Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull arm soc-specific updates from Arnd Bergmann:
 "This is stuff that does not fit well into another category and in
  particular is not related to a particular board.  The largest part in
  here is extending the am33xx support in the omap platform."

Fix up trivial conflicts in arch/arm/mach-{imx/mach-mx35_3ds.c, tegra/Makefile}

* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (74 commits)
  ARM: LPC32xx: Add PWM support
  ARM: LPC32xx: Add PWM clock
  ARM: LPC32xx: Set system serial based on cpu unique id
  ARM: vexpress: Config option for early printk console
  ARM: vexpress: Add Device Tree for V2P-CA15_CA7 core tile
  ARM: vexpress: Convert V2P-CA15 Device Tree to 64 bit addresses
  ARM: vexpress: Add fixed regulator for SMSC
  ARM: vexpress: Add missing SP804 interrupt in motherboard's DTS files
  ARM: vexpress: Initial common clock support
  ARM: SAMSUNG: Introduce Kconfig variable for Samsung custom clk API
  ARM: EXYNOS: Add missing static storage class specifier in pmu.c file
  ARM: EXYNOS: Make combiner_init function static
  ARM: EXYNOS: Update HSOTG PHY clock setting for EXYNOS4X12
  ARM: versatile: Make plat-versatile clock optional
  ARM: vexpress: Check master site in daughterboard's sysctl operations
  ARM: vexpress: remove automatic errata workaround selection
  ARM: LPC32xx: Adjust to pl08x DMA interface changes
  ARM: EXYNOS: Clear SYS_WDTRESET bit to use watchdog reset
  ARM: imx: fix mx51 ehci setup errors
  ARM: imx: make ehci power/oc polarities configurable
  ...

arch/arm/Kconfig

@@ -260,6 +260,7 @@ config ARCH_INTEGRATOR
 	select ICST
 	select GENERIC_CLOCKEVENTS
 	select PLAT_VERSATILE
+	select PLAT_VERSATILE_CLOCK
 	select PLAT_VERSATILE_FPGA_IRQ
 	select NEED_MACH_IO_H
 	select NEED_MACH_MEMORY_H
@@ -277,6 +278,7 @@ config ARCH_REALVIEW
 	select GENERIC_CLOCKEVENTS
 	select ARCH_WANT_OPTIONAL_GPIOLIB
 	select PLAT_VERSATILE
+	select PLAT_VERSATILE_CLOCK
 	select PLAT_VERSATILE_CLCD
 	select ARM_TIMER_SP804
 	select GPIO_PL061 if GPIOLIB
@@ -295,6 +297,7 @@ config ARCH_VERSATILE
 	select ARCH_WANT_OPTIONAL_GPIOLIB
 	select NEED_MACH_IO_H if PCI
 	select PLAT_VERSATILE
+	select PLAT_VERSATILE_CLOCK
 	select PLAT_VERSATILE_CLCD
 	select PLAT_VERSATILE_FPGA_IRQ
 	select ARM_TIMER_SP804
@@ -307,7 +310,7 @@ config ARCH_VEXPRESS
 	select ARM_AMBA
 	select ARM_TIMER_SP804
 	select CLKDEV_LOOKUP
-	select HAVE_MACH_CLKDEV
+	select COMMON_CLK
 	select GENERIC_CLOCKEVENTS
 	select HAVE_CLK
 	select HAVE_PATA_PLATFORM
@@ -315,6 +318,7 @@ config ARCH_VEXPRESS
 	select NO_IOPORT
 	select PLAT_VERSATILE
 	select PLAT_VERSATILE_CLCD
+	select REGULATOR_FIXED_VOLTAGE if REGULATOR
 	help
 	  This enables support for the ARM Ltd Versatile Express boards.
 
@@ -567,6 +571,7 @@ config ARCH_LPC32XX
 	select CLKDEV_LOOKUP
 	select GENERIC_CLOCKEVENTS
 	select USE_OF
+	select HAVE_PWM
 	help
 	  Support for the NXP LPC32XX family of processors
 
@@ -913,7 +918,7 @@ config ARCH_NOMADIK
 	select ARM_AMBA
 	select ARM_VIC
 	select CPU_ARM926T
-	select CLKDEV_LOOKUP
+	select COMMON_CLK
 	select GENERIC_CLOCKEVENTS
 	select PINCTRL
 	select MIGHT_HAVE_CACHE_L2X0
@@ -1022,8 +1027,6 @@ source "arch/arm/mach-kirkwood/Kconfig"
 
 source "arch/arm/mach-ks8695/Kconfig"
 
-source "arch/arm/mach-lpc32xx/Kconfig"
-
 source "arch/arm/mach-msm/Kconfig"
 
 source "arch/arm/mach-mv78xx0/Kconfig"

arch/arm/Kconfig.debug

@@ -310,6 +310,32 @@ choice
 		  The uncompressor code port configuration is now handled
 		  by CONFIG_S3C_LOWLEVEL_UART_PORT.
 
+	config DEBUG_VEXPRESS_UART0_DETECT
+		bool "Autodetect UART0 on Versatile Express Cortex-A core tiles"
+		depends on ARCH_VEXPRESS && CPU_CP15_MMU
+		help
+		  This option enables a simple heuristic which tries to determine
+		  the motherboard's memory map variant (original or RS1) and then
+		  choose the relevant UART0 base address.
+
+		  Note that this will only work with standard A-class core tiles,
+		  and may fail with non-standard SMM or custom software models.
+
+	config DEBUG_VEXPRESS_UART0_CA9
+		bool "Use PL011 UART0 at 0x10009000 (V2P-CA9 core tile)"
+		depends on ARCH_VEXPRESS
+		help
+		  This option selects UART0 at 0x10009000. Except for custom models,
+		  this applies only to the V2P-CA9 tile.
+
+	config DEBUG_VEXPRESS_UART0_RS1
+		bool "Use PL011 UART0 at 0x1c090000 (RS1 complaint tiles)"
+		depends on ARCH_VEXPRESS
+		help
+		  This option selects UART0 at 0x1c090000. This applies to most
+		  of the tiles using the RS1 memory map, including all new A-class
+		  core tiles, FPGA-based SMMs and software models.
+
 	config DEBUG_LL_UART_NONE
 		bool "No low-level debugging UART"
 		help

arch/arm/boot/dts/ea3250.dts

+/*
+ * Embedded Artists LPC3250 board
+ *
+ * Copyright 2012 Roland Stigge <stigge@antcom.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+/include/ "lpc32xx.dtsi"
+
+/ {
+	model = "Embedded Artists LPC3250 board based on NXP LPC3250";
+	compatible = "ea,ea3250", "nxp,lpc3250";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory {
+		device_type = "memory";
+		reg = <0 0x4000000>;
+	};
+
+	ahb {
+		mac: ethernet@31060000 {
+			phy-mode = "rmii";
+			use-iram;
+		};
+
+		/* Here, choose exactly one from: ohci, usbd */
+		ohci@31020000 {
+			transceiver = <&isp1301>;
+			status = "okay";
+		};
+
+/*
+		usbd@31020000 {
+			transceiver = <&isp1301>;
+			status = "okay";
+		};
+*/
+
+		/* 128MB Flash via SLC NAND controller */
+		slc: flash@20020000 {
+			status = "okay";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			nxp,wdr-clks = <14>;
+			nxp,wwidth = <260000000>;
+			nxp,whold = <104000000>;
+			nxp,wsetup = <200000000>;
+			nxp,rdr-clks = <14>;
+			nxp,rwidth = <34666666>;
+			nxp,rhold = <104000000>;
+			nxp,rsetup = <200000000>;
+			nand-on-flash-bbt;
+			gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */
+
+			mtd0@00000000 {
+				label = "ea3250-boot";
+				reg = <0x00000000 0x00080000>;
+				read-only;
+			};
+
+			mtd1@00080000 {
+				label = "ea3250-uboot";
+				reg = <0x00080000 0x000c0000>;
+				read-only;
+			};
+
+			mtd2@00140000 {
+				label = "ea3250-kernel";
+				reg = <0x00140000 0x00400000>;
+			};
+
+			mtd3@00540000 {
+				label = "ea3250-rootfs";
+				reg = <0x00540000 0x07ac0000>;
+			};
+		};
+
+		apb {
+			uart5: serial@40090000 {
+				status = "okay";
+			};
+
+			uart3: serial@40080000 {
+				status = "okay";
+			};
+
+			uart6: serial@40098000 {
+				status = "okay";
+			};
+
+			i2c1: i2c@400A0000 {
+				clock-frequency = <100000>;
+
+				eeprom@50 {
+					compatible = "at,24c256";
+					reg = <0x50>;
+				};
+
+				eeprom@57 {
+					compatible = "at,24c64";
+					reg = <0x57>;
+				};
+
+				uda1380: uda1380@18 {
+					compatible = "nxp,uda1380";
+					reg = <0x18>;
+					power-gpio = <&gpio 0x59 0>;
+					reset-gpio = <&gpio 0x51 0>;
+					dac-clk = "wspll";
+				};
+
+				pca9532: pca9532@60 {
+					compatible = "nxp,pca9532";
+					gpio-controller;
+					#gpio-cells = <2>;
+					reg = <0x60>;
+				};
+			};
+
+			i2c2: i2c@400A8000 {
+				clock-frequency = <100000>;
+			};
+
+			i2cusb: i2c@31020300 {
+				clock-frequency = <100000>;
+
+				isp1301: usb-transceiver@2d {
+					compatible = "nxp,isp1301";
+					reg = <0x2d>;
+				};
+			};
+
+			sd@20098000 {
+				wp-gpios = <&pca9532 5 0>;
+				cd-gpios = <&pca9532 4 0>;
+				cd-inverted;
+				bus-width = <4>;
+				status = "okay";
+			};
+		};
+
+		fab {
+			uart1: serial@40014000 {
+				status = "okay";
+			};
+		};
+	};
+};

arch/arm/boot/dts/lpc32xx.dtsi

@@ -35,13 +35,14 @@ ahb {
 		slc: flash@20020000 {
 			compatible = "nxp,lpc3220-slc";
 			reg = <0x20020000 0x1000>;
-			status = "disable";
+			status = "disabled";
 		};
 
-		mlc: flash@200B0000 {
+		mlc: flash@200a8000 {
 			compatible = "nxp,lpc3220-mlc";
-			reg = <0x200B0000 0x1000>;
-			status = "disable";
+			reg = <0x200a8000 0x11000>;
+			interrupts = <11 0>;
+			status = "disabled";
 		};
 
 		dma@31000000 {
@@ -57,21 +58,21 @@ ohci@31020000 {
 			compatible = "nxp,ohci-nxp", "usb-ohci";
 			reg = <0x31020000 0x300>;
 			interrupts = <0x3b 0>;
-			status = "disable";
+			status = "disabled";
 		};
 
 		usbd@31020000 {
 			compatible = "nxp,lpc3220-udc";
 			reg = <0x31020000 0x300>;
 			interrupts = <0x3d 0>, <0x3e 0>, <0x3c 0>, <0x3a 0>;
-			status = "disable";
+			status = "disabled";
 		};
 
 		clcd@31040000 {
 			compatible = "arm,pl110", "arm,primecell";
 			reg = <0x31040000 0x1000>;
 			interrupts = <0x0e 0>;
-			status = "disable";
+			status = "disabled";
 		};
 
 		mac: ethernet@31060000 {
@@ -114,9 +115,10 @@ i2s0: i2s@20094000 {
 			};
 
 			sd@20098000 {
-				compatible = "arm,pl180", "arm,primecell";
+				compatible = "arm,pl18x", "arm,primecell";
 				reg = <0x20098000 0x1000>;
 				interrupts = <0x0f 0>, <0x0d 0>;
+				status = "disabled";
 			};
 
 			i2s1: i2s@2009C000 {
@@ -124,24 +126,42 @@ i2s1: i2s@2009C000 {
 				reg = <0x2009C000 0x1000>;
 			};
 
+			/* UART5 first since it is the default console, ttyS0 */
+			uart5: serial@40090000 {
+				/* actually, ns16550a w/ 64 byte fifos! */
+				compatible = "nxp,lpc3220-uart";
+				reg = <0x40090000 0x1000>;
+				interrupts = <9 0>;
+				clock-frequency = <13000000>;
+				reg-shift = <2>;
+				status = "disabled";
+			};
+
 			uart3: serial@40080000 {
-				compatible = "nxp,serial";
+				compatible = "nxp,lpc3220-uart";
 				reg = <0x40080000 0x1000>;
+				interrupts = <7 0>;
+				clock-frequency = <13000000>;
+				reg-shift = <2>;
+				status = "disabled";
 			};
 
 			uart4: serial@40088000 {
-				compatible = "nxp,serial";
+				compatible = "nxp,lpc3220-uart";
 				reg = <0x40088000 0x1000>;
-			};
-
-			uart5: serial@40090000 {
-				compatible = "nxp,serial";
-				reg = <0x40090000 0x1000>;
+				interrupts = <8 0>;
+				clock-frequency = <13000000>;
+				reg-shift = <2>;
+				status = "disabled";
 			};
 
 			uart6: serial@40098000 {
-				compatible = "nxp,serial";
+				compatible = "nxp,lpc3220-uart";
 				reg = <0x40098000 0x1000>;
+				interrupts = <10 0>;
+				clock-frequency = <13000000>;
+				reg-shift = <2>;
+				status = "disabled";
 			};
 
 			i2c1: i2c@400A0000 {
@@ -192,18 +212,24 @@ mic: interrupt-controller@40008000 {
 			};
 
 			uart1: serial@40014000 {
-				compatible = "nxp,serial";
+				compatible = "nxp,lpc3220-hsuart";
 				reg = <0x40014000 0x1000>;
+				interrupts = <26 0>;
+				status = "disabled";
 			};
 
 			uart2: serial@40018000 {
-				compatible = "nxp,serial";
+				compatible = "nxp,lpc3220-hsuart";
 				reg = <0x40018000 0x1000>;
+				interrupts = <25 0>;
+				status = "disabled";
 			};
 
-			uart7: serial@4001C000 {
-				compatible = "nxp,serial";
-				reg = <0x4001C000 0x1000>;
+			uart7: serial@4001c000 {
+				compatible = "nxp,lpc3220-hsuart";
+				reg = <0x4001c000 0x1000>;
+				interrupts = <24 0>;
+				status = "disabled";
 			};
 
 			rtc@40024000 {
@@ -235,19 +261,21 @@ adc@40048000 {
 				compatible = "nxp,lpc3220-adc";
 				reg = <0x40048000 0x1000>;
 				interrupts = <0x27 0>;
-				status = "disable";
+				status = "disabled";
 			};
 
 			tsc@40048000 {
 				compatible = "nxp,lpc3220-tsc";
 				reg = <0x40048000 0x1000>;
 				interrupts = <0x27 0>;
-				status = "disable";
+				status = "disabled";
 			};
 
 			key@40050000 {
 				compatible = "nxp,lpc3220-key";
 				reg = <0x40050000 0x1000>;
+				interrupts = <54 0>;
+				status = "disabled";
 			};
 
 		};

arch/arm/boot/dts/phy3250.dts

@@ -54,6 +54,17 @@ slc: flash@20020000 {
 			#address-cells = <1>;
 			#size-cells = <1>;
 
+			nxp,wdr-clks = <14>;
+			nxp,wwidth = <40000000>;
+			nxp,whold = <100000000>;
+			nxp,wsetup = <100000000>;
+			nxp,rdr-clks = <14>;
+			nxp,rwidth = <40000000>;
+			nxp,rhold = <66666666>;
+			nxp,rsetup = <100000000>;
+			nand-on-flash-bbt;
+			gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */
+
 			mtd0@00000000 {
 				label = "phy3250-boot";
 				reg = <0x00000000 0x00064000>;
@@ -83,6 +94,14 @@ mtd4@00604000 {
 		};
 
 		apb {
+			uart5: serial@40090000 {
+				status = "okay";
+			};
+
+			uart3: serial@40080000 {
+				status = "okay";
+			};
+
 			i2c1: i2c@400A0000 {
 				clock-frequency = <100000>;
 
@@ -114,16 +133,58 @@ isp1301: usb-transceiver@2c {
 			};
 
 			ssp0: ssp@20084000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				pl022,num-chipselects = <1>;
+				cs-gpios = <&gpio 3 5 0>;
+
 				eeprom: at25@0 {
+					pl022,hierarchy = <0>;
+					pl022,interface = <0>;
+					pl022,slave-tx-disable = <0>;
+					pl022,com-mode = <0>;
+					pl022,rx-level-trig = <1>;
+					pl022,tx-level-trig = <1>;
+					pl022,ctrl-len = <11>;
+					pl022,wait-state = <0>;
+					pl022,duplex = <0>;
+
+					at25,byte-len = <0x8000>;
+					at25,addr-mode = <2>;
+					at25,page-size = <64>;
+
 					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <5000000>;
 				};
 			};
+
+			sd@20098000 {
+				wp-gpios = <&gpio 3 0 0>;
+				cd-gpios = <&gpio 3 1 0>;
+				cd-inverted;
+				bus-width = <4>;
+				status = "okay";
+			};
 		};
 
 		fab {
+			uart2: serial@40018000 {
+				status = "okay";
+			};
+
 			tsc@40048000 {
 				status = "okay";
 			};
+
+			key@40050000 {
+				status = "okay";
+				keypad,num-rows = <1>;
+				keypad,num-columns = <1>;
+				nxp,debounce-delay-ms = <3>;
+				nxp,scan-delay-ms = <34>;
+				linux,keymap = <0x00000002>;
+			};
 		};
 	};
 

arch/arm/boot/dts/vexpress-v2m-rs1.dtsi

@@ -55,6 +55,8 @@ ethernet@2,02000000 {
 			reg-io-width = <4>;
 			smsc,irq-active-high;
 			smsc,irq-push-pull;
+			vdd33a-supply = <&v2m_fixed_3v3>;
+			vddvario-supply = <&v2m_fixed_3v3>;
 		};
 
 		usb@2,03000000 {
@@ -157,6 +159,7 @@ v2m_timer01: timer@110000 {
 			v2m_timer23: timer@120000 {
 				compatible = "arm,sp804", "arm,primecell";
 				reg = <0x120000 0x1000>;
+				interrupts = <3>;
 			};
 
 			/* DVI I2C bus */
@@ -197,5 +200,13 @@ clcd@1f0000 {
 				interrupts = <14>;
 			};
 		};
+
+		v2m_fixed_3v3: fixedregulator@0 {
+			compatible = "regulator-fixed";
+			regulator-name = "3V3";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
 	};
 };

arch/arm/boot/dts/vexpress-v2m.dtsi

@@ -54,6 +54,8 @@ ethernet@3,02000000 {
 			reg-io-width = <4>;
 			smsc,irq-active-high;
 			smsc,irq-push-pull;
+			vdd33a-supply = <&v2m_fixed_3v3>;
+			vddvario-supply = <&v2m_fixed_3v3>;
 		};
 
 		usb@3,03000000 {
@@ -156,6 +158,7 @@ v2m_timer01: timer@11000 {
 			v2m_timer23: timer@12000 {
 				compatible = "arm,sp804", "arm,primecell";
 				reg = <0x12000 0x1000>;
+				interrupts = <3>;
 			};
 
