
+static bool has_adapter_file(struct pci_slot *pci_slot)
 {
 	struct hotplug_slot *slot = pci_slot->hotplug;
 	if ((!slot) || (!slot->ops))
-		return -ENODEV;
+		return false;
 	if (slot->ops->get_adapter_status)
-		return 0;
-	return -ENOENT;
+		return true;
+	return false;
 }
 
-static int has_max_bus_speed_file(struct pci_slot *pci_slot)
+static bool has_max_bus_speed_file(struct pci_slot *pci_slot)
 {
 	struct hotplug_slot *slot = pci_slot->hotplug;
 	if ((!slot) || (!slot->ops))
-		return -ENODEV;
+		return false;
 	if (slot->ops->get_max_bus_speed)
-		return 0;
-	return -ENOENT;
+		return true;
+	return false;
 }
 
-static int has_cur_bus_speed_file(struct pci_slot *pci_slot)
+static bool has_cur_bus_speed_file(struct pci_slot *pci_slot)
 {
 	struct hotplug_slot *slot = pci_slot->hotplug;
 	if ((!slot) || (!slot->ops))
-		return -ENODEV;
+		return false;
 	if (slot->ops->get_cur_bus_speed)
-		return 0;
-	return -ENOENT;
+		return true;
+	return false;
 }
 
-static int has_test_file(struct pci_slot *pci_slot)
+static bool has_test_file(struct pci_slot *pci_slot)
 {
 	struct hotplug_slot *slot = pci_slot->hotplug;
 	if ((!slot) || (!slot->ops))
-		return -ENODEV;
+		return false;
 	if (slot->ops->hardware_test)
-		return 0;
-	return -ENOENT;
+		return true;
+	return false;
 }
 
 static int fs_add_slot(struct pci_slot *slot)
 {
 	int retval = 0;
 
-	if (has_power_file(slot) == 0) {
-		retval = sysfs_create_file(&slot->kobj, &hotplug_slot_attr_power.attr);
+	/* Create symbolic link to the hotplug driver module */
+	pci_hp_create_module_link(slot);
+
+	if (has_power_file(slot)) {
+		retval = sysfs_create_file(&slot->kobj,
+					   &hotplug_slot_attr_power.attr);
 		if (retval)
 			goto exit_power;
 	}
 
-	if (has_attention_file(slot) == 0) {
+	if (has_attention_file(slot)) {
 		retval = sysfs_create_file(&slot->kobj,
 					   &hotplug_slot_attr_attention.attr);
 		if (retval)
 			goto exit_attention;
 	}
 
-	if (has_latch_file(slot) == 0) {
+	if (has_latch_file(slot)) {
 		retval = sysfs_create_file(&slot->kobj,
 					   &hotplug_slot_attr_latch.attr);
 		if (retval)
 			goto exit_latch;
 	}
 
-	if (has_adapter_file(slot) == 0) {
+	if (has_adapter_file(slot)) {
 		retval = sysfs_create_file(&slot->kobj,
 					   &hotplug_slot_attr_presence.attr);
 		if (retval)
 			goto exit_adapter;
 	}
 
-	if (has_max_bus_speed_file(slot) == 0) {
+	if (has_max_bus_speed_file(slot)) {
 		retval = sysfs_create_file(&slot->kobj,
-					   &hotplug_slot_attr_max_bus_speed.attr);
+					&hotplug_slot_attr_max_bus_speed.attr);
 		if (retval)
 			goto exit_max_speed;
 	}
 
-	if (has_cur_bus_speed_file(slot) == 0) {
+	if (has_cur_bus_speed_file(slot)) {
 		retval = sysfs_create_file(&slot->kobj,
-					   &hotplug_slot_attr_cur_bus_speed.attr);
+					&hotplug_slot_attr_cur_bus_speed.attr);
 		if (retval)
 			goto exit_cur_speed;
 	}
 
