Merge tag 'mmc-v5.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc

Pull MMC fixes from Ulf Hansson:
 "A couple of MMC fixes:

   - sdhci-of-arasan: Stabilize communication by fixing tap value configs

   - sdhci-pci: Use SDR25 timing for HS mode for BYT-based Intel HWs"

* tag 'mmc-v5.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: sdhci-of-arasan: Issue DLL reset explicitly
  mmc: sdhci-of-arasan: Use Mask writes for Tap delays
  mmc: sdhci-of-arasan: Allow configuring zero tap values
  mmc: sdhci-pci: Prefer SDR25 timing for High Speed mode for BYT-based Intel controllers

drivers/mmc/host/sdhci-of-arasan.c

@@ -30,7 +30,10 @@
 #define SDHCI_ARASAN_VENDOR_REGISTER	0x78
 
 #define SDHCI_ARASAN_ITAPDLY_REGISTER	0xF0F8
+#define SDHCI_ARASAN_ITAPDLY_SEL_MASK	0xFF
+
 #define SDHCI_ARASAN_OTAPDLY_REGISTER	0xF0FC
+#define SDHCI_ARASAN_OTAPDLY_SEL_MASK	0x3F
 
 #define SDHCI_ARASAN_CQE_BASE_ADDR	0x200
 #define VENDOR_ENHANCED_STROBE		BIT(0)
@@ -600,14 +603,8 @@ static int sdhci_zynqmp_sdcardclk_set_phase(struct clk_hw *hw, int degrees)
 	u8 tap_delay, tap_max = 0;
 	int ret;
 
-	/*
-	 * This is applicable for SDHCI_SPEC_300 and above
-	 * ZynqMP does not set phase for <=25MHz clock.
-	 * If degrees is zero, no need to do anything.
-	 */
-	if (host->version < SDHCI_SPEC_300 ||
-	    host->timing == MMC_TIMING_LEGACY ||
-	    host->timing == MMC_TIMING_UHS_SDR12 || !degrees)
+	/* This is applicable for SDHCI_SPEC_300 and above */
+	if (host->version < SDHCI_SPEC_300)
 		return 0;
 
 	switch (host->timing) {
@@ -638,6 +635,9 @@ static int sdhci_zynqmp_sdcardclk_set_phase(struct clk_hw *hw, int degrees)
 	if (ret)
 		pr_err("Error setting Output Tap Delay\n");
 
+	/* Release DLL Reset */
+	zynqmp_pm_sd_dll_reset(node_id, PM_DLL_RESET_RELEASE);
+
 	return ret;
 }
 
@@ -668,16 +668,13 @@ static int sdhci_zynqmp_sampleclk_set_phase(struct clk_hw *hw, int degrees)
 	u8 tap_delay, tap_max = 0;
 	int ret;
 
-	/*
-	 * This is applicable for SDHCI_SPEC_300 and above
-	 * ZynqMP does not set phase for <=25MHz clock.
-	 * If degrees is zero, no need to do anything.
-	 */
-	if (host->version < SDHCI_SPEC_300 ||
-	    host->timing == MMC_TIMING_LEGACY ||
-	    host->timing == MMC_TIMING_UHS_SDR12 || !degrees)
+	/* This is applicable for SDHCI_SPEC_300 and above */
+	if (host->version < SDHCI_SPEC_300)
 		return 0;
 
+	/* Assert DLL Reset */
+	zynqmp_pm_sd_dll_reset(node_id, PM_DLL_RESET_ASSERT);
+
 	switch (host->timing) {
 	case MMC_TIMING_MMC_HS:
 	case MMC_TIMING_SD_HS:
@@ -733,14 +730,8 @@ static int sdhci_versal_sdcardclk_set_phase(struct clk_hw *hw, int degrees)
 	struct sdhci_host *host = sdhci_arasan->host;
 	u8 tap_delay, tap_max = 0;
 