 			/* DVI I2C bus */
@@ -196,5 +199,13 @@ clcd@1f000 {
 				interrupts = <14>;
 			};
 		};
+
+		v2m_fixed_3v3: fixedregulator@0 {
+			compatible = "regulator-fixed";
+			regulator-name = "3V3";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
 	};
 };

arch/arm/boot/dts/vexpress-v2p-ca15-tc1.dts

@@ -14,8 +14,8 @@ / {
 	arm,hbi = <0x237>;
 	compatible = "arm,vexpress,v2p-ca15,tc1", "arm,vexpress,v2p-ca15", "arm,vexpress";
 	interrupt-parent = <&gic>;
-	#address-cells = <1>;
-	#size-cells = <1>;
+	#address-cells = <2>;
+	#size-cells = <2>;
 
 	chosen { };
 
@@ -47,23 +47,23 @@ cpu@1 {
 
 	memory@80000000 {
 		device_type = "memory";
-		reg = <0x80000000 0x40000000>;
+		reg = <0 0x80000000 0 0x40000000>;
 	};
 
 	hdlcd@2b000000 {
 		compatible = "arm,hdlcd";
-		reg = <0x2b000000 0x1000>;
+		reg = <0 0x2b000000 0 0x1000>;
 		interrupts = <0 85 4>;
 	};
 
 	memory-controller@2b0a0000 {
 		compatible = "arm,pl341", "arm,primecell";
-		reg = <0x2b0a0000 0x1000>;
+		reg = <0 0x2b0a0000 0 0x1000>;
 	};
 
 	wdt@2b060000 {
 		compatible = "arm,sp805", "arm,primecell";
-		reg = <0x2b060000 0x1000>;
+		reg = <0 0x2b060000 0 0x1000>;
 		interrupts = <98>;
 	};
 
@@ -72,23 +72,23 @@ gic: interrupt-controller@2c001000 {
 		#interrupt-cells = <3>;
 		#address-cells = <0>;
 		interrupt-controller;
-		reg = <0x2c001000 0x1000>,
-		      <0x2c002000 0x1000>,
-		      <0x2c004000 0x2000>,
-		      <0x2c006000 0x2000>;
+		reg = <0 0x2c001000 0 0x1000>,
+		      <0 0x2c002000 0 0x1000>,
+		      <0 0x2c004000 0 0x2000>,
+		      <0 0x2c006000 0 0x2000>;
 		interrupts = <1 9 0xf04>;
 	};
 
 	memory-controller@7ffd0000 {
 		compatible = "arm,pl354", "arm,primecell";
-		reg = <0x7ffd0000 0x1000>;
+		reg = <0 0x7ffd0000 0 0x1000>;
 		interrupts = <0 86 4>,
 			     <0 87 4>;
 	};
 
 	dma@7ffb0000 {
 		compatible = "arm,pl330", "arm,primecell";
-		reg = <0x7ffb0000 0x1000>;
+		reg = <0 0x7ffb0000 0 0x1000>;
 		interrupts = <0 92 4>,
 			     <0 88 4>,
 			     <0 89 4>,
@@ -111,12 +111,12 @@ pmu {
 	};
 
 	motherboard {
-		ranges = <0 0 0x08000000 0x04000000>,
-			 <1 0 0x14000000 0x04000000>,
-			 <2 0 0x18000000 0x04000000>,
-			 <3 0 0x1c000000 0x04000000>,
-			 <4 0 0x0c000000 0x04000000>,
-			 <5 0 0x10000000 0x04000000>;
+		ranges = <0 0 0 0x08000000 0x04000000>,
+			 <1 0 0 0x14000000 0x04000000>,
+			 <2 0 0 0x18000000 0x04000000>,
+			 <3 0 0 0x1c000000 0x04000000>,
+			 <4 0 0 0x0c000000 0x04000000>,
+			 <5 0 0 0x10000000 0x04000000>;
 
 		interrupt-map-mask = <0 0 63>;
 		interrupt-map = <0 0  0 &gic 0  0 4>,

arch/arm/boot/dts/vexpress-v2p-ca15_a7.dts

+/*
+ * ARM Ltd. Versatile Express
+ *
+ * CoreTile Express A15x2 A7x3
+ * Cortex-A15_A7 MPCore (V2P-CA15_A7)
+ *
+ * HBI-0249A
+ */
+
+/dts-v1/;
+
+/ {
+	model = "V2P-CA15_CA7";
+	arm,hbi = <0x249>;
+	compatible = "arm,vexpress,v2p-ca15_a7", "arm,vexpress";
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	chosen { };
+
+	aliases {
+		serial0 = &v2m_serial0;
+		serial1 = &v2m_serial1;
+		serial2 = &v2m_serial2;
+		serial3 = &v2m_serial3;
+		i2c0 = &v2m_i2c_dvi;
+		i2c1 = &v2m_i2c_pcie;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a15";
+			reg = <0>;
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a15";
+			reg = <1>;
+		};
+
+/* A7s disabled till big.LITTLE patches are available...
+		cpu2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x100>;
+		};
+
+		cpu3: cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x101>;
+		};
+
+		cpu4: cpu@4 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x102>;
+		};
+*/
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0 0x80000000 0 0x40000000>;
+	};
+
+	wdt@2a490000 {
+		compatible = "arm,sp805", "arm,primecell";
+		reg = <0 0x2a490000 0 0x1000>;
+		interrupts = <98>;
+	};
+
+	hdlcd@2b000000 {
+		compatible = "arm,hdlcd";
+		reg = <0 0x2b000000 0 0x1000>;
+		interrupts = <0 85 4>;
+	};
+
+	memory-controller@2b0a0000 {
+		compatible = "arm,pl341", "arm,primecell";
+		reg = <0 0x2b0a0000 0 0x1000>;
+	};
+
+	gic: interrupt-controller@2c001000 {
+		compatible = "arm,cortex-a15-gic", "arm,cortex-a9-gic";
+		#interrupt-cells = <3>;
+		#address-cells = <0>;
+		interrupt-controller;
+		reg = <0 0x2c001000 0 0x1000>,
+		      <0 0x2c002000 0 0x1000>,
+		      <0 0x2c004000 0 0x2000>,
+		      <0 0x2c006000 0 0x2000>;
+		interrupts = <1 9 0xf04>;
+	};
+
+	memory-controller@7ffd0000 {
+		compatible = "arm,pl354", "arm,primecell";
+		reg = <0 0x7ffd0000 0 0x1000>;
+		interrupts = <0 86 4>,
+			     <0 87 4>;
+	};
+
+	dma@7ff00000 {
+		compatible = "arm,pl330", "arm,primecell";
+		reg = <0 0x7ff00000 0 0x1000>;
+		interrupts = <0 92 4>,
+			     <0 88 4>,
+			     <0 89 4>,
+			     <0 90 4>,
+			     <0 91 4>;
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <1 13 0xf08>,
+			     <1 14 0xf08>,
+			     <1 11 0xf08>,
+			     <1 10 0xf08>;
+	};
+
+	pmu {
+		compatible = "arm,cortex-a15-pmu", "arm,cortex-a9-pmu";
+		interrupts = <0 68 4>,
+			     <0 69 4>;
+	};
+
+	motherboard {
+		ranges = <0 0 0 0x08000000 0x04000000>,
+			 <1 0 0 0x14000000 0x04000000>,
+			 <2 0 0 0x18000000 0x04000000>,
+			 <3 0 0 0x1c000000 0x04000000>,
+			 <4 0 0 0x0c000000 0x04000000>,
+			 <5 0 0 0x10000000 0x04000000>;
+
+		interrupt-map-mask = <0 0 63>;
+		interrupt-map = <0 0  0 &gic 0  0 4>,
+				<0 0  1 &gic 0  1 4>,
+				<0 0  2 &gic 0  2 4>,
+				<0 0  3 &gic 0  3 4>,
+				<0 0  4 &gic 0  4 4>,
+				<0 0  5 &gic 0  5 4>,
+				<0 0  6 &gic 0  6 4>,
+				<0 0  7 &gic 0  7 4>,
+				<0 0  8 &gic 0  8 4>,
+				<0 0  9 &gic 0  9 4>,
+				<0 0 10 &gic 0 10 4>,
+				<0 0 11 &gic 0 11 4>,
+				<0 0 12 &gic 0 12 4>,
+				<0 0 13 &gic 0 13 4>,
+				<0 0 14 &gic 0 14 4>,
+				<0 0 15 &gic 0 15 4>,
+				<0 0 16 &gic 0 16 4>,
+				<0 0 17 &gic 0 17 4>,
+				<0 0 18 &gic 0 18 4>,
+				<0 0 19 &gic 0 19 4>,
+				<0 0 20 &gic 0 20 4>,
+				<0 0 21 &gic 0 21 4>,
+				<0 0 22 &gic 0 22 4>,
+				<0 0 23 &gic 0 23 4>,
+				<0 0 24 &gic 0 24 4>,
+				<0 0 25 &gic 0 25 4>,
+				<0 0 26 &gic 0 26 4>,
+				<0 0 27 &gic 0 27 4>,
+				<0 0 28 &gic 0 28 4>,
+				<0 0 29 &gic 0 29 4>,
+				<0 0 30 &gic 0 30 4>,
+				<0 0 31 &gic 0 31 4>,
+				<0 0 32 &gic 0 32 4>,
+				<0 0 33 &gic 0 33 4>,
+				<0 0 34 &gic 0 34 4>,
+				<0 0 35 &gic 0 35 4>,
+				<0 0 36 &gic 0 36 4>,
+				<0 0 37 &gic 0 37 4>,
+				<0 0 38 &gic 0 38 4>,
+				<0 0 39 &gic 0 39 4>,
+				<0 0 40 &gic 0 40 4>,
+				<0 0 41 &gic 0 41 4>,
+				<0 0 42 &gic 0 42 4>;
+	};
+};
+
+/include/ "vexpress-v2m-rs1.dtsi"

arch/arm/configs/lpc32xx_defconfig

 CONFIG_EXPERIMENTAL=y
 CONFIG_SYSVIPC=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
 CONFIG_IKCONFIG=y
 CONFIG_IKCONFIG_PROC=y
 CONFIG_LOG_BUF_SHIFT=16
@@ -16,8 +18,6 @@ CONFIG_MODULE_UNLOAD=y
 # CONFIG_BLK_DEV_BSG is not set
 CONFIG_PARTITION_ADVANCED=y
 CONFIG_ARCH_LPC32XX=y
-CONFIG_NO_HZ=y
-CONFIG_HIGH_RES_TIMERS=y
 CONFIG_PREEMPT=y
 CONFIG_AEABI=y
 CONFIG_ZBOOT_ROM_TEXT=0x0
@@ -52,13 +52,17 @@ CONFIG_MTD=y
 CONFIG_MTD_CMDLINE_PARTS=y
 CONFIG_MTD_CHAR=y
 CONFIG_MTD_BLOCK=y
+CONFIG_MTD_M25P80=y
 CONFIG_MTD_NAND=y
 CONFIG_MTD_NAND_MUSEUM_IDS=y
+CONFIG_MTD_NAND_SLC_LPC32XX=y
+CONFIG_MTD_NAND_MLC_LPC32XX=y
 CONFIG_BLK_DEV_LOOP=y
 CONFIG_BLK_DEV_CRYPTOLOOP=y
 CONFIG_BLK_DEV_RAM=y
 CONFIG_BLK_DEV_RAM_COUNT=1
 CONFIG_BLK_DEV_RAM_SIZE=16384
+CONFIG_EEPROM_AT24=y
 CONFIG_EEPROM_AT25=y
 CONFIG_SCSI=y
 CONFIG_BLK_DEV_SD=y
@@ -79,16 +83,22 @@ CONFIG_LPC_ENET=y
 # CONFIG_NET_VENDOR_STMICRO is not set
 CONFIG_SMSC_PHY=y
 # CONFIG_WLAN is not set
+CONFIG_INPUT_MATRIXKMAP=y
 # CONFIG_INPUT_MOUSEDEV_PSAUX is not set
 CONFIG_INPUT_MOUSEDEV_SCREEN_X=240
 CONFIG_INPUT_MOUSEDEV_SCREEN_Y=320
 CONFIG_INPUT_EVDEV=y
+# CONFIG_KEYBOARD_ATKBD is not set
+CONFIG_KEYBOARD_LPC32XX=y
 # CONFIG_INPUT_MOUSE is not set
 CONFIG_INPUT_TOUCHSCREEN=y
 CONFIG_TOUCHSCREEN_LPC32XX=y
+CONFIG_SERIO_LIBPS2=y
 # CONFIG_LEGACY_PTYS is not set
 CONFIG_SERIAL_8250=y
 CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_HS_LPC32XX=y
+CONFIG_SERIAL_OF_PLATFORM=y
 # CONFIG_HW_RANDOM is not set
 CONFIG_I2C=y
 CONFIG_I2C_CHARDEV=y
@@ -96,7 +106,8 @@ CONFIG_I2C_PNX=y
 CONFIG_SPI=y
 CONFIG_SPI_PL022=y
 CONFIG_GPIO_SYSFS=y
-# CONFIG_HWMON is not set
+CONFIG_SENSORS_DS620=y
+CONFIG_SENSORS_MAX6639=y
 CONFIG_WATCHDOG=y
 CONFIG_PNX4008_WATCHDOG=y
 CONFIG_FB=y
@@ -133,6 +144,8 @@ CONFIG_MMC=y
 CONFIG_MMC_ARMMMCI=y
 CONFIG_NEW_LEDS=y
 CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_PCA9532=y
+CONFIG_LEDS_PCA9532_GPIO=y
 CONFIG_LEDS_GPIO=y
 CONFIG_LEDS_TRIGGERS=y
 CONFIG_LEDS_TRIGGER_TIMER=y
@@ -146,10 +159,10 @@ CONFIG_RTC_DRV_DS1374=y
 CONFIG_RTC_DRV_PCF8563=y
 CONFIG_RTC_DRV_LPC32XX=y
 CONFIG_DMADEVICES=y
-CONFIG_AMBA_PL08X=y
 CONFIG_STAGING=y
-CONFIG_IIO=y
 CONFIG_LPC32XX_ADC=y
+CONFIG_MAX517=y
+CONFIG_IIO=y
 CONFIG_EXT2_FS=y
 CONFIG_AUTOFS4_FS=y
 CONFIG_MSDOS_FS=y
@@ -159,7 +172,6 @@ CONFIG_JFFS2_FS=y
 CONFIG_JFFS2_FS_WBUF_VERIFY=y
 CONFIG_CRAMFS=y
 CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
 CONFIG_ROOT_NFS=y
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ASCII=y

arch/arm/mach-davinci/Kconfig

@@ -4,6 +4,7 @@ config AINTC
 	bool
 
 config CP_INTC
+	select IRQ_DOMAIN
 	bool
 
 config ARCH_DAVINCI_DMx

arch/arm/mach-davinci/Makefile

@@ -39,3 +39,4 @@ obj-$(CONFIG_MACH_OMAPL138_HAWKBOARD)	+= board-omapl138-hawk.o
 obj-$(CONFIG_CPU_FREQ)			+= cpufreq.o
 obj-$(CONFIG_CPU_IDLE)			+= cpuidle.o
 obj-$(CONFIG_SUSPEND)			+= pm.o sleep.o
+obj-$(CONFIG_HAVE_CLK)			+= pm_domain.o

arch/arm/mach-davinci/cp_intc.c

@@ -9,8 +9,10 @@
  * kind, whether express or implied.
  */
 
+#include <linux/export.h>
 #include <linux/init.h>
 #include <linux/irq.h>
+#include <linux/irqdomain.h>
 #include <linux/io.h>
 
 #include <mach/common.h>
@@ -28,7 +30,7 @@ static inline void cp_intc_write(unsigned long value, unsigned offset)
 
 static void cp_intc_ack_irq(struct irq_data *d)
 {
-	cp_intc_write(d->irq, CP_INTC_SYS_STAT_IDX_CLR);
+	cp_intc_write(d->hwirq, CP_INTC_SYS_STAT_IDX_CLR);
 }
 
 /* Disable interrupt */
@@ -36,20 +38,20 @@ static void cp_intc_mask_irq(struct irq_data *d)
 {
 	/* XXX don't know why we need to disable nIRQ here... */
 	cp_intc_write(1, CP_INTC_HOST_ENABLE_IDX_CLR);
-	cp_intc_write(d->irq, CP_INTC_SYS_ENABLE_IDX_CLR);
+	cp_intc_write(d->hwirq, CP_INTC_SYS_ENABLE_IDX_CLR);
 	cp_intc_write(1, CP_INTC_HOST_ENABLE_IDX_SET);
 }
 
 /* Enable interrupt */
 static void cp_intc_unmask_irq(struct irq_data *d)
 {
-	cp_intc_write(d->irq, CP_INTC_SYS_ENABLE_IDX_SET);
+	cp_intc_write(d->hwirq, CP_INTC_SYS_ENABLE_IDX_SET);
 }
 
 static int cp_intc_set_irq_type(struct irq_data *d, unsigned int flow_type)
 {
-	unsigned reg		= BIT_WORD(d->irq);
-	unsigned mask		= BIT_MASK(d->irq);
+	unsigned reg		= BIT_WORD(d->hwirq);
+	unsigned mask		= BIT_MASK(d->hwirq);
 	unsigned polarity	= cp_intc_read(CP_INTC_SYS_POLARITY(reg));
 	unsigned type		= cp_intc_read(CP_INTC_SYS_TYPE(reg));
 
@@ -99,18 +101,36 @@ static struct irq_chip cp_intc_irq_chip = {
 	.irq_set_wake	= cp_intc_set_wake,
 };
 
-void __init cp_intc_init(void)
+static struct irq_domain *cp_intc_domain;
+
+static int cp_intc_host_map(struct irq_domain *h, unsigned int virq,
+			  irq_hw_number_t hw)
+{
+	pr_debug("cp_intc_host_map(%d, 0x%lx)\n", virq, hw);
+
+	irq_set_chip(virq, &cp_intc_irq_chip);
+	set_irq_flags(virq, IRQF_VALID | IRQF_PROBE);
+	irq_set_handler(virq, handle_edge_irq);
+	return 0;
+}
+
+static const struct irq_domain_ops cp_intc_host_ops = {
+	.map = cp_intc_host_map,
+	.xlate = irq_domain_xlate_onetwocell,
+};
+
+int __init __cp_intc_init(struct device_node *node)
 {
-	unsigned long num_irq	= davinci_soc_info.intc_irq_num;
+	u32 num_irq		= davinci_soc_info.intc_irq_num;
 	u8 *irq_prio		= davinci_soc_info.intc_irq_prios;
 	u32 *host_map		= davinci_soc_info.intc_host_map;
 	unsigned num_reg	= BITS_TO_LONGS(num_irq);
-	int i;
+	int i, irq_base;
 
 	davinci_intc_type = DAVINCI_INTC_TYPE_CP_INTC;
 	davinci_intc_base = ioremap(davinci_soc_info.intc_base, SZ_8K);
 	if (WARN_ON(!davinci_intc_base))
-		return;
+		return -EINVAL;
 
 	cp_intc_write(0, CP_INTC_GLOBAL_ENABLE);
 
@@ -165,13 +185,28 @@ void __init cp_intc_init(void)
 		for (i = 0; host_map[i] != -1; i++)
 			cp_intc_write(host_map[i], CP_INTC_HOST_MAP(i));
 
-	/* Set up genirq dispatching for cp_intc */
-	for (i = 0; i < num_irq; i++) {
-		irq_set_chip(i, &cp_intc_irq_chip);
-		set_irq_flags(i, IRQF_VALID | IRQF_PROBE);
-		irq_set_handler(i, handle_edge_irq);
+	irq_base = irq_alloc_descs(-1, 0, num_irq, 0);
+	if (irq_base < 0) {
+		pr_warn("Couldn't allocate IRQ numbers\n");
+		irq_base = 0;
+	}
+
+	/* create a legacy host */
+	cp_intc_domain = irq_domain_add_legacy(node, num_irq,
+					irq_base, 0, &cp_intc_host_ops, NULL);
+
+	if (!cp_intc_domain) {
+		pr_err("cp_intc: failed to allocate irq host!\n");
+		return -EINVAL;
 	}
 