-	if (has_test_file(slot) == 0) {
+	if (has_test_file(slot)) {
 		retval = sysfs_create_file(&slot->kobj,
 					   &hotplug_slot_attr_test.attr);
 		if (retval)
@@ -475,55 +479,61 @@ static int fs_add_slot(struct pci_slot *slot)
 	goto exit;
 
 exit_test:
-	if (has_cur_bus_speed_file(slot) == 0)
-		sysfs_remove_file(&slot->kobj, &hotplug_slot_attr_cur_bus_speed.attr);
-
+	if (has_cur_bus_speed_file(slot))
+		sysfs_remove_file(&slot->kobj,
+				  &hotplug_slot_attr_cur_bus_speed.attr);
 exit_cur_speed:
-	if (has_max_bus_speed_file(slot) == 0)
-		sysfs_remove_file(&slot->kobj, &hotplug_slot_attr_max_bus_speed.attr);
-
+	if (has_max_bus_speed_file(slot))
+		sysfs_remove_file(&slot->kobj,
+				  &hotplug_slot_attr_max_bus_speed.attr);
 exit_max_speed:
-	if (has_adapter_file(slot) == 0)
-		sysfs_remove_file(&slot->kobj, &hotplug_slot_attr_presence.attr);
-
+	if (has_adapter_file(slot))
+		sysfs_remove_file(&slot->kobj,
+				  &hotplug_slot_attr_presence.attr);
 exit_adapter:
-	if (has_latch_file(slot) == 0)
+	if (has_latch_file(slot))
 		sysfs_remove_file(&slot->kobj, &hotplug_slot_attr_latch.attr);
-
 exit_latch:
-	if (has_attention_file(slot) == 0)
-		sysfs_remove_file(&slot->kobj, &hotplug_slot_attr_attention.attr);
-
+	if (has_attention_file(slot))
+		sysfs_remove_file(&slot->kobj,
+				  &hotplug_slot_attr_attention.attr);
 exit_attention:
-	if (has_power_file(slot) == 0)
+	if (has_power_file(slot))
 		sysfs_remove_file(&slot->kobj, &hotplug_slot_attr_power.attr);
 exit_power:
+	pci_hp_remove_module_link(slot);
 exit:
 	return retval;
 }
 
 static void fs_remove_slot(struct pci_slot *slot)
 {
-	if (has_power_file(slot) == 0)
+	if (has_power_file(slot))
 		sysfs_remove_file(&slot->kobj, &hotplug_slot_attr_power.attr);
 
-	if (has_attention_file(slot) == 0)
-		sysfs_remove_file(&slot->kobj, &hotplug_slot_attr_attention.attr);
+	if (has_attention_file(slot))
+		sysfs_remove_file(&slot->kobj,
+				  &hotplug_slot_attr_attention.attr);
 
-	if (has_latch_file(slot) == 0)
+	if (has_latch_file(slot))
 		sysfs_remove_file(&slot->kobj, &hotplug_slot_attr_latch.attr);
 
-	if (has_adapter_file(slot) == 0)
-		sysfs_remove_file(&slot->kobj, &hotplug_slot_attr_presence.attr);
+	if (has_adapter_file(slot))
+		sysfs_remove_file(&slot->kobj,
+				  &hotplug_slot_attr_presence.attr);
 
-	if (has_max_bus_speed_file(slot) == 0)
-		sysfs_remove_file(&slot->kobj, &hotplug_slot_attr_max_bus_speed.attr);
+	if (has_max_bus_speed_file(slot))
+		sysfs_remove_file(&slot->kobj,
+				  &hotplug_slot_attr_max_bus_speed.attr);
 
-	if (has_cur_bus_speed_file(slot) == 0)
-		sysfs_remove_file(&slot->kobj, &hotplug_slot_attr_cur_bus_speed.attr);
+	if (has_cur_bus_speed_file(slot))
+		sysfs_remove_file(&slot->kobj,
+				  &hotplug_slot_attr_cur_bus_speed.attr);
 
-	if (has_test_file(slot) == 0)
+	if (has_test_file(slot))
 		sysfs_remove_file(&slot->kobj, &hotplug_slot_attr_test.attr);
+
+	pci_hp_remove_module_link(slot);
 }
 
 static struct hotplug_slot *get_slot_from_name (const char *name)
@@ -540,10 +550,10 @@ static struct hotplug_slot *get_slot_from_name (const char *name)
 }
 
