davinci: fix DEBUG_LL code for p2v changes

Fixup davinci UART low-level debug code for new ARM generic p2v changes.

Based on OMAP changes by Tony Lindgren

Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

arch/arm/mach-davinci/include/mach/debug-macro.S

@@ -24,6 +24,9 @@
 
 #define UART_SHIFT	2
 
+#define davinci_uart_v2p(x)	((x) - PAGE_OFFSET + PLAT_PHYS_OFFSET)
+#define davinci_uart_p2v(x)	((x) - PLAT_PHYS_OFFSET + PAGE_OFFSET)
+
 		.pushsection .data
 davinci_uart_phys:	.word	0
 davinci_uart_virt:	.word	0
@@ -34,7 +37,7 @@ davinci_uart_virt:	.word	0
 		/* Use davinci_uart_phys/virt if already configured */
 10:		mrc	p15, 0, \rp, c1, c0
 		tst	\rp, #1			@ MMU enabled?
-		ldreq	\rp, =__virt_to_phys(davinci_uart_phys)
+		ldreq	\rp, =davinci_uart_v2p(davinci_uart_phys)
 		ldrne	\rp, =davinci_uart_phys
 		add	\rv, \rp, #4		@ davinci_uart_virt
 		ldr	\rp, [\rp, #0]
@@ -48,18 +51,18 @@ davinci_uart_virt:	.word	0
 		tst	\rp, #1			@ MMU enabled?
 
 		/* Copy uart phys address from decompressor uart info */
-		ldreq	\rv, =__virt_to_phys(davinci_uart_phys)
+		ldreq	\rv, =davinci_uart_v2p(davinci_uart_phys)
 		ldrne	\rv, =davinci_uart_phys
 		ldreq	\rp, =DAVINCI_UART_INFO
-		ldrne	\rp, =__phys_to_virt(DAVINCI_UART_INFO)
+		ldrne	\rp, =davinci_uart_p2v(DAVINCI_UART_INFO)
 		ldr	\rp, [\rp, #0]
 		str	\rp, [\rv]
 
 		/* Copy uart virt address from decompressor uart info */
-		ldreq	\rv, =__virt_to_phys(davinci_uart_virt)
+		ldreq	\rv, =davinci_uart_v2p(davinci_uart_virt)
 		ldrne	\rv, =davinci_uart_virt
 		ldreq	\rp, =DAVINCI_UART_INFO
-		ldrne	\rp, =__phys_to_virt(DAVINCI_UART_INFO)
+		ldrne	\rp, =davinci_uart_p2v(DAVINCI_UART_INFO)
 		ldr	\rp, [\rp, #4]
 		str	\rp, [\rv]
 

arch/arm/mach-davinci/include/mach/serial.h

@@ -22,7 +22,7 @@
  *
  * This area sits just below the page tables (see arch/arm/kernel/head.S).
  */
-#define DAVINCI_UART_INFO	(PHYS_OFFSET + 0x3ff8)
+#define DAVINCI_UART_INFO	(PLAT_PHYS_OFFSET + 0x3ff8)
 
 #define DAVINCI_UART0_BASE	(IO_PHYS + 0x20000)
 #define DAVINCI_UART1_BASE	(IO_PHYS + 0x20400)