 	/* Enable global interrupt */
 	cp_intc_write(1, CP_INTC_GLOBAL_ENABLE);
+
+	return 0;
+}
+
+void __init cp_intc_init(void)
+{
+	__cp_intc_init(NULL);
 }

arch/arm/mach-davinci/pm_domain.c

+/*
+ * Runtime PM support code for DaVinci
+ *
+ * Author: Kevin Hilman
+ *
+ * Copyright (C) 2012 Texas Instruments, Inc.
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+#include <linux/init.h>
+#include <linux/pm_runtime.h>
+#include <linux/pm_clock.h>
+#include <linux/platform_device.h>
+
+#ifdef CONFIG_PM_RUNTIME
+static int davinci_pm_runtime_suspend(struct device *dev)
+{
+	int ret;
+
+	dev_dbg(dev, "%s\n", __func__);
+
+	ret = pm_generic_runtime_suspend(dev);
+	if (ret)
+		return ret;
+
+	ret = pm_clk_suspend(dev);
+	if (ret) {
+		pm_generic_runtime_resume(dev);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int davinci_pm_runtime_resume(struct device *dev)
+{
+	dev_dbg(dev, "%s\n", __func__);
+
+	pm_clk_resume(dev);
+	return pm_generic_runtime_resume(dev);
+}
+#endif
+
+static struct dev_pm_domain davinci_pm_domain = {
+	.ops = {
+		SET_RUNTIME_PM_OPS(davinci_pm_runtime_suspend,
+				   davinci_pm_runtime_resume, NULL)
+		USE_PLATFORM_PM_SLEEP_OPS
+	},
+};
+
+static struct pm_clk_notifier_block platform_bus_notifier = {
+	.pm_domain = &davinci_pm_domain,
+};
+
+static int __init davinci_pm_runtime_init(void)
+{
+	pm_clk_add_notifier(&platform_bus_type, &platform_bus_notifier);
+
+	return 0;
+}
+core_initcall(davinci_pm_runtime_init);

arch/arm/mach-ep93xx/core.c

@@ -797,6 +797,102 @@ static struct platform_device ep93xx_wdt_device = {
 	.resource	= ep93xx_wdt_resources,
 };
 
+/*************************************************************************
+ * EP93xx IDE
+ *************************************************************************/
+static struct resource ep93xx_ide_resources[] = {
+	DEFINE_RES_MEM(EP93XX_IDE_PHYS_BASE, 0x38),
+	DEFINE_RES_IRQ(IRQ_EP93XX_EXT3),
+};
+
+static struct platform_device ep93xx_ide_device = {
+	.name		= "ep93xx-ide",
+	.id		= -1,
+	.dev		= {
+		.dma_mask		= &ep93xx_ide_device.dev.coherent_dma_mask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+	},
+	.num_resources	= ARRAY_SIZE(ep93xx_ide_resources),
+	.resource	= ep93xx_ide_resources,
+};
+
+void __init ep93xx_register_ide(void)
+{
+	platform_device_register(&ep93xx_ide_device);
+}
+
+int ep93xx_ide_acquire_gpio(struct platform_device *pdev)
+{
+	int err;
+	int i;
+
+	err = gpio_request(EP93XX_GPIO_LINE_EGPIO2, dev_name(&pdev->dev));
+	if (err)
+		return err;
+	err = gpio_request(EP93XX_GPIO_LINE_EGPIO15, dev_name(&pdev->dev));
+	if (err)
+		goto fail_egpio15;
+	for (i = 2; i < 8; i++) {
+		err = gpio_request(EP93XX_GPIO_LINE_E(i), dev_name(&pdev->dev));
+		if (err)
+			goto fail_gpio_e;
+	}
+	for (i = 4; i < 8; i++) {
+		err = gpio_request(EP93XX_GPIO_LINE_G(i), dev_name(&pdev->dev));
+		if (err)
+			goto fail_gpio_g;
+	}
+	for (i = 0; i < 8; i++) {
+		err = gpio_request(EP93XX_GPIO_LINE_H(i), dev_name(&pdev->dev));
+		if (err)
+			goto fail_gpio_h;
+	}
+
+	/* GPIO ports E[7:2], G[7:4] and H used by IDE */
+	ep93xx_devcfg_clear_bits(EP93XX_SYSCON_DEVCFG_EONIDE |
+				 EP93XX_SYSCON_DEVCFG_GONIDE |
+				 EP93XX_SYSCON_DEVCFG_HONIDE);
+	return 0;
+
+fail_gpio_h:
+	for (--i; i >= 0; --i)
+		gpio_free(EP93XX_GPIO_LINE_H(i));
+	i = 8;
+fail_gpio_g:
+	for (--i; i >= 4; --i)
+		gpio_free(EP93XX_GPIO_LINE_G(i));
+	i = 8;
+fail_gpio_e:
+	for (--i; i >= 2; --i)
+		gpio_free(EP93XX_GPIO_LINE_E(i));
+	gpio_free(EP93XX_GPIO_LINE_EGPIO15);
+fail_egpio15:
+	gpio_free(EP93XX_GPIO_LINE_EGPIO2);
+	return err;
+}
+EXPORT_SYMBOL(ep93xx_ide_acquire_gpio);
+
+void ep93xx_ide_release_gpio(struct platform_device *pdev)
+{
+	int i;
+
+	for (i = 2; i < 8; i++)
+		gpio_free(EP93XX_GPIO_LINE_E(i));
+	for (i = 4; i < 8; i++)
+		gpio_free(EP93XX_GPIO_LINE_G(i));
+	for (i = 0; i < 8; i++)
+		gpio_free(EP93XX_GPIO_LINE_H(i));
+	gpio_free(EP93XX_GPIO_LINE_EGPIO15);
+	gpio_free(EP93XX_GPIO_LINE_EGPIO2);
+
+
+	/* GPIO ports E[7:2], G[7:4] and H used by GPIO */
+	ep93xx_devcfg_set_bits(EP93XX_SYSCON_DEVCFG_EONIDE |
+			       EP93XX_SYSCON_DEVCFG_GONIDE |
+			       EP93XX_SYSCON_DEVCFG_HONIDE);
+}
+EXPORT_SYMBOL(ep93xx_ide_release_gpio);
+
 void __init ep93xx_init_devices(void)
 {
 	/* Disallow access to MaverickCrunch initially */

arch/arm/mach-ep93xx/edb93xx.c

@@ -233,6 +233,29 @@ static void __init edb93xx_register_fb(void)
 }
 
 
+/*************************************************************************
+ * EDB93xx IDE
+ *************************************************************************/
+static int __init edb93xx_has_ide(void)
+{
+	/*
+	 * Although EDB9312 and EDB9315 do have IDE capability, they have
+	 * INTRQ line wired as pull-up, which makes using IDE interface
+	 * problematic.
+	 */
+	return machine_is_edb9312() || machine_is_edb9315() ||
+	       machine_is_edb9315a();
+}
+
+static void __init edb93xx_register_ide(void)
+{
+	if (!edb93xx_has_ide())
+		return;
+
+	ep93xx_register_ide();
+}
+
+
 static void __init edb93xx_init_machine(void)
 {
 	ep93xx_init_devices();
@@ -243,6 +266,7 @@ static void __init edb93xx_init_machine(void)
 	edb93xx_register_i2s();
 	edb93xx_register_pwm();
 	edb93xx_register_fb();
+	edb93xx_register_ide();
 }
 
 

arch/arm/mach-ep93xx/include/mach/platform.h

@@ -48,6 +48,9 @@ void ep93xx_register_i2s(void);
 int ep93xx_i2s_acquire(void);
 void ep93xx_i2s_release(void);
 void ep93xx_register_ac97(void);
+void ep93xx_register_ide(void);
+int ep93xx_ide_acquire_gpio(struct platform_device *pdev);
+void ep93xx_ide_release_gpio(struct platform_device *pdev);
 
 void ep93xx_init_devices(void);
 extern struct sys_timer ep93xx_timer;

arch/arm/mach-ep93xx/soc.h

@@ -69,6 +69,7 @@
 
 #define EP93XX_BOOT_ROM_BASE		EP93XX_AHB_IOMEM(0x00090000)
 
+#define EP93XX_IDE_PHYS_BASE		EP93XX_AHB_PHYS(0x000a0000)
 #define EP93XX_IDE_BASE			EP93XX_AHB_IOMEM(0x000a0000)
 
 #define EP93XX_VIC1_BASE		EP93XX_AHB_IOMEM(0x000b0000)

arch/arm/mach-exynos/common.c

@@ -540,7 +540,8 @@ static struct irq_domain_ops combiner_irq_domain_ops = {
 	.map	= combiner_irq_domain_map,
 };
 
-void __init combiner_init(void __iomem *combiner_base, struct device_node *np)
+static void __init combiner_init(void __iomem *combiner_base,
+				 struct device_node *np)
 {
 	int i, irq, irq_base;
 	unsigned int max_nr, nr_irq;

arch/arm/mach-exynos/include/mach/regs-pmu.h

@@ -232,6 +232,11 @@
 
 #define EXYNOS5_USB_CFG						S5P_PMUREG(0x0230)
 
+#define EXYNOS5_AUTO_WDTRESET_DISABLE				S5P_PMUREG(0x0408)
+#define EXYNOS5_MASK_WDTRESET_REQUEST				S5P_PMUREG(0x040C)
+
+#define EXYNOS5_SYS_WDTRESET					(1 << 20)
+
 #define EXYNOS5_ARM_CORE0_SYS_PWR_REG				S5P_PMUREG(0x1000)
 #define EXYNOS5_DIS_IRQ_ARM_CORE0_LOCAL_SYS_PWR_REG		S5P_PMUREG(0x1004)
 #define EXYNOS5_DIS_IRQ_ARM_CORE0_CENTRAL_SYS_PWR_REG		S5P_PMUREG(0x1008)

arch/arm/mach-exynos/include/mach/regs-usb-phy.h

@@ -35,11 +35,21 @@
 #define PHY1_COMMON_ON_N		(1 << 7)
 #define PHY0_COMMON_ON_N		(1 << 4)
 #define PHY0_ID_PULLUP			(1 << 2)
-#define CLKSEL_MASK			(0x3 << 0)
-#define CLKSEL_SHIFT			(0)
-#define CLKSEL_48M			(0x0 << 0)
-#define CLKSEL_12M			(0x2 << 0)
-#define CLKSEL_24M			(0x3 << 0)
+
+#define EXYNOS4_CLKSEL_SHIFT		(0)
+
+#define EXYNOS4210_CLKSEL_MASK		(0x3 << 0)
+#define EXYNOS4210_CLKSEL_48M		(0x0 << 0)
+#define EXYNOS4210_CLKSEL_12M		(0x2 << 0)
+#define EXYNOS4210_CLKSEL_24M		(0x3 << 0)
+
+#define EXYNOS4X12_CLKSEL_MASK		(0x7 << 0)
+#define EXYNOS4X12_CLKSEL_9600K		(0x0 << 0)
+#define EXYNOS4X12_CLKSEL_10M		(0x1 << 0)
+#define EXYNOS4X12_CLKSEL_12M		(0x2 << 0)
+#define EXYNOS4X12_CLKSEL_19200K	(0x3 << 0)
+#define EXYNOS4X12_CLKSEL_20M		(0x4 << 0)
+#define EXYNOS4X12_CLKSEL_24M		(0x5 << 0)
 
 #define EXYNOS4_RSTCON			EXYNOS4_HSOTG_PHYREG(0x08)
 #define HOST_LINK_PORT_SWRST_MASK	(0xf << 6)

arch/arm/mach-exynos/pmu.c

@@ -315,7 +315,7 @@ static struct exynos_pmu_conf exynos5250_pmu_config[] = {
 	{ PMU_TABLE_END,},
 };
 
-void __iomem *exynos5_list_both_cnt_feed[] = {
+static void __iomem *exynos5_list_both_cnt_feed[] = {
 	EXYNOS5_ARM_CORE0_OPTION,
 	EXYNOS5_ARM_CORE1_OPTION,
 	EXYNOS5_ARM_COMMON_OPTION,
@@ -329,7 +329,7 @@ void __iomem *exynos5_list_both_cnt_feed[] = {
 	EXYNOS5_TOP_PWR_SYSMEM_OPTION,
 };
 
-void __iomem *exynos5_list_diable_wfi_wfe[] = {
+static void __iomem *exynos5_list_diable_wfi_wfe[] = {
 	EXYNOS5_ARM_CORE1_OPTION,
 	EXYNOS5_FSYS_ARM_OPTION,
 	EXYNOS5_ISP_ARM_OPTION,
@@ -390,6 +390,8 @@ void exynos_sys_powerdown_conf(enum sys_powerdown mode)
 
 static int __init exynos_pmu_init(void)
 {
+	unsigned int value;
+
 	exynos_pmu_config = exynos4210_pmu_config;
 
 	if (soc_is_exynos4210()) {
@@ -399,6 +401,18 @@ static int __init exynos_pmu_init(void)
 		exynos_pmu_config = exynos4x12_pmu_config;
 		pr_info("EXYNOS4x12 PMU Initialize\n");
 	} else if (soc_is_exynos5250()) {
+		/*
+		 * When SYS_WDTRESET is set, watchdog timer reset request
+		 * is ignored by power management unit.
+		 */
+		value = __raw_readl(EXYNOS5_AUTO_WDTRESET_DISABLE);
+		value &= ~EXYNOS5_SYS_WDTRESET;
+		__raw_writel(value, EXYNOS5_AUTO_WDTRESET_DISABLE);
+
+		value = __raw_readl(EXYNOS5_MASK_WDTRESET_REQUEST);
+		value &= ~EXYNOS5_SYS_WDTRESET;
+		__raw_writel(value, EXYNOS5_MASK_WDTRESET_REQUEST);
+
 		exynos_pmu_config = exynos5250_pmu_config;
 		pr_info("EXYNOS5250 PMU Initialize\n");
 	} else {

arch/arm/mach-exynos/setup-usb-phy.c

@@ -31,27 +31,55 @@ static void exynos4210_usb_phy_clkset(struct platform_device *pdev)
 	struct clk *xusbxti_clk;
 	u32 phyclk;
 
-	/* set clock frequency for PLL */
-	phyclk = readl(EXYNOS4_PHYCLK) & ~CLKSEL_MASK;
-
 	xusbxti_clk = clk_get(&pdev->dev, "xusbxti");
 	if (xusbxti_clk && !IS_ERR(xusbxti_clk)) {
-		switch (clk_get_rate(xusbxti_clk)) {
-		case 12 * MHZ:
-			phyclk |= CLKSEL_12M;
-			break;
-		case 24 * MHZ:
-			phyclk |= CLKSEL_24M;
-			break;
-		default:
-		case 48 * MHZ:
-			/* default reference clock */
-			break;
+		if (soc_is_exynos4210()) {
+			/* set clock frequency for PLL */
+			phyclk = readl(EXYNOS4_PHYCLK) & ~EXYNOS4210_CLKSEL_MASK;
+
+			switch (clk_get_rate(xusbxti_clk)) {
+			case 12 * MHZ:
+				phyclk |= EXYNOS4210_CLKSEL_12M;
+				break;
+			case 48 * MHZ:
+				phyclk |= EXYNOS4210_CLKSEL_48M;
+				break;
+			default:
+			case 24 * MHZ:
+				phyclk |= EXYNOS4210_CLKSEL_24M;
+				break;
+			}
+			writel(phyclk, EXYNOS4_PHYCLK);
+		} else if (soc_is_exynos4212() || soc_is_exynos4412()) {
+			/* set clock frequency for PLL */
+			phyclk = readl(EXYNOS4_PHYCLK) & ~EXYNOS4X12_CLKSEL_MASK;
+
+			switch (clk_get_rate(xusbxti_clk)) {
+			case 9600 * KHZ:
+				phyclk |= EXYNOS4X12_CLKSEL_9600K;
+				break;
+			case 10 * MHZ:
+				phyclk |= EXYNOS4X12_CLKSEL_10M;
+				break;
+			case 12 * MHZ:
+				phyclk |= EXYNOS4X12_CLKSEL_12M;
+				break;
+			case 19200 * KHZ:
+				phyclk |= EXYNOS4X12_CLKSEL_19200K;
+				break;
+			case 20 * MHZ:
+				phyclk |= EXYNOS4X12_CLKSEL_20M;
+				break;
+			default:
+			case 24 * MHZ:
+				/* default reference clock */
+				phyclk |= EXYNOS4X12_CLKSEL_24M;
+				break;
+			}
+			writel(phyclk, EXYNOS4_PHYCLK);
 		}
 		clk_put(xusbxti_clk);
 	}
-
-	writel(phyclk, EXYNOS4_PHYCLK);
 }
 
 static int exynos4210_usb_phy0_init(struct platform_device *pdev)

arch/arm/mach-imx/Kconfig

@@ -73,7 +73,7 @@ config SOC_IMX31
 
 config SOC_IMX35
 	bool
-	select CPU_V6
+	select CPU_V6K
 	select ARCH_MXC_IOMUX_V3
 	select COMMON_CLK
 	select HAVE_EPIT
@@ -588,6 +588,7 @@ config MACH_MX35_3DS
 	select IMX_HAVE_PLATFORM_IPU_CORE
 	select IMX_HAVE_PLATFORM_MXC_EHCI
 	select IMX_HAVE_PLATFORM_MXC_NAND
+	select IMX_HAVE_PLATFORM_MXC_RTC
 	select IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX
 	help
 	  Include support for MX35PDK platform. This includes specific

arch/arm/mach-imx/devices-imx35.h

@@ -68,6 +68,10 @@ extern const struct imx_mxc_nand_data imx35_mxc_nand_data;
 #define imx35_add_mxc_nand(pdata)	\
 	imx_add_mxc_nand(&imx35_mxc_nand_data, pdata)
 
+extern const struct imx_mxc_rtc_data imx35_mxc_rtc_data;
+#define imx35_add_mxc_rtc()	\
+	imx_add_mxc_rtc(&imx35_mxc_rtc_data)
+
 extern const struct imx_mxc_w1_data imx35_mxc_w1_data;
 #define imx35_add_mxc_w1()	\
 	imx_add_mxc_w1(&imx35_mxc_w1_data)

arch/arm/mach-imx/ehci-imx25.c

@@ -24,14 +24,18 @@
 #define MX25_OTG_SIC_SHIFT	29
 #define MX25_OTG_SIC_MASK	(0x3 << MX25_OTG_SIC_SHIFT)
 #define MX25_OTG_PM_BIT		(1 << 24)
+#define MX25_OTG_PP_BIT		(1 << 11)
+#define MX25_OTG_OCPOL_BIT	(1 << 3)
 
 #define MX25_H1_SIC_SHIFT	21
 #define MX25_H1_SIC_MASK	(0x3 << MX25_H1_SIC_SHIFT)
+#define MX25_H1_PP_BIT		(1 << 18)
 #define MX25_H1_PM_BIT		(1 << 8)
 #define MX25_H1_IPPUE_UP_BIT	(1 << 7)
 #define MX25_H1_IPPUE_DOWN_BIT	(1 << 6)
 #define MX25_H1_TLL_BIT		(1 << 5)
 #define MX25_H1_USBTE_BIT	(1 << 4)
+#define MX25_H1_OCPOL_BIT	(1 << 2)
 
 int mx25_initialize_usb_hw(int port, unsigned int flags)
 {
@@ -41,21 +45,35 @@ int mx25_initialize_usb_hw(int port, unsigned int flags)
 
 	switch (port) {
 	case 0:	/* OTG port */
-		v &= ~(MX25_OTG_SIC_MASK | MX25_OTG_PM_BIT);
+		v &= ~(MX25_OTG_SIC_MASK | MX25_OTG_PM_BIT | MX25_OTG_PP_BIT |
+			MX25_OTG_OCPOL_BIT);
 		v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX25_OTG_SIC_SHIFT;
 
 		if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
 			v |= MX25_OTG_PM_BIT;
 