 /**
- * pci_hp_register - register a hotplug_slot with the PCI hotplug subsystem
+ * __pci_hp_register - register a hotplug_slot with the PCI hotplug subsystem
  * @bus: bus this slot is on
  * @slot: pointer to the &struct hotplug_slot to register
- * @slot_nr: slot number
+ * @devnr: device number
  * @name: name registered with kobject core
  *
  * Registers a hotplug slot with the pci hotplug subsystem, which will allow
@@ -551,8 +561,9 @@ static struct hotplug_slot *get_slot_from_name (const char *name)
  *
  * Returns 0 if successful, anything else for an error.
  */
-int pci_hp_register(struct hotplug_slot *slot, struct pci_bus *bus, int slot_nr,
-			const char *name)
+int __pci_hp_register(struct hotplug_slot *slot, struct pci_bus *bus,
+		      int devnr, const char *name,
+		      struct module *owner, const char *mod_name)
 {
 	int result;
 	struct pci_slot *pci_slot;
@@ -567,14 +578,16 @@ int pci_hp_register(struct hotplug_slot *slot, struct pci_bus *bus, int slot_nr,
 		return -EINVAL;
 	}
 
-	mutex_lock(&pci_hp_mutex);
+	slot->ops->owner = owner;
+	slot->ops->mod_name = mod_name;
 
+	mutex_lock(&pci_hp_mutex);
 	/*
 	 * No problems if we call this interface from both ACPI_PCI_SLOT
 	 * driver and call it here again. If we've already created the
 	 * pci_slot, the interface will simply bump the refcount.
 	 */
-	pci_slot = pci_create_slot(bus, slot_nr, name, slot);
+	pci_slot = pci_create_slot(bus, devnr, name, slot);
 	if (IS_ERR(pci_slot)) {
 		result = PTR_ERR(pci_slot);
 		goto out;
@@ -684,6 +697,6 @@ MODULE_LICENSE("GPL");
 module_param(debug, bool, 0644);
 MODULE_PARM_DESC(debug, "Debugging mode enabled or not");
 
-EXPORT_SYMBOL_GPL(pci_hp_register);
+EXPORT_SYMBOL_GPL(__pci_hp_register);
 EXPORT_SYMBOL_GPL(pci_hp_deregister);
 EXPORT_SYMBOL_GPL(pci_hp_change_slot_info);

drivers/pci/hotplug/pciehp.h

@@ -81,7 +81,6 @@ struct slot {
 	struct hpc_ops *hpc_ops;
 	struct hotplug_slot *hotplug_slot;
 	struct list_head	slot_list;
-	unsigned long last_emi_toggle;
 	struct delayed_work work;	/* work for button event */
 	struct mutex lock;
 };
@@ -203,8 +202,6 @@ struct hpc_ops {
 	int (*set_attention_status)(struct slot *slot, u8 status);
 	int (*get_latch_status)(struct slot *slot, u8 *status);
 	int (*get_adapter_status)(struct slot *slot, u8 *status);
-	int (*get_emi_status)(struct slot *slot, u8 *status);
-	int (*toggle_emi)(struct slot *slot);
 	int (*get_max_bus_speed)(struct slot *slot, enum pci_bus_speed *speed);
 	int (*get_cur_bus_speed)(struct slot *slot, enum pci_bus_speed *speed);
 	int (*get_max_lnk_width)(struct slot *slot, enum pcie_link_width *val);

drivers/pci/hotplug/pciehp_core.c

@@ -73,7 +73,6 @@ static int get_max_bus_speed	(struct hotplug_slot *slot, enum pci_bus_speed *val
 static int get_cur_bus_speed	(struct hotplug_slot *slot, enum pci_bus_speed *value);
 
 static struct hotplug_slot_ops pciehp_hotplug_slot_ops = {
-	.owner =		THIS_MODULE,
 	.set_attention_status =	set_attention_status,
 	.enable_slot =		enable_slot,
 	.disable_slot =		disable_slot,
@@ -85,99 +84,6 @@ static struct hotplug_slot_ops pciehp_hotplug_slot_ops = {
   	.get_cur_bus_speed =	get_cur_bus_speed,
 };
 