-	/*
-	 * This is applicable for SDHCI_SPEC_300 and above
-	 * Versal does not set phase for <=25MHz clock.
-	 * If degrees is zero, no need to do anything.
-	 */
-	if (host->version < SDHCI_SPEC_300 ||
-	    host->timing == MMC_TIMING_LEGACY ||
-	    host->timing == MMC_TIMING_UHS_SDR12 || !degrees)
+	/* This is applicable for SDHCI_SPEC_300 and above */
+	if (host->version < SDHCI_SPEC_300)
 		return 0;
 
 	switch (host->timing) {
@@ -773,6 +764,7 @@ static int sdhci_versal_sdcardclk_set_phase(struct clk_hw *hw, int degrees)
 		regval = sdhci_readl(host, SDHCI_ARASAN_OTAPDLY_REGISTER);
 		regval |= SDHCI_OTAPDLY_ENABLE;
 		sdhci_writel(host, regval, SDHCI_ARASAN_OTAPDLY_REGISTER);
+		regval &= ~SDHCI_ARASAN_OTAPDLY_SEL_MASK;
 		regval |= tap_delay;
 		sdhci_writel(host, regval, SDHCI_ARASAN_OTAPDLY_REGISTER);
 	}
@@ -804,14 +796,8 @@ static int sdhci_versal_sampleclk_set_phase(struct clk_hw *hw, int degrees)
 	struct sdhci_host *host = sdhci_arasan->host;
 	u8 tap_delay, tap_max = 0;
 
-	/*
-	 * This is applicable for SDHCI_SPEC_300 and above
-	 * Versal does not set phase for <=25MHz clock.
-	 * If degrees is zero, no need to do anything.
-	 */
-	if (host->version < SDHCI_SPEC_300 ||
-	    host->timing == MMC_TIMING_LEGACY ||
-	    host->timing == MMC_TIMING_UHS_SDR12 || !degrees)
+	/* This is applicable for SDHCI_SPEC_300 and above */
+	if (host->version < SDHCI_SPEC_300)
 		return 0;
 
 	switch (host->timing) {
@@ -846,6 +832,7 @@ static int sdhci_versal_sampleclk_set_phase(struct clk_hw *hw, int degrees)
 		sdhci_writel(host, regval, SDHCI_ARASAN_ITAPDLY_REGISTER);
 		regval |= SDHCI_ITAPDLY_ENABLE;
 		sdhci_writel(host, regval, SDHCI_ARASAN_ITAPDLY_REGISTER);
+		regval &= ~SDHCI_ARASAN_ITAPDLY_SEL_MASK;
 		regval |= tap_delay;
 		sdhci_writel(host, regval, SDHCI_ARASAN_ITAPDLY_REGISTER);
 		regval &= ~SDHCI_ITAPDLY_CHGWIN;

drivers/mmc/host/sdhci-pci-core.c

@@ -665,6 +665,15 @@ static void sdhci_intel_set_power(struct sdhci_host *host, unsigned char mode,
 	}
 }
 
+static void sdhci_intel_set_uhs_signaling(struct sdhci_host *host,
+					  unsigned int timing)
+{
+	/* Set UHS timing to SDR25 for High Speed mode */
+	if (timing == MMC_TIMING_MMC_HS || timing == MMC_TIMING_SD_HS)
+		timing = MMC_TIMING_UHS_SDR25;
+	sdhci_set_uhs_signaling(host, timing);
+}
+
 #define INTEL_HS400_ES_REG 0x78
 #define INTEL_HS400_ES_BIT BIT(0)
 
@@ -721,7 +730,7 @@ static const struct sdhci_ops sdhci_intel_byt_ops = {
 	.enable_dma		= sdhci_pci_enable_dma,
 	.set_bus_width		= sdhci_set_bus_width,
 	.reset			= sdhci_reset,
-	.set_uhs_signaling	= sdhci_set_uhs_signaling,
+	.set_uhs_signaling	= sdhci_intel_set_uhs_signaling,
 	.hw_reset		= sdhci_pci_hw_reset,
 };
 
@@ -731,7 +740,7 @@ static const struct sdhci_ops sdhci_intel_glk_ops = {
 	.enable_dma		= sdhci_pci_enable_dma,
 	.set_bus_width		= sdhci_set_bus_width,
 	.reset			= sdhci_cqhci_reset,
-	.set_uhs_signaling	= sdhci_set_uhs_signaling,
+	.set_uhs_signaling	= sdhci_intel_set_uhs_signaling,
 	.hw_reset		= sdhci_pci_hw_reset,
 	.irq			= sdhci_cqhci_irq,
 };