+		if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH)
+			v |= MX25_OTG_PP_BIT;
+
+		if (!(flags & MXC_EHCI_OC_PIN_ACTIVE_LOW))
+			v |= MX25_OTG_OCPOL_BIT;
+
 		break;
 	case 1: /* H1 port */
-		v &= ~(MX25_H1_SIC_MASK | MX25_H1_PM_BIT | MX25_H1_TLL_BIT |
-			MX25_H1_USBTE_BIT | MX25_H1_IPPUE_DOWN_BIT | MX25_H1_IPPUE_UP_BIT);
+		v &= ~(MX25_H1_SIC_MASK | MX25_H1_PM_BIT | MX25_H1_PP_BIT |
+			MX25_H1_OCPOL_BIT | MX25_H1_TLL_BIT | MX25_H1_USBTE_BIT |
+			MX25_H1_IPPUE_DOWN_BIT | MX25_H1_IPPUE_UP_BIT);
 		v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX25_H1_SIC_SHIFT;
 
 		if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
 			v |= MX25_H1_PM_BIT;
 
+		if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH)
+			v |= MX25_H1_PP_BIT;
+
+		if (!(flags & MXC_EHCI_OC_PIN_ACTIVE_LOW))
+			v |= MX25_H1_OCPOL_BIT;
+
 		if (!(flags & MXC_EHCI_TTL_ENABLED))
 			v |= MX25_H1_TLL_BIT;
 

arch/arm/mach-imx/ehci-imx35.c

@@ -24,14 +24,18 @@
 #define MX35_OTG_SIC_SHIFT	29
 #define MX35_OTG_SIC_MASK	(0x3 << MX35_OTG_SIC_SHIFT)
 #define MX35_OTG_PM_BIT		(1 << 24)
+#define MX35_OTG_PP_BIT		(1 << 11)
+#define MX35_OTG_OCPOL_BIT	(1 << 3)
 
 #define MX35_H1_SIC_SHIFT	21
 #define MX35_H1_SIC_MASK	(0x3 << MX35_H1_SIC_SHIFT)
+#define MX35_H1_PP_BIT		(1 << 18)
 #define MX35_H1_PM_BIT		(1 << 8)
 #define MX35_H1_IPPUE_UP_BIT	(1 << 7)
 #define MX35_H1_IPPUE_DOWN_BIT	(1 << 6)
 #define MX35_H1_TLL_BIT		(1 << 5)
 #define MX35_H1_USBTE_BIT	(1 << 4)
+#define MX35_H1_OCPOL_BIT	(1 << 2)
 
 int mx35_initialize_usb_hw(int port, unsigned int flags)
 {
@@ -41,21 +45,35 @@ int mx35_initialize_usb_hw(int port, unsigned int flags)
 
 	switch (port) {
 	case 0:	/* OTG port */
-		v &= ~(MX35_OTG_SIC_MASK | MX35_OTG_PM_BIT);
+		v &= ~(MX35_OTG_SIC_MASK | MX35_OTG_PM_BIT | MX35_OTG_PP_BIT |
+			MX35_OTG_OCPOL_BIT);
 		v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX35_OTG_SIC_SHIFT;
 
 		if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
 			v |= MX35_OTG_PM_BIT;
 
+		if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH)
+			v |= MX35_OTG_PP_BIT;
+
+		if (!(flags & MXC_EHCI_OC_PIN_ACTIVE_LOW))
+			v |= MX35_OTG_OCPOL_BIT;
+
 		break;
 	case 1: /* H1 port */
-		v &= ~(MX35_H1_SIC_MASK | MX35_H1_PM_BIT | MX35_H1_TLL_BIT |
-			MX35_H1_USBTE_BIT | MX35_H1_IPPUE_DOWN_BIT | MX35_H1_IPPUE_UP_BIT);
+		v &= ~(MX35_H1_SIC_MASK | MX35_H1_PM_BIT | MX35_H1_PP_BIT |
+			MX35_H1_OCPOL_BIT | MX35_H1_TLL_BIT | MX35_H1_USBTE_BIT |
+			MX35_H1_IPPUE_DOWN_BIT | MX35_H1_IPPUE_UP_BIT);
 		v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX35_H1_SIC_SHIFT;
 
 		if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
 			v |= MX35_H1_PM_BIT;
 
+		if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH)
+			v |= MX35_H1_PP_BIT;
+
+		if (!(flags & MXC_EHCI_OC_PIN_ACTIVE_LOW))
+			v |= MX35_H1_OCPOL_BIT;
+
 		if (!(flags & MXC_EHCI_TTL_ENABLED))
 			v |= MX35_H1_TLL_BIT;
 

arch/arm/mach-imx/ehci-imx5.c

@@ -28,11 +28,14 @@
 #define MXC_OTG_UCTRL_OPM_BIT		(1 << 24)	/* OTG power mask */
 #define MXC_H1_UCTRL_H1UIE_BIT		(1 << 12)	/* Host1 ULPI interrupt enable */
 #define MXC_H1_UCTRL_H1WIE_BIT		(1 << 11)	/* HOST1 wakeup intr enable */
-#define MXC_H1_UCTRL_H1PM_BIT		(1 <<  8)		/* HOST1 power mask */
+#define MXC_H1_UCTRL_H1PM_BIT		(1 <<  8)	/* HOST1 power mask */
 
 /* USB_PHY_CTRL_FUNC */
+#define MXC_OTG_PHYCTRL_OC_POL_BIT	(1 << 9)	/* OTG Polarity of Overcurrent */
 #define MXC_OTG_PHYCTRL_OC_DIS_BIT	(1 << 8)	/* OTG Disable Overcurrent Event */
+#define MXC_H1_OC_POL_BIT		(1 << 6)	/* UH1 Polarity of Overcurrent */
 #define MXC_H1_OC_DIS_BIT		(1 << 5)	/* UH1 Disable Overcurrent Event */
+#define MXC_OTG_PHYCTRL_PWR_POL_BIT	(1 << 3)	/* OTG Power Pin Polarity */
 
 /* USBH2CTRL */
 #define MXC_H2_UCTRL_H2UIE_BIT		(1 << 8)
@@ -80,13 +83,21 @@ int mx51_initialize_usb_hw(int port, unsigned int flags)
 		if (flags & MXC_EHCI_INTERNAL_PHY) {
 			v = __raw_readl(usbother_base + MXC_USB_PHY_CTR_FUNC_OFFSET);
 
+			if (flags & MXC_EHCI_OC_PIN_ACTIVE_LOW)
+				v |= MXC_OTG_PHYCTRL_OC_POL_BIT;
+			else
+				v &= ~MXC_OTG_PHYCTRL_OC_POL_BIT;
 			if (flags & MXC_EHCI_POWER_PINS_ENABLED) {
-				/* OC/USBPWR is not used */
-				v |= MXC_OTG_PHYCTRL_OC_DIS_BIT;
-			} else {
 				/* OC/USBPWR is used */
 				v &= ~MXC_OTG_PHYCTRL_OC_DIS_BIT;
+			} else {
+				/* OC/USBPWR is not used */
+				v |= MXC_OTG_PHYCTRL_OC_DIS_BIT;
 			}
+			if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH)
+				v |= MXC_OTG_PHYCTRL_PWR_POL_BIT;
+			else
+				v &= ~MXC_OTG_PHYCTRL_PWR_POL_BIT;
 			__raw_writel(v, usbother_base + MXC_USB_PHY_CTR_FUNC_OFFSET);
 
 			v = __raw_readl(usbother_base + MXC_USBCTRL_OFFSET);
@@ -95,9 +106,9 @@ int mx51_initialize_usb_hw(int port, unsigned int flags)
 			else
 				v &= ~MXC_OTG_UCTRL_OWIE_BIT;/* OTG wakeup disable */
 			if (flags & MXC_EHCI_POWER_PINS_ENABLED)
-				v |= MXC_OTG_UCTRL_OPM_BIT;
-			else
 				v &= ~MXC_OTG_UCTRL_OPM_BIT;
+			else
+				v |= MXC_OTG_UCTRL_OPM_BIT;
 			__raw_writel(v, usbother_base + MXC_USBCTRL_OFFSET);
 		}
 		break;
@@ -113,12 +124,16 @@ int mx51_initialize_usb_hw(int port, unsigned int flags)
 		}
 
 		if (flags & MXC_EHCI_POWER_PINS_ENABLED)
-			v &= ~MXC_H1_UCTRL_H1PM_BIT; /* HOST1 power mask used*/
+			v &= ~MXC_H1_UCTRL_H1PM_BIT; /* HOST1 power mask unused*/
 		else
 			v |= MXC_H1_UCTRL_H1PM_BIT; /* HOST1 power mask used*/
 		__raw_writel(v, usbother_base + MXC_USBCTRL_OFFSET);
 
 		v = __raw_readl(usbother_base + MXC_USB_PHY_CTR_FUNC_OFFSET);
+		if (flags & MXC_EHCI_OC_PIN_ACTIVE_LOW)
+			v |= MXC_H1_OC_POL_BIT;
+		else
+			v &= ~MXC_H1_OC_POL_BIT;
 		if (flags & MXC_EHCI_POWER_PINS_ENABLED)
 			v &= ~MXC_H1_OC_DIS_BIT; /* OC is used */
 		else
@@ -142,7 +157,7 @@ int mx51_initialize_usb_hw(int port, unsigned int flags)
 		}
 
 		if (flags & MXC_EHCI_POWER_PINS_ENABLED)
-			v &= ~MXC_H2_UCTRL_H2PM_BIT; /* HOST2 power mask used*/
+			v &= ~MXC_H2_UCTRL_H2PM_BIT; /* HOST2 power mask unused*/
 		else
 			v |= MXC_H2_UCTRL_H2PM_BIT; /* HOST2 power mask used*/
 		__raw_writel(v, usbother_base + MXC_USBH2CTRL_OFFSET);

arch/arm/mach-imx/mach-mx35_3ds.c

@@ -572,6 +572,7 @@ static void __init mx35_3ds_init(void)
 
 	imx35_add_fec(NULL);
 	imx35_add_imx2_wdt();
+	imx35_add_mxc_rtc();
 	platform_add_devices(devices, ARRAY_SIZE(devices));
 
 	imx35_add_imx_uart0(&uart_pdata);

arch/arm/mach-lpc32xx/Kconfig

-if ARCH_LPC32XX
-
-menu "Individual UART enable selections"
-
-config ARCH_LPC32XX_UART3_SELECT
-	bool "Add support for standard UART3"
-	help
-	 Adds support for standard UART 3 when the 8250 serial support
-	 is enabled.
-
-config ARCH_LPC32XX_UART4_SELECT
-	bool "Add support for standard UART4"
-	help
-	 Adds support for standard UART 4 when the 8250 serial support
-	 is enabled.
-
-config ARCH_LPC32XX_UART5_SELECT
-	bool "Add support for standard UART5"
-	default y
-	help
-	 Adds support for standard UART 5 when the 8250 serial support
-	 is enabled.
-
-config ARCH_LPC32XX_UART6_SELECT
-	bool "Add support for standard UART6"
-	help
-	 Adds support for standard UART 6 when the 8250 serial support
-	 is enabled.
-
-endmenu
-
-endif

arch/arm/mach-lpc32xx/Makefile.boot

@@ -2,3 +2,4 @@
 params_phys-y	:= 0x80000100
 initrd_phys-y	:= 0x82000000
 
+dtb-$(CONFIG_ARCH_LPC32XX) += ea3250.dtb phy3250.dtb

arch/arm/mach-lpc32xx/clock.c

@@ -607,6 +607,19 @@ static struct clk clk_dma = {
 	.get_rate	= local_return_parent_rate,
 };
 
+static struct clk clk_pwm = {
+	.parent		= &clk_pclk,
+	.enable		= local_onoff_enable,
+	.enable_reg	= LPC32XX_CLKPWR_PWM_CLK_CTRL,
+	.enable_mask	= LPC32XX_CLKPWR_PWMCLK_PWM1CLK_EN |
+			  LPC32XX_CLKPWR_PWMCLK_PWM1SEL_PCLK |
+			  LPC32XX_CLKPWR_PWMCLK_PWM1_DIV(1) |
+			  LPC32XX_CLKPWR_PWMCLK_PWM2CLK_EN |
+			  LPC32XX_CLKPWR_PWMCLK_PWM2SEL_PCLK |
+			  LPC32XX_CLKPWR_PWMCLK_PWM2_DIV(1),
+	.get_rate	= local_return_parent_rate,
+};
+
 static struct clk clk_uart3 = {
 	.parent		= &clk_pclk,
 	.enable		= local_onoff_enable,
@@ -691,10 +704,21 @@ static struct clk clk_nand = {
 	.parent		= &clk_hclk,
 	.enable		= local_onoff_enable,
 	.enable_reg	= LPC32XX_CLKPWR_NAND_CLK_CTRL,
-	.enable_mask	= LPC32XX_CLKPWR_NANDCLK_SLCCLK_EN,
+	.enable_mask	= LPC32XX_CLKPWR_NANDCLK_SLCCLK_EN |
+			  LPC32XX_CLKPWR_NANDCLK_SEL_SLC,
 	.get_rate	= local_return_parent_rate,
 };
 
+static struct clk clk_nand_mlc = {
+	.parent         = &clk_hclk,
+	.enable         = local_onoff_enable,
+	.enable_reg     = LPC32XX_CLKPWR_NAND_CLK_CTRL,
+	.enable_mask    = LPC32XX_CLKPWR_NANDCLK_MLCCLK_EN |
+			  LPC32XX_CLKPWR_NANDCLK_DMA_INT |
+			  LPC32XX_CLKPWR_NANDCLK_INTSEL_MLC,
+	.get_rate       = local_return_parent_rate,
+};
+
 static struct clk clk_i2s0 = {
 	.parent		= &clk_hclk,
 	.enable		= local_onoff_enable,
@@ -707,7 +731,8 @@ static struct clk clk_i2s1 = {
 	.parent		= &clk_hclk,
 	.enable		= local_onoff_enable,
 	.enable_reg	= LPC32XX_CLKPWR_I2S_CLK_CTRL,
-	.enable_mask	= LPC32XX_CLKPWR_I2SCTRL_I2SCLK1_EN,
+	.enable_mask	= LPC32XX_CLKPWR_I2SCTRL_I2SCLK1_EN |
+			  LPC32XX_CLKPWR_I2SCTRL_I2S1_USE_DMA,
 	.get_rate	= local_return_parent_rate,
 };
 
@@ -727,14 +752,77 @@ static struct clk clk_rtc = {
 	.get_rate	= local_return_parent_rate,
 };
 
+static int local_usb_enable(struct clk *clk, int enable)
+{
+	u32 tmp;
+
+	if (enable) {
+		/* Set up I2C pull levels */
+		tmp = __raw_readl(LPC32XX_CLKPWR_I2C_CLK_CTRL);
+		tmp |= LPC32XX_CLKPWR_I2CCLK_USBI2CHI_DRIVE;
+		__raw_writel(tmp, LPC32XX_CLKPWR_I2C_CLK_CTRL);
+	}
+
+	return local_onoff_enable(clk, enable);
+}
+
 static struct clk clk_usbd = {
 	.parent		= &clk_usbpll,
-	.enable		= local_onoff_enable,
+	.enable		= local_usb_enable,
 	.enable_reg	= LPC32XX_CLKPWR_USB_CTRL,
 	.enable_mask	= LPC32XX_CLKPWR_USBCTRL_HCLK_EN,
 	.get_rate	= local_return_parent_rate,
 };
 
+#define OTG_ALWAYS_MASK		(LPC32XX_USB_OTG_OTG_CLOCK_ON | \
+				 LPC32XX_USB_OTG_I2C_CLOCK_ON)
+
+static int local_usb_otg_enable(struct clk *clk, int enable)
+{
+	int to = 1000;
+
+	if (enable) {
+		__raw_writel(clk->enable_mask, clk->enable_reg);
+
+		while (((__raw_readl(LPC32XX_USB_OTG_CLK_STAT) &
+			clk->enable_mask) != clk->enable_mask) && (to > 0))
+			to--;
+	} else {
+		__raw_writel(OTG_ALWAYS_MASK, clk->enable_reg);
+
+		while (((__raw_readl(LPC32XX_USB_OTG_CLK_STAT) &
+			OTG_ALWAYS_MASK) != OTG_ALWAYS_MASK) && (to > 0))
+			to--;
+	}
+
+	if (to)
+		return 0;
+	else
+		return -1;
+}
+
+static struct clk clk_usb_otg_dev = {
+	.parent		= &clk_usbpll,
+	.enable		= local_usb_otg_enable,
+	.enable_reg	= LPC32XX_USB_OTG_CLK_CTRL,
+	.enable_mask	= LPC32XX_USB_OTG_AHB_M_CLOCK_ON |
+			  LPC32XX_USB_OTG_OTG_CLOCK_ON |
+			  LPC32XX_USB_OTG_DEV_CLOCK_ON |
+			  LPC32XX_USB_OTG_I2C_CLOCK_ON,
+	.get_rate	= local_return_parent_rate,
+};
+
+static struct clk clk_usb_otg_host = {
+	.parent		= &clk_usbpll,
+	.enable		= local_usb_otg_enable,
+	.enable_reg	= LPC32XX_USB_OTG_CLK_CTRL,
+	.enable_mask	= LPC32XX_USB_OTG_AHB_M_CLOCK_ON |
+			  LPC32XX_USB_OTG_OTG_CLOCK_ON |
+			  LPC32XX_USB_OTG_HOST_CLOCK_ON |
+			  LPC32XX_USB_OTG_I2C_CLOCK_ON,
+	.get_rate	= local_return_parent_rate,
+};
+
 static int tsc_onoff_enable(struct clk *clk, int enable)
 {
 	u32 tmp;
@@ -800,11 +888,17 @@ static int mmc_onoff_enable(struct clk *clk, int enable)
 	u32 tmp;
 
 	tmp = __raw_readl(LPC32XX_CLKPWR_MS_CTRL) &
-		~LPC32XX_CLKPWR_MSCARD_SDCARD_EN;
+		~(LPC32XX_CLKPWR_MSCARD_SDCARD_EN |
+		  LPC32XX_CLKPWR_MSCARD_MSDIO_PU_EN |
+		  LPC32XX_CLKPWR_MSCARD_MSDIO_PIN_DIS |
+		  LPC32XX_CLKPWR_MSCARD_MSDIO0_DIS |
+		  LPC32XX_CLKPWR_MSCARD_MSDIO1_DIS |
+		  LPC32XX_CLKPWR_MSCARD_MSDIO23_DIS);
 
 	/* If rate is 0, disable clock */
 	if (enable != 0)
-		tmp |= LPC32XX_CLKPWR_MSCARD_SDCARD_EN;
+		tmp |= LPC32XX_CLKPWR_MSCARD_SDCARD_EN |
+			LPC32XX_CLKPWR_MSCARD_MSDIO_PU_EN;
 