-/*
- * Check the status of the Electro Mechanical Interlock (EMI)
- */
-static int get_lock_status(struct hotplug_slot *hotplug_slot, u8 *value)
-{
-	struct slot *slot = hotplug_slot->private;
-	return (slot->hpc_ops->get_emi_status(slot, value));
-}
-
-/*
- * sysfs interface for the Electro Mechanical Interlock (EMI)
- * 1 == locked, 0 == unlocked
- */
-static ssize_t lock_read_file(struct hotplug_slot *slot, char *buf)
-{
-	int retval;
-	u8 value;
-
-	retval = get_lock_status(slot, &value);
-	if (retval)
-		goto lock_read_exit;
-	retval = sprintf (buf, "%d\n", value);
-
-lock_read_exit:
-	return retval;
-}
-
-/*
- * Change the status of the Electro Mechanical Interlock (EMI)
- * This is a toggle - in addition there must be at least 1 second
- * in between toggles.
- */
-static int set_lock_status(struct hotplug_slot *hotplug_slot, u8 status)
-{
-	struct slot *slot = hotplug_slot->private;
-	int retval;
-	u8 value;
-
-	mutex_lock(&slot->ctrl->crit_sect);
-
-	/* has it been >1 sec since our last toggle? */
-	if ((get_seconds() - slot->last_emi_toggle) < 1) {
-		mutex_unlock(&slot->ctrl->crit_sect);
-		return -EINVAL;
-	}
-
-	/* see what our current state is */
-	retval = get_lock_status(hotplug_slot, &value);
-	if (retval || (value == status))
-		goto set_lock_exit;
-
-	slot->hpc_ops->toggle_emi(slot);
-set_lock_exit:
-	mutex_unlock(&slot->ctrl->crit_sect);
-	return 0;
-}
-
-/*
- * sysfs interface which allows the user to toggle the Electro Mechanical
- * Interlock.  Valid values are either 0 or 1.  0 == unlock, 1 == lock
- */
-static ssize_t lock_write_file(struct hotplug_slot *hotplug_slot,
-		const char *buf, size_t count)
-{
-	struct slot *slot = hotplug_slot->private;
-	unsigned long llock;
-	u8 lock;
-	int retval = 0;
-
-	llock = simple_strtoul(buf, NULL, 10);
-	lock = (u8)(llock & 0xff);
-
-	switch (lock) {
-		case 0:
-		case 1:
-			retval = set_lock_status(hotplug_slot, lock);
-			break;
-		default:
-			ctrl_err(slot->ctrl, "%d is an invalid lock value\n",
-				 lock);
-			retval = -EINVAL;
-	}
-	if (retval)
-		return retval;
-	return count;
-}
-
-static struct hotplug_slot_attribute hotplug_slot_attr_lock = {
-	.attr = {.name = "lock", .mode = S_IFREG | S_IRUGO | S_IWUSR},
-	.show = lock_read_file,
-	.store = lock_write_file
-};
-
 /**
  * release_slot - free up the memory used by a slot
  * @hotplug_slot: slot to free
@@ -236,17 +142,6 @@ static int init_slots(struct controller *ctrl)
 		get_attention_status(hotplug_slot, &info->attention_status);
 		get_latch_status(hotplug_slot, &info->latch_status);
 		get_adapter_status(hotplug_slot, &info->adapter_status);
-		/* create additional sysfs entries */
-		if (EMI(ctrl)) {
-			retval = sysfs_create_file(&hotplug_slot->pci_slot->kobj,
-				&hotplug_slot_attr_lock.attr);
-			if (retval) {
-				pci_hp_deregister(hotplug_slot);
-				ctrl_err(ctrl, "Cannot create additional sysfs "
-					 "entries\n");
-				goto error_info;
-			}
-		}
 	}
 
 	return 0;
@@ -261,13 +156,8 @@ static int init_slots(struct controller *ctrl)
 static void cleanup_slots(struct controller *ctrl)
 {
 	struct slot *slot;
-
-	list_for_each_entry(slot, &ctrl->slot_list, slot_list) {
-		if (EMI(ctrl))
-			sysfs_remove_file(&slot->hotplug_slot->pci_slot->kobj,
-				&hotplug_slot_attr_lock.attr);
+	list_for_each_entry(slot, &ctrl->slot_list, slot_list)
 		pci_hp_deregister(slot->hotplug_slot);
-	}
 }
 