 	__raw_writel(tmp, LPC32XX_CLKPWR_MS_CTRL);
 
@@ -853,7 +947,7 @@ static unsigned long mmc_round_rate(struct clk *clk, unsigned long rate)
 
 static int mmc_set_rate(struct clk *clk, unsigned long rate)
 {
-	u32 oldclk, tmp;
+	u32 tmp;
 	unsigned long prate, div, crate = mmc_round_rate(clk, rate);
 
 	prate = clk->parent->get_rate(clk->parent);
@@ -861,16 +955,12 @@ static int mmc_set_rate(struct clk *clk, unsigned long rate)
 	div = prate / crate;
 
 	/* The MMC clock must be on when accessing an MMC register */
-	oldclk = __raw_readl(LPC32XX_CLKPWR_MS_CTRL);
-	__raw_writel(oldclk | LPC32XX_CLKPWR_MSCARD_SDCARD_EN,
-		LPC32XX_CLKPWR_MS_CTRL);
 	tmp = __raw_readl(LPC32XX_CLKPWR_MS_CTRL) &
 		~LPC32XX_CLKPWR_MSCARD_SDCARD_DIV(0xf);
-	tmp |= LPC32XX_CLKPWR_MSCARD_SDCARD_DIV(div);
+	tmp |= LPC32XX_CLKPWR_MSCARD_SDCARD_DIV(div) |
+		LPC32XX_CLKPWR_MSCARD_SDCARD_EN;
 	__raw_writel(tmp, LPC32XX_CLKPWR_MS_CTRL);
 
-	__raw_writel(oldclk, LPC32XX_CLKPWR_MS_CTRL);
-
 	return 0;
 }
 
@@ -1111,6 +1201,7 @@ static struct clk_lookup lookups[] = {
 	CLKDEV_INIT(NULL, "vfp9_ck", &clk_vfp9),
 	CLKDEV_INIT("pl08xdmac", NULL, &clk_dma),
 	CLKDEV_INIT("4003c000.watchdog", NULL, &clk_wdt),
+	CLKDEV_INIT("4005c000.pwm", NULL, &clk_pwm),
 	CLKDEV_INIT(NULL, "uart3_ck", &clk_uart3),
 	CLKDEV_INIT(NULL, "uart4_ck", &clk_uart4),
 	CLKDEV_INIT(NULL, "uart5_ck", &clk_uart5),
@@ -1120,8 +1211,9 @@ static struct clk_lookup lookups[] = {
 	CLKDEV_INIT("31020300.i2c", NULL, &clk_i2c2),
 	CLKDEV_INIT("dev:ssp0", NULL, &clk_ssp0),
 	CLKDEV_INIT("dev:ssp1", NULL, &clk_ssp1),
-	CLKDEV_INIT("lpc32xx_keys.0", NULL, &clk_kscan),
-	CLKDEV_INIT("lpc32xx-nand.0", "nand_ck", &clk_nand),
+	CLKDEV_INIT("40050000.key", NULL, &clk_kscan),
+	CLKDEV_INIT("20020000.flash", NULL, &clk_nand),
+	CLKDEV_INIT("200a8000.flash", NULL, &clk_nand_mlc),
 	CLKDEV_INIT("40048000.adc", NULL, &clk_adc),
 	CLKDEV_INIT(NULL, "i2s0_ck", &clk_i2s0),
 	CLKDEV_INIT(NULL, "i2s1_ck", &clk_i2s1),
@@ -1130,6 +1222,9 @@ static struct clk_lookup lookups[] = {
 	CLKDEV_INIT("31060000.ethernet", NULL, &clk_net),
 	CLKDEV_INIT("dev:clcd", NULL, &clk_lcd),
 	CLKDEV_INIT("31020000.usbd", "ck_usbd", &clk_usbd),
+	CLKDEV_INIT("31020000.ohci", "ck_usbd", &clk_usbd),
+	CLKDEV_INIT("31020000.usbd", "ck_usb_otg", &clk_usb_otg_dev),
+	CLKDEV_INIT("31020000.ohci", "ck_usb_otg", &clk_usb_otg_host),
 	CLKDEV_INIT("lpc32xx_rtc", NULL, &clk_rtc),
 };
 

arch/arm/mach-lpc32xx/common.c

@@ -26,6 +26,7 @@
 #include <linux/io.h>
 
 #include <asm/mach/map.h>
+#include <asm/system_info.h>
 
 #include <mach/hardware.h>
 #include <mach/platform.h>
@@ -224,7 +225,7 @@ void lpc23xx_restart(char mode, const char *cmd)
 		;
 }
 
-static int __init lpc32xx_display_uid(void)
+static int __init lpc32xx_check_uid(void)
 {
 	u32 uid[4];
 
@@ -233,6 +234,11 @@ static int __init lpc32xx_display_uid(void)
 	printk(KERN_INFO "LPC32XX unique ID: %08x%08x%08x%08x\n",
 		uid[3], uid[2], uid[1], uid[0]);
 
+	if (!system_serial_low && !system_serial_high) {
+		system_serial_low = uid[0];
+		system_serial_high = uid[1];
+	}
+
 	return 1;
 }
-arch_initcall(lpc32xx_display_uid);
+arch_initcall(lpc32xx_check_uid);

arch/arm/mach-lpc32xx/include/mach/gpio.h

@@ -3,6 +3,4 @@
 
 #include "gpio-lpc32xx.h"
 
-#define ARCH_NR_GPIOS (LPC32XX_GPO_P3_GRP + LPC32XX_GPO_P3_MAX)
-
 #endif /* __MACH_GPIO_H */

arch/arm/mach-lpc32xx/include/mach/platform.h

@@ -694,4 +694,18 @@
 #define LPC32XX_GPIO_P2_MUX_CLR			_GPREG(0x02C)
 #define LPC32XX_GPIO_P2_MUX_STATE		_GPREG(0x030)
 
+/*
+ * USB Otg Registers
+ */
+#define _OTGREG(x)			io_p2v(LPC32XX_USB_OTG_BASE + (x))
+#define LPC32XX_USB_OTG_CLK_CTRL	_OTGREG(0xFF4)
+#define LPC32XX_USB_OTG_CLK_STAT	_OTGREG(0xFF8)
+
+/* USB OTG CLK CTRL bit defines */
+#define LPC32XX_USB_OTG_AHB_M_CLOCK_ON	_BIT(4)
+#define LPC32XX_USB_OTG_OTG_CLOCK_ON	_BIT(3)
+#define LPC32XX_USB_OTG_I2C_CLOCK_ON	_BIT(2)
+#define LPC32XX_USB_OTG_DEV_CLOCK_ON	_BIT(1)
+#define LPC32XX_USB_OTG_HOST_CLOCK_ON	_BIT(0)
+
 #endif

arch/arm/mach-lpc32xx/phy3250.c

@@ -30,12 +30,13 @@
 #include <linux/amba/bus.h>
 #include <linux/amba/clcd.h>
 #include <linux/amba/pl022.h>
+#include <linux/amba/pl08x.h>
+#include <linux/amba/mmci.h>
 #include <linux/of.h>
 #include <linux/of_address.h>
 #include <linux/of_irq.h>
 #include <linux/of_platform.h>
 #include <linux/clk.h>
-#include <linux/amba/pl08x.h>
 
 #include <asm/setup.h>
 #include <asm/mach-types.h>
@@ -50,9 +51,9 @@
 /*
  * Mapped GPIOLIB GPIOs
  */
-#define SPI0_CS_GPIO	LPC32XX_GPIO(LPC32XX_GPIO_P3_GRP, 5)
-#define LCD_POWER_GPIO	LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 0)
-#define BKL_POWER_GPIO	LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 4)
+#define LCD_POWER_GPIO		LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 0)
+#define BKL_POWER_GPIO		LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 4)
+#define MMC_PWR_ENABLE_GPIO	LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 5)
 
 /*
  * AMBA LCD controller
@@ -158,24 +159,6 @@ static struct clcd_board lpc32xx_clcd_data = {
 /*
  * AMBA SSP (SPI)
  */
-static void phy3250_spi_cs_set(u32 control)
-{
-	gpio_set_value(SPI0_CS_GPIO, (int) control);
-}
-
-static struct pl022_config_chip spi0_chip_info = {
-	.com_mode		= INTERRUPT_TRANSFER,
-	.iface			= SSP_INTERFACE_MOTOROLA_SPI,
-	.hierarchy		= SSP_MASTER,
-	.slave_tx_disable	= 0,
-	.rx_lev_trig		= SSP_RX_4_OR_MORE_ELEM,
-	.tx_lev_trig		= SSP_TX_4_OR_MORE_EMPTY_LOC,
-	.ctrl_len		= SSP_BITS_8,
-	.wait_state		= SSP_MWIRE_WAIT_ZERO,
-	.duplex			= SSP_MICROWIRE_CHANNEL_FULL_DUPLEX,
-	.cs_control		= phy3250_spi_cs_set,
-};
-
 static struct pl022_ssp_controller lpc32xx_ssp0_data = {
 	.bus_id			= 0,
 	.num_chipselect		= 1,
@@ -188,45 +171,56 @@ static struct pl022_ssp_controller lpc32xx_ssp1_data = {
 	.enable_dma		= 0,
 };
 
-/* AT25 driver registration */
-static int __init phy3250_spi_board_register(void)
+static struct pl08x_channel_data pl08x_slave_channels[] = {
+	{
+		.bus_id = "nand-slc",
+		.min_signal = 1, /* SLC NAND Flash */
+		.max_signal = 1,
+		.periph_buses = PL08X_AHB1,
+	},
+	{
+		.bus_id = "nand-mlc",
+		.min_signal = 12, /* MLC NAND Flash */
+		.max_signal = 12,
+		.periph_buses = PL08X_AHB1,
+	},
+};
+
+static int pl08x_get_signal(const struct pl08x_channel_data *cd)
+{
+	return cd->min_signal;
+}
+
+static void pl08x_put_signal(const struct pl08x_channel_data *cd, int ch)
 {
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
-	static struct spi_board_info info[] = {
-		{
-			.modalias = "spidev",
-			.max_speed_hz = 5000000,
-			.bus_num = 0,
-			.chip_select = 0,
-			.controller_data = &spi0_chip_info,
-		},
-	};
-
-#else
-	static struct spi_eeprom eeprom = {
-		.name = "at25256a",
-		.byte_len = 0x8000,
-		.page_size = 64,
-		.flags = EE_ADDR2,
-	};
-
-	static struct spi_board_info info[] = {
-		{
-			.modalias = "at25",
-			.max_speed_hz = 5000000,
-			.bus_num = 0,
-			.chip_select = 0,
-			.mode = SPI_MODE_0,
-			.platform_data = &eeprom,
-			.controller_data = &spi0_chip_info,
-		},
-	};
-#endif
-	return spi_register_board_info(info, ARRAY_SIZE(info));
 }
-arch_initcall(phy3250_spi_board_register);
 
 static struct pl08x_platform_data pl08x_pd = {
+	.slave_channels = &pl08x_slave_channels[0],
+	.num_slave_channels = ARRAY_SIZE(pl08x_slave_channels),
+	.get_signal = pl08x_get_signal,
+	.put_signal = pl08x_put_signal,
+	.lli_buses = PL08X_AHB1,
+	.mem_buses = PL08X_AHB1,
+};
+
+static int mmc_handle_ios(struct device *dev, struct mmc_ios *ios)
+{
+	/* Only on and off are supported */
+	if (ios->power_mode == MMC_POWER_OFF)
+		gpio_set_value(MMC_PWR_ENABLE_GPIO, 0);
+	else
+		gpio_set_value(MMC_PWR_ENABLE_GPIO, 1);
+	return 0;
+}
+
+static struct mmci_platform_data lpc32xx_mmci_data = {
+	.ocr_mask	= MMC_VDD_30_31 | MMC_VDD_31_32 |
+			  MMC_VDD_32_33 | MMC_VDD_33_34,
+	.ios_handler	= mmc_handle_ios,
+	.dma_filter	= NULL,
+	/* No DMA for now since AMBA PL080 dmaengine driver only does scatter
+	 * gather, and the MMCI driver doesn't do it this way */
 };
 
 static const struct of_dev_auxdata lpc32xx_auxdata_lookup[] __initconst = {
@@ -234,6 +228,8 @@ static const struct of_dev_auxdata lpc32xx_auxdata_lookup[] __initconst = {
 	OF_DEV_AUXDATA("arm,pl022", 0x2008C000, "dev:ssp1", &lpc32xx_ssp1_data),
 	OF_DEV_AUXDATA("arm,pl110", 0x31040000, "dev:clcd", &lpc32xx_clcd_data),
 	OF_DEV_AUXDATA("arm,pl080", 0x31000000, "pl08xdmac", &pl08x_pd),
+	OF_DEV_AUXDATA("arm,pl18x", 0x20098000, "20098000.sd",
+		       &lpc32xx_mmci_data),
 	{ }
 };
 
@@ -241,10 +237,6 @@ static void __init lpc3250_machine_init(void)
 {
 	u32 tmp;
 
-	/* Setup SLC NAND controller muxing */
-	__raw_writel(LPC32XX_CLKPWR_NANDCLK_SEL_SLC,
-		LPC32XX_CLKPWR_NAND_CLK_CTRL);
-
 	/* Setup LCD muxing to RGB565 */
 	tmp = __raw_readl(LPC32XX_CLKPWR_LCDCLK_CTRL) &
 		~(LPC32XX_CLKPWR_LCDCTRL_LCDTYPE_MSK |
@@ -252,47 +244,8 @@ static void __init lpc3250_machine_init(void)
 	tmp |= LPC32XX_CLKPWR_LCDCTRL_LCDTYPE_TFT16;
 	__raw_writel(tmp, LPC32XX_CLKPWR_LCDCLK_CTRL);
 
-	/* Set up USB power */
-	tmp = __raw_readl(LPC32XX_CLKPWR_USB_CTRL);
-	tmp |= LPC32XX_CLKPWR_USBCTRL_HCLK_EN |
-		LPC32XX_CLKPWR_USBCTRL_USBI2C_EN;
-	__raw_writel(tmp, LPC32XX_CLKPWR_USB_CTRL);
-
-	/* Set up I2C pull levels */
-	tmp = __raw_readl(LPC32XX_CLKPWR_I2C_CLK_CTRL);
-	tmp |= LPC32XX_CLKPWR_I2CCLK_USBI2CHI_DRIVE |
-		LPC32XX_CLKPWR_I2CCLK_I2C2HI_DRIVE;
-	__raw_writel(tmp, LPC32XX_CLKPWR_I2C_CLK_CTRL);
-
-	/* Disable IrDA pulsing support on UART6 */
-	tmp = __raw_readl(LPC32XX_UARTCTL_CTRL);
-	tmp |= LPC32XX_UART_UART6_IRDAMOD_BYPASS;
-	__raw_writel(tmp, LPC32XX_UARTCTL_CTRL);
-
-	/* Enable DMA for I2S1 channel */
-	tmp = __raw_readl(LPC32XX_CLKPWR_I2S_CLK_CTRL);
-	tmp = LPC32XX_CLKPWR_I2SCTRL_I2S1_USE_DMA;
-	__raw_writel(tmp, LPC32XX_CLKPWR_I2S_CLK_CTRL);
-
 	lpc32xx_serial_init();
 
-	/*
-	 * AMBA peripheral clocks need to be enabled prior to AMBA device
-	 * detection or a data fault will occur, so enable the clocks
-	 * here.
-	 */
-	tmp = __raw_readl(LPC32XX_CLKPWR_LCDCLK_CTRL);
-	__raw_writel((tmp | LPC32XX_CLKPWR_LCDCTRL_CLK_EN),
-		LPC32XX_CLKPWR_LCDCLK_CTRL);
-
-	tmp = __raw_readl(LPC32XX_CLKPWR_SSP_CLK_CTRL);
-	__raw_writel((tmp | LPC32XX_CLKPWR_SSPCTRL_SSPCLK0_EN),
-		LPC32XX_CLKPWR_SSP_CLK_CTRL);
-
-	tmp = __raw_readl(LPC32XX_CLKPWR_DMA_CLK_CTRL);
-	__raw_writel((tmp | LPC32XX_CLKPWR_DMACLKCTRL_CLK_EN),
-		     LPC32XX_CLKPWR_DMA_CLK_CTRL);
-
 	/* Test clock needed for UDA1380 initial init */
 	__raw_writel(LPC32XX_CLKPWR_TESTCLK2_SEL_MOSC |
 		LPC32XX_CLKPWR_TESTCLK_TESTCLK2_EN,
@@ -302,12 +255,10 @@ static void __init lpc3250_machine_init(void)
 			     lpc32xx_auxdata_lookup, NULL);
 
 	/* Register GPIOs used on this board */
-	if (gpio_request(SPI0_CS_GPIO, "spi0 cs"))
-		printk(KERN_ERR "Error requesting gpio %u",
-			SPI0_CS_GPIO);
-	else if (gpio_direction_output(SPI0_CS_GPIO, 1))
-		printk(KERN_ERR "Error setting gpio %u to output",
-			SPI0_CS_GPIO);
+	if (gpio_request(MMC_PWR_ENABLE_GPIO, "mmc_power_en"))
+		pr_err("Error requesting gpio %u", MMC_PWR_ENABLE_GPIO);
+	else if (gpio_direction_output(MMC_PWR_ENABLE_GPIO, 1))
+		pr_err("Error setting gpio %u to output", MMC_PWR_ENABLE_GPIO);
 }
 
 static char const *lpc32xx_dt_compat[] __initdata = {

arch/arm/mach-lpc32xx/serial.c

@@ -31,59 +31,6 @@
 
 #define LPC32XX_SUART_FIFO_SIZE	64
 
-/* Standard 8250/16550 compatible serial ports */
-static struct plat_serial8250_port serial_std_platform_data[] = {
-#ifdef CONFIG_ARCH_LPC32XX_UART5_SELECT
-	{
-		.membase        = io_p2v(LPC32XX_UART5_BASE),
-		.mapbase        = LPC32XX_UART5_BASE,
-		.irq		= IRQ_LPC32XX_UART_IIR5,
-		.uartclk	= LPC32XX_MAIN_OSC_FREQ,
-		.regshift	= 2,
-		.iotype		= UPIO_MEM32,
-		.flags		= UPF_BOOT_AUTOCONF | UPF_BUGGY_UART |
-					UPF_SKIP_TEST,
-	},
-#endif
-#ifdef CONFIG_ARCH_LPC32XX_UART3_SELECT
-	{
-		.membase	= io_p2v(LPC32XX_UART3_BASE),
-		.mapbase        = LPC32XX_UART3_BASE,
-		.irq		= IRQ_LPC32XX_UART_IIR3,
-		.uartclk	= LPC32XX_MAIN_OSC_FREQ,
-		.regshift	= 2,
-		.iotype		= UPIO_MEM32,
-		.flags		= UPF_BOOT_AUTOCONF | UPF_BUGGY_UART |
-					UPF_SKIP_TEST,
-	},
-#endif
-#ifdef CONFIG_ARCH_LPC32XX_UART4_SELECT
-	{
-		.membase	= io_p2v(LPC32XX_UART4_BASE),
-		.mapbase        = LPC32XX_UART4_BASE,
-		.irq		= IRQ_LPC32XX_UART_IIR4,
-		.uartclk	= LPC32XX_MAIN_OSC_FREQ,
-		.regshift	= 2,
-		.iotype		= UPIO_MEM32,
-		.flags		= UPF_BOOT_AUTOCONF | UPF_BUGGY_UART |
-					UPF_SKIP_TEST,
-	},
-#endif
-#ifdef CONFIG_ARCH_LPC32XX_UART6_SELECT
-	{
-		.membase	= io_p2v(LPC32XX_UART6_BASE),
-		.mapbase        = LPC32XX_UART6_BASE,
-		.irq		= IRQ_LPC32XX_UART_IIR6,
-		.uartclk	= LPC32XX_MAIN_OSC_FREQ,
-		.regshift	= 2,
-		.iotype		= UPIO_MEM32,
-		.flags		= UPF_BOOT_AUTOCONF | UPF_BUGGY_UART |
-					UPF_SKIP_TEST,
-	},
-#endif
-	{ },
-};
-
 struct uartinit {
 	char *uart_ck_name;
 	u32 ck_mode_mask;
@@ -92,7 +39,6 @@ struct uartinit {
 };
 
 static struct uartinit uartinit_data[] __initdata = {
-#ifdef CONFIG_ARCH_LPC32XX_UART5_SELECT
 	{
 		.uart_ck_name = "uart5_ck",
 		.ck_mode_mask =
@@ -100,8 +46,6 @@ static struct uartinit uartinit_data[] __initdata = {
 		.pdiv_clk_reg = LPC32XX_CLKPWR_UART5_CLK_CTRL,
 		.mapbase = LPC32XX_UART5_BASE,
 	},
-#endif
-#ifdef CONFIG_ARCH_LPC32XX_UART3_SELECT
 	{
 		.uart_ck_name = "uart3_ck",
 		.ck_mode_mask =
@@ -109,8 +53,6 @@ static struct uartinit uartinit_data[] __initdata = {
 		.pdiv_clk_reg = LPC32XX_CLKPWR_UART3_CLK_CTRL,
 		.mapbase = LPC32XX_UART3_BASE,
 	},
-#endif
-#ifdef CONFIG_ARCH_LPC32XX_UART4_SELECT
 	{
 		.uart_ck_name = "uart4_ck",
 		.ck_mode_mask =
@@ -118,8 +60,6 @@ static struct uartinit uartinit_data[] __initdata = {
 		.pdiv_clk_reg = LPC32XX_CLKPWR_UART4_CLK_CTRL,
 		.mapbase = LPC32XX_UART4_BASE,
 	},
-#endif
-#ifdef CONFIG_ARCH_LPC32XX_UART6_SELECT
 	{
 		.uart_ck_name = "uart6_ck",
 		.ck_mode_mask =
@@ -127,19 +67,6 @@ static struct uartinit uartinit_data[] __initdata = {
 		.pdiv_clk_reg = LPC32XX_CLKPWR_UART6_CLK_CTRL,
 		.mapbase = LPC32XX_UART6_BASE,
 	},
-#endif
-};
-
-static struct platform_device serial_std_platform_device = {
-	.name			= "serial8250",
-	.id			= 0,
-	.dev			= {
-		.platform_data	= serial_std_platform_data,
-	},
-};
-
-static struct platform_device *lpc32xx_serial_devs[] __initdata = {
-	&serial_std_platform_device,
 };
 
 void __init lpc32xx_serial_init(void)
@@ -156,15 +83,8 @@ void __init lpc32xx_serial_init(void)
 		clk = clk_get(NULL, uartinit_data[i].uart_ck_name);
 		if (!IS_ERR(clk)) {
 			clk_enable(clk);
-			serial_std_platform_data[i].uartclk =
-				clk_get_rate(clk);
 		}
 
-		/* Fall back on main osc rate if clock rate return fails */
-		if (serial_std_platform_data[i].uartclk == 0)
-			serial_std_platform_data[i].uartclk =
-				LPC32XX_MAIN_OSC_FREQ;
-
 		/* Setup UART clock modes for all UARTs, disable autoclock */
 		clkmodes |= uartinit_data[i].ck_mode_mask;
 
@@ -189,7 +109,7 @@ void __init lpc32xx_serial_init(void)
 	__raw_writel(clkmodes, LPC32XX_UARTCTL_CLKMODE);
 	for (i = 0; i < ARRAY_SIZE(uartinit_data); i++) {
 		/* Force a flush of the RX FIFOs to work around a HW bug */
-		puart = serial_std_platform_data[i].mapbase;
+		puart = uartinit_data[i].mapbase;
 		__raw_writel(0xC1, LPC32XX_UART_IIR_FCR(puart));
 		__raw_writel(0x00, LPC32XX_UART_DLL_FIFO(puart));
 		j = LPC32XX_SUART_FIFO_SIZE;
@@ -198,11 +118,13 @@ void __init lpc32xx_serial_init(void)
 		__raw_writel(0, LPC32XX_UART_IIR_FCR(puart));
 	}
 
+	/* Disable IrDA pulsing support on UART6 */
+	tmp = __raw_readl(LPC32XX_UARTCTL_CTRL);
+	tmp |= LPC32XX_UART_UART6_IRDAMOD_BYPASS;
+	__raw_writel(tmp, LPC32XX_UARTCTL_CTRL);
+
 	/* Disable UART5->USB transparent mode or USB won't work */
 	tmp = __raw_readl(LPC32XX_UARTCTL_CTRL);
 	tmp &= ~LPC32XX_UART_U5_ROUTE_TO_USB;
 	__raw_writel(tmp, LPC32XX_UARTCTL_CTRL);
-
-	platform_add_devices(lpc32xx_serial_devs,
-		ARRAY_SIZE(lpc32xx_serial_devs));
 }

arch/arm/mach-nomadik/Makefile

@@ -7,8 +7,6 @@
 
 # Object file lists.
 
-obj-y			+= clock.o
-
 # Cpu revision
 obj-$(CONFIG_NOMADIK_8815) += cpu-8815.o
 

arch/arm/mach-nomadik/board-nhk8815.c

@@ -14,12 +14,14 @@
 #include <linux/init.h>
 #include <linux/platform_device.h>
 #include <linux/amba/bus.h>
+#include <linux/amba/mmci.h>
 #include <linux/interrupt.h>
 #include <linux/gpio.h>
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/nand.h>
 #include <linux/mtd/onenand.h>
 #include <linux/mtd/partitions.h>
+#include <linux/i2c.h>
 #include <linux/io.h>
 #include <asm/hardware/vic.h>
 #include <asm/sizes.h>
@@ -185,16 +187,28 @@ static void __init nhk8815_onenand_init(void)
 #endif
 }
 
-static AMBA_APB_DEVICE(uart0, "uart0", 0, NOMADIK_UART0_BASE,
-	{ IRQ_UART0 }, NULL);
+static struct mmci_platform_data mmcsd_plat_data = {
+	.ocr_mask = MMC_VDD_29_30,
+	.f_max = 48000000,
+	.gpio_wp = -1,
+	.gpio_cd = 111,
+	.cd_invert = true,
+	.capabilities = MMC_CAP_MMC_HIGHSPEED |
+	MMC_CAP_SD_HIGHSPEED | MMC_CAP_4_BIT_DATA,
+};
 
-static AMBA_APB_DEVICE(uart1, "uart1", 0, NOMADIK_UART1_BASE,
-	{ IRQ_UART1 }, NULL);
+static int __init nhk8815_mmcsd_init(void)
+{
+	int ret;
 
-static struct amba_device *amba_devs[] __initdata = {
-	&uart0_device,
-	&uart1_device,
-};
+	ret = gpio_request(112, "card detect bias");
+	if (ret)
+		return ret;
+	gpio_direction_output(112, 0);
+	amba_apb_device_add(NULL, "mmci", NOMADIK_SDI_BASE, SZ_4K, IRQ_SDMMC, 0, &mmcsd_plat_data, 0x10180180);
+	return 0;
+}
+module_init(nhk8815_mmcsd_init);
 
 static struct resource nhk8815_eth_resources[] = {
 	{
@@ -253,17 +267,46 @@ static struct sys_timer nomadik_timer = {
 	.init	= nomadik_timer_init,
 };
 
+static struct i2c_board_info __initdata nhk8815_i2c0_devices[] = {
+	{
+		I2C_BOARD_INFO("stw4811", 0x2d),
+	},
+};
+
+static struct i2c_board_info __initdata nhk8815_i2c1_devices[] = {
+	{
+		I2C_BOARD_INFO("camera", 0x10),
+	},
+	{
+		I2C_BOARD_INFO("stw5095", 0x1a),
+	},
+	{
+		I2C_BOARD_INFO("lis3lv02dl", 0x1d),
+	},
+};
+
+static struct i2c_board_info __initdata nhk8815_i2c2_devices[] = {
+	{
+		I2C_BOARD_INFO("stw4811-usb", 0x2d),
+	},
+};
+
 static void __init nhk8815_platform_init(void)
 {
-	int i;
-
 	cpu8815_platform_init();
 	nhk8815_onenand_init();
 	platform_add_devices(nhk8815_platform_devices,
 			     ARRAY_SIZE(nhk8815_platform_devices));
 
-	for (i = 0; i < ARRAY_SIZE(amba_devs); i++)
-		amba_device_register(amba_devs[i], &iomem_resource);
+	amba_apb_device_add(NULL, "uart0", NOMADIK_UART0_BASE, SZ_4K, IRQ_UART0, 0, NULL, 0);
+	amba_apb_device_add(NULL, "uart1", NOMADIK_UART1_BASE, SZ_4K, IRQ_UART1, 0, NULL, 0);
+
+	i2c_register_board_info(0, nhk8815_i2c0_devices,
+				ARRAY_SIZE(nhk8815_i2c0_devices));
+	i2c_register_board_info(1, nhk8815_i2c1_devices,
+				ARRAY_SIZE(nhk8815_i2c1_devices));
+	i2c_register_board_info(2, nhk8815_i2c2_devices,
+				ARRAY_SIZE(nhk8815_i2c2_devices));
 }
 
 MACHINE_START(NOMADIK, "NHK8815")

arch/arm/mach-nomadik/clock.c

-/*
- *  linux/arch/arm/mach-nomadik/clock.c
- *
- *  Copyright (C) 2009 Alessandro Rubini
- */
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/errno.h>
-#include <linux/clk.h>
-#include <linux/clkdev.h>
-#include "clock.h"
-
-/*
- * The nomadik board uses generic clocks, but the serial pl011 file
- * calls clk_enable(), clk_disable(), clk_get_rate(), so we provide them
- */
-unsigned long clk_get_rate(struct clk *clk)
-{
-	return clk->rate;
-}
-EXPORT_SYMBOL(clk_get_rate);
-
-/* enable and disable do nothing */
-int clk_enable(struct clk *clk)
-{
-	return 0;
-}
-EXPORT_SYMBOL(clk_enable);
-
-void clk_disable(struct clk *clk)
-{
-}
-EXPORT_SYMBOL(clk_disable);
-
-static struct clk clk_24 = {
-	.rate = 2400000,
-};
-
-static struct clk clk_48 = {
-	.rate = 48 * 1000 * 1000,
-};
-
-/*
- * Catch-all default clock to satisfy drivers using the clk API.  We don't
- * model the actual hardware clocks yet.
- */
-static struct clk clk_default;
-
-#define CLK(_clk, dev)				\
-	{					\
-		.clk		= _clk,		\
-		.dev_id		= dev,		\
-	}
-
-static struct clk_lookup lookups[] = {
-	{
-		.con_id		= "apb_pclk",
-		.clk		= &clk_default,
-	},
-	CLK(&clk_24, "mtu0"),
-	CLK(&clk_24, "mtu1"),
-	CLK(&clk_48, "uart0"),
-	CLK(&clk_48, "uart1"),
-	CLK(&clk_default, "gpio.0"),
-	CLK(&clk_default, "gpio.1"),
-	CLK(&clk_default, "gpio.2"),
-	CLK(&clk_default, "gpio.3"),
-	CLK(&clk_default, "rng"),
-};
-
-int __init clk_init(void)
-{
-	clkdev_add_table(lookups, ARRAY_SIZE(lookups));
-	return 0;
-}

arch/arm/mach-nomadik/clock.h

-
-/*
- *  linux/arch/arm/mach-nomadik/clock.h
- *
- *  Copyright (C) 2009 Alessandro Rubini
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-struct clk {
-	unsigned long		rate;
-};
-
-int __init clk_init(void);

arch/arm/mach-nomadik/cpu-8815.c

@@ -22,6 +22,10 @@
 #include <linux/amba/bus.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
+#include <linux/slab.h>
+#include <linux/irq.h>
+#include <linux/dma-mapping.h>
+#include <linux/platform_data/clk-nomadik.h>
 
 #include <plat/gpio-nomadik.h>
 #include <mach/hardware.h>
@@ -32,91 +36,63 @@
 #include <asm/cacheflush.h>
 #include <asm/hardware/cache-l2x0.h>
 
-#include "clock.h"
 #include "cpu-8815.h"
 
-#define __MEM_4K_RESOURCE(x) \
-	.res = {.start = (x), .end = (x) + SZ_4K - 1, .flags = IORESOURCE_MEM}
-
 /* The 8815 has 4 GPIO blocks, let's register them immediately */
-
-#define GPIO_RESOURCE(block)						\
-	{								\
-		.start	= NOMADIK_GPIO##block##_BASE,			\
-		.end	= NOMADIK_GPIO##block##_BASE + SZ_4K - 1,	\
-		.flags	= IORESOURCE_MEM,				\
-	},								\
-	{								\
-		.start	= IRQ_GPIO##block,				\
-		.end	= IRQ_GPIO##block,				\
-		.flags	= IORESOURCE_IRQ,				\
-	}
-
-#define GPIO_DEVICE(block)						\
-	{								\
-		.name 		= "gpio",				\
-		.id		= block,				\
-		.num_resources 	= 2,					\
-		.resource	= &cpu8815_gpio_resources[block * 2],	\
-		.dev = {						\
-			.platform_data = &cpu8815_gpio[block],		\
-		},							\
-	}
-
-static struct nmk_gpio_platform_data cpu8815_gpio[] = {
-	{
-		.name = "GPIO-0-31",
-		.first_gpio = 0,
-		.first_irq = NOMADIK_GPIO_TO_IRQ(0),
-	}, {
-		.name = "GPIO-32-63",
-		.first_gpio = 32,
-		.first_irq = NOMADIK_GPIO_TO_IRQ(32),
-	}, {
-		.name = "GPIO-64-95",
-		.first_gpio = 64,
-		.first_irq = NOMADIK_GPIO_TO_IRQ(64),
-	}, {
-		.name = "GPIO-96-127", /* 124..127 not routed to pin */
-		.first_gpio = 96,
-		.first_irq = NOMADIK_GPIO_TO_IRQ(96),
-	}
+static resource_size_t __initdata cpu8815_gpio_base[] = {
+	NOMADIK_GPIO0_BASE,
+	NOMADIK_GPIO1_BASE,
+	NOMADIK_GPIO2_BASE,
+	NOMADIK_GPIO3_BASE,
 };
 
-static struct resource cpu8815_gpio_resources[] = {
-	GPIO_RESOURCE(0),
-	GPIO_RESOURCE(1),
-	GPIO_RESOURCE(2),
-	GPIO_RESOURCE(3),
-};
-
-static struct platform_device cpu8815_platform_gpio[] = {
-	GPIO_DEVICE(0),
-	GPIO_DEVICE(1),
-	GPIO_DEVICE(2),
-	GPIO_DEVICE(3),
-};
+static struct platform_device *
+cpu8815_add_gpio(int id, resource_size_t addr, int irq,
+		 struct nmk_gpio_platform_data *pdata)
+{
+	struct resource resources[] = {
+		{
+			.start	= addr,
+			.end	= addr + 127,
+			.flags	= IORESOURCE_MEM,
+		},
+		{
+			.start	= irq,
+			.end	= irq,
+			.flags	= IORESOURCE_IRQ,
+		}
+	};
+
+	return platform_device_register_resndata(NULL, "gpio", id,
+				resources, ARRAY_SIZE(resources),
+				pdata, sizeof(*pdata));
+}
 
-static AMBA_APB_DEVICE(cpu8815_amba_rng, "rng", 0, NOMADIK_RNG_BASE, { }, NULL);
+void cpu8815_add_gpios(resource_size_t *base, int num, int irq,
+		       struct nmk_gpio_platform_data *pdata)
+{
+	int first = 0;
+	int i;
 
-static struct platform_device *platform_devs[] __initdata = {
-	cpu8815_platform_gpio + 0,
-	cpu8815_platform_gpio + 1,
-	cpu8815_platform_gpio + 2,
-	cpu8815_platform_gpio + 3,
-};
+	for (i = 0; i < num; i++, first += 32, irq++) {
+		pdata->first_gpio = first;
+		pdata->first_irq = NOMADIK_GPIO_TO_IRQ(first);
+		pdata->num_gpio = 32;
 
-static struct amba_device *amba_devs[] __initdata = {
-	&cpu8815_amba_rng_device
-};
+		cpu8815_add_gpio(i, base[i], irq, pdata);
+	}
+}
 
 static int __init cpu8815_init(void)
 {
-	int i;
-
-	platform_add_devices(platform_devs, ARRAY_SIZE(platform_devs));
-	for (i = 0; i < ARRAY_SIZE(amba_devs); i++)
-		amba_device_register(amba_devs[i], &iomem_resource);
+	struct nmk_gpio_platform_data pdata = {
+		/* No custom data yet */
+	};
+
+	cpu8815_add_gpios(cpu8815_gpio_base, ARRAY_SIZE(cpu8815_gpio_base),
+			  IRQ_GPIO0, &pdata);
+	amba_apb_device_add(NULL, "rng", NOMADIK_RNG_BASE, SZ_4K, 0, 0, NULL, 0);
+	amba_apb_device_add(NULL, "rtc-pl031", NOMADIK_RTC_BASE, SZ_4K, IRQ_RTC_RTT, 0, NULL, 0);
 	return 0;
 }
 arch_initcall(cpu8815_init);
@@ -147,7 +123,7 @@ void __init cpu8815_init_irq(void)
 	 * Init clocks here so that they are available for system timer
 	 * initialization.
 	 */
-	clk_init();
+	nomadik_clk_init();
 }
 
 /*

arch/arm/mach-nomadik/i2c-8815nhk.c

@@ -5,6 +5,7 @@
 #include <linux/i2c-gpio.h>
 #include <linux/platform_device.h>
 #include <plat/gpio-nomadik.h>
+#include <plat/pincfg.h>
 
 /*
  * There are two busses in the 8815NHK.
@@ -12,19 +13,27 @@
  * use bit-bang through GPIO by now, to keep things simple
  */
 
+/* I2C0 connected to the STw4811 power management chip */
 static struct i2c_gpio_platform_data nhk8815_i2c_data0 = {
 	/* keep defaults for timeouts; pins are push-pull bidirectional */
 	.scl_pin = 62,
 	.sda_pin = 63,
 };
 
+/* I2C1 connected to various sensors */
 static struct i2c_gpio_platform_data nhk8815_i2c_data1 = {
 	/* keep defaults for timeouts; pins are push-pull bidirectional */
 	.scl_pin = 53,
 	.sda_pin = 54,
 };
 
-/* first bus: GPIO XX and YY */
+/* I2C2 connected to the USB portions of the STw4811 only */
+static struct i2c_gpio_platform_data nhk8815_i2c_data2 = {
+	/* keep defaults for timeouts; pins are push-pull bidirectional */
+	.scl_pin = 73,
+	.sda_pin = 74,
+};
+
 static struct platform_device nhk8815_i2c_dev0 = {
 	.name	= "i2c-gpio",
 	.id	= 0,
@@ -32,7 +41,7 @@ static struct platform_device nhk8815_i2c_dev0 = {
 		.platform_data = &nhk8815_i2c_data0,
 	},
 };
-/* second bus: GPIO XX and YY */
+
 static struct platform_device nhk8815_i2c_dev1 = {
 	.name	= "i2c-gpio",
 	.id	= 1,
@@ -41,15 +50,29 @@ static struct platform_device nhk8815_i2c_dev1 = {
 	},
 };
 