 /*

drivers/pci/hotplug/pciehp_hpc.c

@@ -422,35 +422,6 @@ static int hpc_query_power_fault(struct slot *slot)
 	return !!(slot_status & PCI_EXP_SLTSTA_PFD);
 }
 
-static int hpc_get_emi_status(struct slot *slot, u8 *status)
-{
-	struct controller *ctrl = slot->ctrl;
-	u16 slot_status;
-	int retval;
-
-	retval = pciehp_readw(ctrl, PCI_EXP_SLTSTA, &slot_status);
-	if (retval) {
-		ctrl_err(ctrl, "Cannot check EMI status\n");
-		return retval;
-	}
-	*status = !!(slot_status & PCI_EXP_SLTSTA_EIS);
-	return retval;
-}
-
-static int hpc_toggle_emi(struct slot *slot)
-{
-	u16 slot_cmd;
-	u16 cmd_mask;
-	int rc;
-
-	slot_cmd = PCI_EXP_SLTCTL_EIC;
-	cmd_mask = PCI_EXP_SLTCTL_EIC;
-	rc = pcie_write_cmd(slot->ctrl, slot_cmd, cmd_mask);
-	slot->last_emi_toggle = get_seconds();
-
-	return rc;
-}
-
 static int hpc_set_attention_status(struct slot *slot, u8 value)
 {
 	struct controller *ctrl = slot->ctrl;
@@ -874,8 +845,6 @@ static struct hpc_ops pciehp_hpc_ops = {
 	.get_attention_status		= hpc_get_attention_status,
 	.get_latch_status		= hpc_get_latch_status,
 	.get_adapter_status		= hpc_get_adapter_status,
-	.get_emi_status			= hpc_get_emi_status,
-	.toggle_emi			= hpc_toggle_emi,
 
 	.get_max_bus_speed		= hpc_get_max_lnk_speed,
 	.get_cur_bus_speed		= hpc_get_cur_lnk_speed,

drivers/pci/hotplug/pcihp_skeleton.c

@@ -82,7 +82,6 @@ static int get_latch_status	(struct hotplug_slot *slot, u8 *value);
 static int get_adapter_status	(struct hotplug_slot *slot, u8 *value);
 
 static struct hotplug_slot_ops skel_hotplug_slot_ops = {
-	.owner =		THIS_MODULE,
 	.enable_slot =		enable_slot,
 	.disable_slot =		disable_slot,
 	.set_attention_status =	set_attention_status,

drivers/pci/hotplug/rpaphp_core.c

@@ -423,7 +423,6 @@ static int disable_slot(struct hotplug_slot *hotplug_slot)
 }
 
 struct hotplug_slot_ops rpaphp_hotplug_slot_ops = {
-	.owner = THIS_MODULE,
 	.enable_slot = enable_slot,
 	.disable_slot = disable_slot,
 	.set_attention_status = set_attention_status,

drivers/pci/hotplug/sgi_hotplug.c

@@ -83,7 +83,6 @@ static int disable_slot(struct hotplug_slot *slot);
 static inline int get_power_status(struct hotplug_slot *slot, u8 *value);
 
 static struct hotplug_slot_ops sn_hotplug_slot_ops = {
-	.owner                  = THIS_MODULE,
 	.enable_slot            = enable_slot,
 	.disable_slot           = disable_slot,
 	.get_power_status       = get_power_status,

drivers/pci/hotplug/shpchp_core.c

@@ -69,7 +69,6 @@ static int get_max_bus_speed	(struct hotplug_slot *slot, enum pci_bus_speed *val
 static int get_cur_bus_speed	(struct hotplug_slot *slot, enum pci_bus_speed *value);
 
 static struct hotplug_slot_ops shpchp_hotplug_slot_ops = {
-	.owner =		THIS_MODULE,
 	.set_attention_status =	set_attention_status,
 	.enable_slot =		enable_slot,
 	.disable_slot =		disable_slot,