+static struct platform_device nhk8815_i2c_dev2 = {
+	.name	= "i2c-gpio",
+	.id	= 2,
+	.dev	= {
+		.platform_data = &nhk8815_i2c_data2,
+	},
+};
+
+static pin_cfg_t cpu8815_pins_i2c[] = {
+	PIN_CFG_INPUT(62, GPIO, PULLUP),
+	PIN_CFG_INPUT(63, GPIO, PULLUP),
+	PIN_CFG_INPUT(53, GPIO, PULLUP),
+	PIN_CFG_INPUT(54, GPIO, PULLUP),
+	PIN_CFG_INPUT(73, GPIO, PULLUP),
+	PIN_CFG_INPUT(74, GPIO, PULLUP),
+};
+
 static int __init nhk8815_i2c_init(void)
 {
-	nmk_gpio_set_mode(nhk8815_i2c_data0.scl_pin, NMK_GPIO_ALT_GPIO);
-	nmk_gpio_set_mode(nhk8815_i2c_data0.sda_pin, NMK_GPIO_ALT_GPIO);
+	nmk_config_pins(cpu8815_pins_i2c, ARRAY_SIZE(cpu8815_pins_i2c));
 	platform_device_register(&nhk8815_i2c_dev0);
-
-	nmk_gpio_set_mode(nhk8815_i2c_data1.scl_pin, NMK_GPIO_ALT_GPIO);
-	nmk_gpio_set_mode(nhk8815_i2c_data1.sda_pin, NMK_GPIO_ALT_GPIO);
 	platform_device_register(&nhk8815_i2c_dev1);
+	platform_device_register(&nhk8815_i2c_dev2);
 
 	return 0;
 }
@@ -58,6 +81,7 @@ static void __exit nhk8815_i2c_exit(void)
 {
 	platform_device_unregister(&nhk8815_i2c_dev0);
 	platform_device_unregister(&nhk8815_i2c_dev1);
+	platform_device_unregister(&nhk8815_i2c_dev2);
 	return;
 }
 

arch/arm/mach-nomadik/include/mach/irqs.h

@@ -22,56 +22,56 @@
 
 #include <mach/hardware.h>
 
-#define IRQ_VIC_START		0	/* first VIC interrupt is 0 */
+#define IRQ_VIC_START		1	/* first VIC interrupt is 1 */
 
 /*
  * Interrupt numbers generic for all Nomadik Chip cuts
  */
-#define IRQ_WATCHDOG			0
-#define IRQ_SOFTINT			1
-#define IRQ_CRYPTO			2
-#define IRQ_OWM				3
-#define IRQ_MTU0			4
-#define IRQ_MTU1			5
-#define IRQ_GPIO0			6
-#define IRQ_GPIO1			7
-#define IRQ_GPIO2			8
-#define IRQ_GPIO3			9
-#define IRQ_RTC_RTT			10
-#define IRQ_SSP				11
-#define IRQ_UART0			12
-#define IRQ_DMA1			13
-#define IRQ_CLCD_MDIF			14
-#define IRQ_DMA0			15
-#define IRQ_PWRFAIL			16
-#define IRQ_UART1			17
-#define IRQ_FIRDA			18
-#define IRQ_MSP0			19
-#define IRQ_I2C0			20
-#define IRQ_I2C1			21
-#define IRQ_SDMMC			22
-#define IRQ_USBOTG			23
-#define IRQ_SVA_IT0			24
-#define IRQ_SVA_IT1			25
-#define IRQ_SAA_IT0			26
-#define IRQ_SAA_IT1			27
-#define IRQ_UART2			28
-#define IRQ_MSP2			31
-#define IRQ_L2CC			48
-#define IRQ_HPI				49
-#define IRQ_SKE				50
-#define IRQ_KP				51
-#define IRQ_MEMST			54
-#define IRQ_SGA_IT			58
-#define IRQ_USBM			60
-#define IRQ_MSP1			62
+#define IRQ_WATCHDOG			1
+#define IRQ_SOFTINT			2
+#define IRQ_CRYPTO			3
+#define IRQ_OWM				4
+#define IRQ_MTU0			5
+#define IRQ_MTU1			6
+#define IRQ_GPIO0			7
+#define IRQ_GPIO1			8
+#define IRQ_GPIO2			9
+#define IRQ_GPIO3			10
+#define IRQ_RTC_RTT			11
+#define IRQ_SSP				12
+#define IRQ_UART0			13
+#define IRQ_DMA1			14
+#define IRQ_CLCD_MDIF			15
+#define IRQ_DMA0			16
+#define IRQ_PWRFAIL			17
+#define IRQ_UART1			18
+#define IRQ_FIRDA			19
+#define IRQ_MSP0			20
+#define IRQ_I2C0			21
+#define IRQ_I2C1			22
+#define IRQ_SDMMC			23
+#define IRQ_USBOTG			24
+#define IRQ_SVA_IT0			25
+#define IRQ_SVA_IT1			26
+#define IRQ_SAA_IT0			27
+#define IRQ_SAA_IT1			28
+#define IRQ_UART2			29
+#define IRQ_MSP2			30
+#define IRQ_L2CC			49
+#define IRQ_HPI				50
+#define IRQ_SKE				51
+#define IRQ_KP				52
+#define IRQ_MEMST			55
+#define IRQ_SGA_IT			59
+#define IRQ_USBM			61
+#define IRQ_MSP1			63
 
-#define NOMADIK_SOC_NR_IRQS		64
+#define NOMADIK_GPIO_OFFSET		(IRQ_VIC_START+64)
 
 /* After chip-specific IRQ numbers we have the GPIO ones */
 #define NOMADIK_NR_GPIO			128 /* last 4 not wired to pins */
-#define NOMADIK_GPIO_TO_IRQ(gpio)	((gpio) + NOMADIK_SOC_NR_IRQS)
-#define NOMADIK_IRQ_TO_GPIO(irq)	((irq) - NOMADIK_SOC_NR_IRQS)
+#define NOMADIK_GPIO_TO_IRQ(gpio)	((gpio) + NOMADIK_GPIO_OFFSET)
+#define NOMADIK_IRQ_TO_GPIO(irq)	((irq) - NOMADIK_GPIO_OFFSET)
 #define NR_IRQS				NOMADIK_GPIO_TO_IRQ(NOMADIK_NR_GPIO)
 
 /* Following two are used by entry_macro.S, to access our dual-vic */
@@ -79,4 +79,3 @@
 #define VIC_REG_IRQSR1		0x20
 
 #endif /* __ASM_ARCH_IRQS_H */
-

arch/arm/mach-omap2/Makefile

@@ -93,6 +93,7 @@ obj-$(CONFIG_ARCH_OMAP3)		+= vc3xxx_data.o vp3xxx_data.o
 obj-$(CONFIG_ARCH_OMAP4)		+= prcm.o cminst44xx.o cm44xx.o
 obj-$(CONFIG_ARCH_OMAP4)		+= prcm_mpu44xx.o prminst44xx.o
 obj-$(CONFIG_ARCH_OMAP4)		+= vc44xx_data.o vp44xx_data.o prm44xx.o
+obj-$(CONFIG_SOC_AM33XX)		+= prcm.o prm33xx.o cm33xx.o
 
 # OMAP voltage domains
 voltagedomain-common			:= voltage.o vc.o vp.o
@@ -102,6 +103,7 @@ obj-$(CONFIG_ARCH_OMAP3)		+= $(voltagedomain-common)
 obj-$(CONFIG_ARCH_OMAP3)		+= voltagedomains3xxx_data.o
 obj-$(CONFIG_ARCH_OMAP4)		+= $(voltagedomain-common)
 obj-$(CONFIG_ARCH_OMAP4)		+= voltagedomains44xx_data.o
+obj-$(CONFIG_SOC_AM33XX)                += voltagedomains33xx_data.o
 
 # OMAP powerdomain framework
 powerdomain-common			+= powerdomain.o powerdomain-common.o
@@ -116,6 +118,8 @@ obj-$(CONFIG_ARCH_OMAP3)		+= powerdomains2xxx_3xxx_data.o
 obj-$(CONFIG_ARCH_OMAP4)		+= $(powerdomain-common)
 obj-$(CONFIG_ARCH_OMAP4)		+= powerdomain44xx.o
 obj-$(CONFIG_ARCH_OMAP4)		+= powerdomains44xx_data.o
+obj-$(CONFIG_SOC_AM33XX)		+= powerdomain33xx.o
+obj-$(CONFIG_SOC_AM33XX)		+= powerdomains33xx_data.o
 
 # PRCM clockdomain control
 clockdomain-common			+= clockdomain.o
@@ -131,6 +135,8 @@ obj-$(CONFIG_ARCH_OMAP3)		+= clockdomains3xxx_data.o
 obj-$(CONFIG_ARCH_OMAP4)		+= $(clockdomain-common)
 obj-$(CONFIG_ARCH_OMAP4)		+= clockdomain44xx.o
 obj-$(CONFIG_ARCH_OMAP4)		+= clockdomains44xx_data.o
+obj-$(CONFIG_SOC_AM33XX)		+= clockdomain33xx.o
+obj-$(CONFIG_SOC_AM33XX)		+= clockdomains33xx_data.o
 
 # Clock framework
 obj-$(CONFIG_ARCH_OMAP2)		+= $(clock-common) clock2xxx.o

arch/arm/mach-omap2/board-generic.c

@@ -112,6 +112,24 @@ DT_MACHINE_START(OMAP3_DT, "Generic OMAP3 (Flattened Device Tree)")
 MACHINE_END
 #endif
 
+#ifdef CONFIG_SOC_AM33XX
+static const char *am33xx_boards_compat[] __initdata = {
+	"ti,am33xx",
+	NULL,
+};
+
+DT_MACHINE_START(AM33XX_DT, "Generic AM33XX (Flattened Device Tree)")
+	.reserve	= omap_reserve,
+	.map_io		= am33xx_map_io,
+	.init_early	= am33xx_init_early,
+	.init_irq	= omap_init_irq,
+	.handle_irq	= omap3_intc_handle_irq,
+	.init_machine	= omap_generic_init,
+	.timer		= &omap3_am33xx_timer,
+	.dt_compat	= am33xx_boards_compat,
+MACHINE_END
+#endif
+
 #ifdef CONFIG_ARCH_OMAP4
 static const char *omap4_boards_compat[] __initdata = {
 	"ti,omap4",

arch/arm/mach-omap2/clockdomain.h

@@ -199,6 +199,7 @@ int clkdm_hwmod_disable(struct clockdomain *clkdm, struct omap_hwmod *oh);
 extern void __init omap242x_clockdomains_init(void);
 extern void __init omap243x_clockdomains_init(void);
 extern void __init omap3xxx_clockdomains_init(void);
+extern void __init am33xx_clockdomains_init(void);
 extern void __init omap44xx_clockdomains_init(void);
 extern void _clkdm_add_autodeps(struct clockdomain *clkdm);
 extern void _clkdm_del_autodeps(struct clockdomain *clkdm);
@@ -206,6 +207,7 @@ extern void _clkdm_del_autodeps(struct clockdomain *clkdm);
 extern struct clkdm_ops omap2_clkdm_operations;
 extern struct clkdm_ops omap3_clkdm_operations;
 extern struct clkdm_ops omap4_clkdm_operations;
+extern struct clkdm_ops am33xx_clkdm_operations;
 
 extern struct clkdm_dep gfx_24xx_wkdeps[];
 extern struct clkdm_dep dsp_24xx_wkdeps[];

arch/arm/mach-omap2/clockdomain33xx.c

+/*
+ * AM33XX clockdomain control
+ *
+ * Copyright (C) 2011-2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Vaibhav Hiremath <hvaibhav@ti.com>
+ *
+ * Derived from mach-omap2/clockdomain44xx.c written by Rajendra Nayak
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/kernel.h>
+
+#include "clockdomain.h"
+#include "cm33xx.h"
+
+
+static int am33xx_clkdm_sleep(struct clockdomain *clkdm)
+{
+	am33xx_cm_clkdm_force_sleep(clkdm->cm_inst, clkdm->clkdm_offs);
+	return 0;
+}
+
+static int am33xx_clkdm_wakeup(struct clockdomain *clkdm)
+{
+	am33xx_cm_clkdm_force_wakeup(clkdm->cm_inst, clkdm->clkdm_offs);
+	return 0;
+}
+
+static void am33xx_clkdm_allow_idle(struct clockdomain *clkdm)
+{
+	am33xx_cm_clkdm_enable_hwsup(clkdm->cm_inst, clkdm->clkdm_offs);
+}
+
+static void am33xx_clkdm_deny_idle(struct clockdomain *clkdm)
+{
+	am33xx_cm_clkdm_disable_hwsup(clkdm->cm_inst, clkdm->clkdm_offs);
+}
+
+static int am33xx_clkdm_clk_enable(struct clockdomain *clkdm)
+{
+	if (clkdm->flags & CLKDM_CAN_FORCE_WAKEUP)
+		return am33xx_clkdm_wakeup(clkdm);
+
+	return 0;
+}
+
+static int am33xx_clkdm_clk_disable(struct clockdomain *clkdm)
+{
+	bool hwsup = false;
+
+	hwsup = am33xx_cm_is_clkdm_in_hwsup(clkdm->cm_inst, clkdm->clkdm_offs);
+
+	if (!hwsup && (clkdm->flags & CLKDM_CAN_FORCE_SLEEP))
+		am33xx_clkdm_sleep(clkdm);
+
+	return 0;
+}
+
+struct clkdm_ops am33xx_clkdm_operations = {
+	.clkdm_sleep		= am33xx_clkdm_sleep,
+	.clkdm_wakeup		= am33xx_clkdm_wakeup,
+	.clkdm_allow_idle	= am33xx_clkdm_allow_idle,
+	.clkdm_deny_idle	= am33xx_clkdm_deny_idle,
+	.clkdm_clk_enable	= am33xx_clkdm_clk_enable,
+	.clkdm_clk_disable	= am33xx_clkdm_clk_disable,
+};

arch/arm/mach-omap2/clockdomains33xx_data.c

+/*
+ * AM33XX Clock Domain data.
+ *
+ * Copyright (C) 2011-2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Vaibhav Hiremath <hvaibhav@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/kernel.h>
+#include <linux/io.h>
+
+#include "clockdomain.h"
+#include "cm.h"
+#include "cm33xx.h"
+#include "cm-regbits-33xx.h"
+
+static struct clockdomain l4ls_am33xx_clkdm = {
+	.name		= "l4ls_clkdm",
+	.pwrdm		= { .name = "per_pwrdm" },
+	.cm_inst	= AM33XX_CM_PER_MOD,
+	.clkdm_offs	= AM33XX_CM_PER_L4LS_CLKSTCTRL_OFFSET,
+	.flags		= CLKDM_CAN_SWSUP,
+};
+
+static struct clockdomain l3s_am33xx_clkdm = {
+	.name		= "l3s_clkdm",
+	.pwrdm		= { .name = "per_pwrdm" },
+	.cm_inst	= AM33XX_CM_PER_MOD,
+	.clkdm_offs	= AM33XX_CM_PER_L3S_CLKSTCTRL_OFFSET,
+	.flags		= CLKDM_CAN_SWSUP,
+};
+
+static struct clockdomain l4fw_am33xx_clkdm = {
+	.name		= "l4fw_clkdm",
+	.pwrdm		= { .name = "per_pwrdm" },
+	.cm_inst	= AM33XX_CM_PER_MOD,
+	.clkdm_offs	= AM33XX_CM_PER_L4FW_CLKSTCTRL_OFFSET,
+	.flags		= CLKDM_CAN_SWSUP,
+};
+
+static struct clockdomain l3_am33xx_clkdm = {
+	.name		= "l3_clkdm",
+	.pwrdm		= { .name = "per_pwrdm" },
+	.cm_inst	= AM33XX_CM_PER_MOD,
+	.clkdm_offs	= AM33XX_CM_PER_L3_CLKSTCTRL_OFFSET,
+	.flags		= CLKDM_CAN_SWSUP,
+};
+
+static struct clockdomain l4hs_am33xx_clkdm = {
+	.name		= "l4hs_clkdm",
+	.pwrdm		= { .name = "per_pwrdm" },
+	.cm_inst	= AM33XX_CM_PER_MOD,
+	.clkdm_offs	= AM33XX_CM_PER_L4HS_CLKSTCTRL_OFFSET,
+	.flags		= CLKDM_CAN_SWSUP,
+};
+
+static struct clockdomain ocpwp_l3_am33xx_clkdm = {
+	.name		= "ocpwp_l3_clkdm",
+	.pwrdm		= { .name = "per_pwrdm" },
+	.cm_inst	= AM33XX_CM_PER_MOD,
+	.clkdm_offs	= AM33XX_CM_PER_OCPWP_L3_CLKSTCTRL_OFFSET,
+	.flags		= CLKDM_CAN_SWSUP,
+};
+
+static struct clockdomain pruss_ocp_am33xx_clkdm = {
+	.name		= "pruss_ocp_clkdm",
+	.pwrdm		= { .name = "per_pwrdm" },
+	.cm_inst	= AM33XX_CM_PER_MOD,
+	.clkdm_offs	= AM33XX_CM_PER_PRUSS_CLKSTCTRL_OFFSET,
+	.flags		= CLKDM_CAN_SWSUP,
+};
+
+static struct clockdomain cpsw_125mhz_am33xx_clkdm = {
+	.name		= "cpsw_125mhz_clkdm",
+	.pwrdm		= { .name = "per_pwrdm" },
+	.cm_inst	= AM33XX_CM_PER_MOD,
+	.clkdm_offs	= AM33XX_CM_PER_CPSW_CLKSTCTRL_OFFSET,
+	.flags		= CLKDM_CAN_SWSUP,
+};
+
+static struct clockdomain lcdc_am33xx_clkdm = {
+	.name		= "lcdc_clkdm",
+	.pwrdm		= { .name = "per_pwrdm" },
+	.cm_inst	= AM33XX_CM_PER_MOD,
+	.clkdm_offs	= AM33XX_CM_PER_LCDC_CLKSTCTRL_OFFSET,
+	.flags		= CLKDM_CAN_SWSUP,
+};
+
+static struct clockdomain clk_24mhz_am33xx_clkdm = {
+	.name		= "clk_24mhz_clkdm",
+	.pwrdm		= { .name = "per_pwrdm" },
+	.cm_inst	= AM33XX_CM_PER_MOD,
+	.clkdm_offs	= AM33XX_CM_PER_CLK_24MHZ_CLKSTCTRL_OFFSET,
+	.flags		= CLKDM_CAN_SWSUP,
+};
+
+static struct clockdomain l4_wkup_am33xx_clkdm = {
+	.name		= "l4_wkup_clkdm",
+	.pwrdm		= { .name = "wkup_pwrdm" },
+	.cm_inst	= AM33XX_CM_WKUP_MOD,
+	.clkdm_offs	= AM33XX_CM_WKUP_CLKSTCTRL_OFFSET,
+	.flags		= CLKDM_CAN_SWSUP,
+};
+
+static struct clockdomain l3_aon_am33xx_clkdm = {
+	.name		= "l3_aon_clkdm",
+	.pwrdm		= { .name = "wkup_pwrdm" },
+	.cm_inst	= AM33XX_CM_WKUP_MOD,
+	.clkdm_offs	= AM33XX_CM_L3_AON_CLKSTCTRL_OFFSET,
+	.flags		= CLKDM_CAN_SWSUP,
+};
+
+static struct clockdomain l4_wkup_aon_am33xx_clkdm = {
+	.name		= "l4_wkup_aon_clkdm",
+	.pwrdm		= { .name = "wkup_pwrdm" },
+	.cm_inst	= AM33XX_CM_WKUP_MOD,
+	.clkdm_offs	= AM33XX_CM_L4_WKUP_AON_CLKSTCTRL_OFFSET,
+	.flags		= CLKDM_CAN_SWSUP,
+};
+
+static struct clockdomain mpu_am33xx_clkdm = {
+	.name		= "mpu_clkdm",
+	.pwrdm		= { .name = "mpu_pwrdm" },
+	.cm_inst	= AM33XX_CM_MPU_MOD,
+	.clkdm_offs	= AM33XX_CM_MPU_CLKSTCTRL_OFFSET,
+	.flags		= CLKDM_CAN_SWSUP,
+};
+
+static struct clockdomain l4_rtc_am33xx_clkdm = {
+	.name		= "l4_rtc_clkdm",
+	.pwrdm		= { .name = "rtc_pwrdm" },
+	.cm_inst	= AM33XX_CM_RTC_MOD,
+	.clkdm_offs	= AM33XX_CM_RTC_CLKSTCTRL_OFFSET,
+	.flags		= CLKDM_CAN_SWSUP,
+};
+
+static struct clockdomain gfx_l3_am33xx_clkdm = {
+	.name		= "gfx_l3_clkdm",
+	.pwrdm		= { .name = "gfx_pwrdm" },
+	.cm_inst	= AM33XX_CM_GFX_MOD,
+	.clkdm_offs	= AM33XX_CM_GFX_L3_CLKSTCTRL_OFFSET,
+	.flags		= CLKDM_CAN_SWSUP,
+};
+
+static struct clockdomain gfx_l4ls_gfx_am33xx_clkdm = {
+	.name		= "gfx_l4ls_gfx_clkdm",
+	.pwrdm		= { .name = "gfx_pwrdm" },
+	.cm_inst	= AM33XX_CM_GFX_MOD,
+	.clkdm_offs	= AM33XX_CM_GFX_L4LS_GFX_CLKSTCTRL__1_OFFSET,
+	.flags		= CLKDM_CAN_SWSUP,
+};
+
+static struct clockdomain l4_cefuse_am33xx_clkdm = {
+	.name		= "l4_cefuse_clkdm",
+	.pwrdm		= { .name = "cefuse_pwrdm" },
+	.cm_inst	= AM33XX_CM_CEFUSE_MOD,
+	.clkdm_offs	= AM33XX_CM_CEFUSE_CLKSTCTRL_OFFSET,
+	.flags		= CLKDM_CAN_SWSUP,
+};
+
+static struct clockdomain *clockdomains_am33xx[] __initdata = {
+	&l4ls_am33xx_clkdm,
+	&l3s_am33xx_clkdm,
+	&l4fw_am33xx_clkdm,
+	&l3_am33xx_clkdm,
+	&l4hs_am33xx_clkdm,
+	&ocpwp_l3_am33xx_clkdm,
+	&pruss_ocp_am33xx_clkdm,
+	&cpsw_125mhz_am33xx_clkdm,
+	&lcdc_am33xx_clkdm,
+	&clk_24mhz_am33xx_clkdm,
+	&l4_wkup_am33xx_clkdm,
+	&l3_aon_am33xx_clkdm,
+	&l4_wkup_aon_am33xx_clkdm,
+	&mpu_am33xx_clkdm,
+	&l4_rtc_am33xx_clkdm,
+	&gfx_l3_am33xx_clkdm,
+	&gfx_l4ls_gfx_am33xx_clkdm,
+	&l4_cefuse_am33xx_clkdm,
+	NULL,
+};
+
+void __init am33xx_clockdomains_init(void)
+{
+	clkdm_register_platform_funcs(&am33xx_clkdm_operations);
+	clkdm_register_clkdms(clockdomains_am33xx);
+	clkdm_complete_init();
+}

arch/arm/mach-omap2/cm33xx.c

+/*
+ * AM33XX CM functions
+ *
+ * Copyright (C) 2011-2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Vaibhav Hiremath <hvaibhav@ti.com>
+ *
+ * Reference taken from from OMAP4 cminst44xx.c
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/errno.h>
+#include <linux/err.h>
+#include <linux/io.h>
+
+#include <plat/common.h>
+
+#include "cm.h"
+#include "cm33xx.h"
+#include "cm-regbits-34xx.h"
+#include "cm-regbits-33xx.h"
+#include "prm33xx.h"
+
+/*
+ * CLKCTRL_IDLEST_*: possible values for the CM_*_CLKCTRL.IDLEST bitfield:
+ *
+ *   0x0 func:     Module is fully functional, including OCP
+ *   0x1 trans:    Module is performing transition: wakeup, or sleep, or sleep
+ *                 abortion
+ *   0x2 idle:     Module is in Idle mode (only OCP part). It is functional if
+ *                 using separate functional clock
+ *   0x3 disabled: Module is disabled and cannot be accessed
+ *
+ */
+#define CLKCTRL_IDLEST_FUNCTIONAL		0x0
+#define CLKCTRL_IDLEST_INTRANSITION		0x1
+#define CLKCTRL_IDLEST_INTERFACE_IDLE		0x2
+#define CLKCTRL_IDLEST_DISABLED			0x3
+
+/* Private functions */
+
+/* Read a register in a CM instance */
+static inline u32 am33xx_cm_read_reg(s16 inst, u16 idx)
+{
+	return __raw_readl(cm_base + inst + idx);
+}
+
+/* Write into a register in a CM */
+static inline void am33xx_cm_write_reg(u32 val, s16 inst, u16 idx)
+{
+	__raw_writel(val, cm_base + inst + idx);
+}
+
+/* Read-modify-write a register in CM */
+static inline u32 am33xx_cm_rmw_reg_bits(u32 mask, u32 bits, s16 inst, s16 idx)
+{
+	u32 v;
+
+	v = am33xx_cm_read_reg(inst, idx);
+	v &= ~mask;
+	v |= bits;
+	am33xx_cm_write_reg(v, inst, idx);
+
+	return v;
+}
+
+static inline u32 am33xx_cm_set_reg_bits(u32 bits, s16 inst, s16 idx)
+{
+	return am33xx_cm_rmw_reg_bits(bits, bits, inst, idx);
+}
+
+static inline u32 am33xx_cm_clear_reg_bits(u32 bits, s16 inst, s16 idx)
+{
+	return am33xx_cm_rmw_reg_bits(bits, 0x0, inst, idx);
+}
+
+static inline u32 am33xx_cm_read_reg_bits(u16 inst, s16 idx, u32 mask)
+{
+	u32 v;
+
+	v = am33xx_cm_read_reg(inst, idx);
+	v &= mask;
+	v >>= __ffs(mask);
+
+	return v;
+}
+
+/**
+ * _clkctrl_idlest - read a CM_*_CLKCTRL register; mask & shift IDLEST bitfield
+ * @inst: CM instance register offset (*_INST macro)
+ * @cdoffs: Clockdomain register offset (*_CDOFFS macro)
+ * @clkctrl_offs: Module clock control register offset (*_CLKCTRL macro)
+ *
+ * Return the IDLEST bitfield of a CM_*_CLKCTRL register, shifted down to
+ * bit 0.
+ */
+static u32 _clkctrl_idlest(u16 inst, s16 cdoffs, u16 clkctrl_offs)
+{
+	u32 v = am33xx_cm_read_reg(inst, clkctrl_offs);
+	v &= AM33XX_IDLEST_MASK;
+	v >>= AM33XX_IDLEST_SHIFT;
+	return v;
+}
+
+/**
+ * _is_module_ready - can module registers be accessed without causing an abort?
+ * @inst: CM instance register offset (*_INST macro)
+ * @cdoffs: Clockdomain register offset (*_CDOFFS macro)
+ * @clkctrl_offs: Module clock control register offset (*_CLKCTRL macro)
+ *
+ * Returns true if the module's CM_*_CLKCTRL.IDLEST bitfield is either
+ * *FUNCTIONAL or *INTERFACE_IDLE; false otherwise.
+ */
+static bool _is_module_ready(u16 inst, s16 cdoffs, u16 clkctrl_offs)
+{
+	u32 v;
+
+	v = _clkctrl_idlest(inst, cdoffs, clkctrl_offs);
+
+	return (v == CLKCTRL_IDLEST_FUNCTIONAL ||
+		v == CLKCTRL_IDLEST_INTERFACE_IDLE) ? true : false;
+}
+
+/**
+ * _clktrctrl_write - write @c to a CM_CLKSTCTRL.CLKTRCTRL register bitfield
+ * @c: CLKTRCTRL register bitfield (LSB = bit 0, i.e., unshifted)
+ * @inst: CM instance register offset (*_INST macro)
+ * @cdoffs: Clockdomain register offset (*_CDOFFS macro)
+ *
+ * @c must be the unshifted value for CLKTRCTRL - i.e., this function
+ * will handle the shift itself.
+ */
+static void _clktrctrl_write(u8 c, s16 inst, u16 cdoffs)
+{
+	u32 v;
+
+	v = am33xx_cm_read_reg(inst, cdoffs);
+	v &= ~AM33XX_CLKTRCTRL_MASK;
+	v |= c << AM33XX_CLKTRCTRL_SHIFT;
+	am33xx_cm_write_reg(v, inst, cdoffs);
+}
+
+/* Public functions */
+
+/**
+ * am33xx_cm_is_clkdm_in_hwsup - is a clockdomain in hwsup idle mode?
+ * @inst: CM instance register offset (*_INST macro)
+ * @cdoffs: Clockdomain register offset (*_CDOFFS macro)
+ *
+ * Returns true if the clockdomain referred to by (@inst, @cdoffs)
+ * is in hardware-supervised idle mode, or 0 otherwise.
+ */
+bool am33xx_cm_is_clkdm_in_hwsup(s16 inst, u16 cdoffs)
+{
+	u32 v;
+
+	v = am33xx_cm_read_reg(inst, cdoffs);
+	v &= AM33XX_CLKTRCTRL_MASK;
+	v >>= AM33XX_CLKTRCTRL_SHIFT;
+
+	return (v == OMAP34XX_CLKSTCTRL_ENABLE_AUTO) ? true : false;
+}
+
+/**
+ * am33xx_cm_clkdm_enable_hwsup - put a clockdomain in hwsup-idle mode
+ * @inst: CM instance register offset (*_INST macro)
+ * @cdoffs: Clockdomain register offset (*_CDOFFS macro)
+ *
+ * Put a clockdomain referred to by (@inst, @cdoffs) into
+ * hardware-supervised idle mode.  No return value.
+ */
+void am33xx_cm_clkdm_enable_hwsup(s16 inst, u16 cdoffs)
+{
+	_clktrctrl_write(OMAP34XX_CLKSTCTRL_ENABLE_AUTO, inst, cdoffs);
+}
+
+/**
+ * am33xx_cm_clkdm_disable_hwsup - put a clockdomain in swsup-idle mode
+ * @inst: CM instance register offset (*_INST macro)
+ * @cdoffs: Clockdomain register offset (*_CDOFFS macro)
+ *
+ * Put a clockdomain referred to by (@inst, @cdoffs) into
+ * software-supervised idle mode, i.e., controlled manually by the
+ * Linux OMAP clockdomain code.  No return value.
+ */
+void am33xx_cm_clkdm_disable_hwsup(s16 inst, u16 cdoffs)
+{
+	_clktrctrl_write(OMAP34XX_CLKSTCTRL_DISABLE_AUTO, inst, cdoffs);
+}
+
+/**
+ * am33xx_cm_clkdm_force_sleep - try to put a clockdomain into idle
+ * @inst: CM instance register offset (*_INST macro)
+ * @cdoffs: Clockdomain register offset (*_CDOFFS macro)
+ *
+ * Put a clockdomain referred to by (@inst, @cdoffs) into idle
+ * No return value.
+ */
+void am33xx_cm_clkdm_force_sleep(s16 inst, u16 cdoffs)
+{
+	_clktrctrl_write(OMAP34XX_CLKSTCTRL_FORCE_SLEEP, inst, cdoffs);
+}
+
+/**
+ * am33xx_cm_clkdm_force_wakeup - try to take a clockdomain out of idle
+ * @inst: CM instance register offset (*_INST macro)
+ * @cdoffs: Clockdomain register offset (*_CDOFFS macro)
+ *
+ * Take a clockdomain referred to by (@inst, @cdoffs) out of idle,
+ * waking it up.  No return value.
+ */
+void am33xx_cm_clkdm_force_wakeup(s16 inst, u16 cdoffs)
+{
+	_clktrctrl_write(OMAP34XX_CLKSTCTRL_FORCE_WAKEUP, inst, cdoffs);
+}
+
+/*
+ *
+ */
+
+/**
+ * am33xx_cm_wait_module_ready - wait for a module to be in 'func' state
+ * @inst: CM instance register offset (*_INST macro)
+ * @cdoffs: Clockdomain register offset (*_CDOFFS macro)
+ * @clkctrl_offs: Module clock control register offset (*_CLKCTRL macro)
+ *
+ * Wait for the module IDLEST to be functional. If the idle state is in any
+ * the non functional state (trans, idle or disabled), module and thus the
+ * sysconfig cannot be accessed and will probably lead to an "imprecise
+ * external abort"
+ */
+int am33xx_cm_wait_module_ready(u16 inst, s16 cdoffs, u16 clkctrl_offs)
+{
+	int i = 0;
+
+	if (!clkctrl_offs)
+		return 0;
+
+	omap_test_timeout(_is_module_ready(inst, cdoffs, clkctrl_offs),
+			  MAX_MODULE_READY_TIME, i);
+
+	return (i < MAX_MODULE_READY_TIME) ? 0 : -EBUSY;
+}
+
+/**
+ * am33xx_cm_wait_module_idle - wait for a module to be in 'disabled'
+ * state
+ * @inst: CM instance register offset (*_INST macro)
+ * @cdoffs: Clockdomain register offset (*_CDOFFS macro)
+ * @clkctrl_offs: Module clock control register offset (*_CLKCTRL macro)
+ *
+ * Wait for the module IDLEST to be disabled. Some PRCM transition,
+ * like reset assertion or parent clock de-activation must wait the
+ * module to be fully disabled.
+ */
+int am33xx_cm_wait_module_idle(u16 inst, s16 cdoffs, u16 clkctrl_offs)
+{
+	int i = 0;
+
+	if (!clkctrl_offs)
+		return 0;
+
+	omap_test_timeout((_clkctrl_idlest(inst, cdoffs, clkctrl_offs) ==
+				CLKCTRL_IDLEST_DISABLED),
+				MAX_MODULE_READY_TIME, i);
+
+	return (i < MAX_MODULE_READY_TIME) ? 0 : -EBUSY;
+}
+
+/**
+ * am33xx_cm_module_enable - Enable the modulemode inside CLKCTRL
+ * @mode: Module mode (SW or HW)
+ * @inst: CM instance register offset (*_INST macro)
+ * @cdoffs: Clockdomain register offset (*_CDOFFS macro)
+ * @clkctrl_offs: Module clock control register offset (*_CLKCTRL macro)
+ *
+ * No return value.
+ */
+void am33xx_cm_module_enable(u8 mode, u16 inst, s16 cdoffs, u16 clkctrl_offs)
+{
+	u32 v;
+
+	v = am33xx_cm_read_reg(inst, clkctrl_offs);
+	v &= ~AM33XX_MODULEMODE_MASK;
+	v |= mode << AM33XX_MODULEMODE_SHIFT;
+	am33xx_cm_write_reg(v, inst, clkctrl_offs);
+}
+
+/**
+ * am33xx_cm_module_disable - Disable the module inside CLKCTRL
+ * @inst: CM instance register offset (*_INST macro)
+ * @cdoffs: Clockdomain register offset (*_CDOFFS macro)
+ * @clkctrl_offs: Module clock control register offset (*_CLKCTRL macro)
+ *
+ * No return value.
+ */
+void am33xx_cm_module_disable(u16 inst, s16 cdoffs, u16 clkctrl_offs)
+{
+	u32 v;
+
+	v = am33xx_cm_read_reg(inst, clkctrl_offs);
+	v &= ~AM33XX_MODULEMODE_MASK;
+	am33xx_cm_write_reg(v, inst, clkctrl_offs);
+}

arch/arm/mach-omap2/common.h

@@ -120,6 +120,7 @@ extern void omap2_init_common_infrastructure(void);
 extern struct sys_timer omap2_timer;
 extern struct sys_timer omap3_timer;
 extern struct sys_timer omap3_secure_timer;
+extern struct sys_timer omap3_am33xx_timer;
 extern struct sys_timer omap4_timer;
 
 void omap2420_init_early(void);
@@ -128,8 +129,10 @@ void omap3430_init_early(void);
 void omap35xx_init_early(void);
 void omap3630_init_early(void);
 void omap3_init_early(void);	/* Do not use this one */
+void am33xx_init_early(void);
 void am35xx_init_early(void);
 void ti81xx_init_early(void);
+void am33xx_init_early(void);
 void omap4430_init_early(void);
 void omap3_init_late(void);	/* Do not use this one */
 void omap4430_init_late(void);

arch/arm/mach-omap2/control.h

@@ -21,6 +21,8 @@
 #include <mach/ctrl_module_pad_core_44xx.h>
 #include <mach/ctrl_module_pad_wkup_44xx.h>
 
+#include <plat/am33xx.h>
+
 #ifndef __ASSEMBLY__
 #define OMAP242X_CTRL_REGADDR(reg)					\
 		OMAP2_L4_IO_ADDRESS(OMAP242X_CTRL_BASE + (reg))
@@ -28,6 +30,8 @@
 		OMAP2_L4_IO_ADDRESS(OMAP243X_CTRL_BASE + (reg))
 #define OMAP343X_CTRL_REGADDR(reg)					\
 		OMAP2_L4_IO_ADDRESS(OMAP343X_CTRL_BASE + (reg))
+#define AM33XX_CTRL_REGADDR(reg)					\
+		AM33XX_L4_WK_IO_ADDRESS(AM33XX_SCM_BASE + (reg))
 #else
 #define OMAP242X_CTRL_REGADDR(reg)					\
 		OMAP2_L4_IO_ADDRESS(OMAP242X_CTRL_BASE + (reg))
@@ -35,6 +39,8 @@
 		OMAP2_L4_IO_ADDRESS(OMAP243X_CTRL_BASE + (reg))
 #define OMAP343X_CTRL_REGADDR(reg)					\
 		OMAP2_L4_IO_ADDRESS(OMAP343X_CTRL_BASE + (reg))
+#define AM33XX_CTRL_REGADDR(reg)					\
+		AM33XX_L4_WK_IO_ADDRESS(AM33XX_SCM_BASE + (reg))
 #endif /* __ASSEMBLY__ */
 
 /*
@@ -312,15 +318,15 @@
 						OMAP343X_SCRATCHPAD + reg)
 
 /* AM35XX_CONTROL_IPSS_CLK_CTRL bits */
-#define AM35XX_USBOTG_VBUSP_CLK_SHIFT   0
-#define AM35XX_CPGMAC_VBUSP_CLK_SHIFT   1
-#define AM35XX_VPFE_VBUSP_CLK_SHIFT     2
-#define AM35XX_HECC_VBUSP_CLK_SHIFT     3
-#define AM35XX_USBOTG_FCLK_SHIFT        8
-#define AM35XX_CPGMAC_FCLK_SHIFT        9
-#define AM35XX_VPFE_FCLK_SHIFT          10
-
-/*AM35XX CONTROL_LVL_INTR_CLEAR bits*/
+#define AM35XX_USBOTG_VBUSP_CLK_SHIFT	0
+#define AM35XX_CPGMAC_VBUSP_CLK_SHIFT	1
+#define AM35XX_VPFE_VBUSP_CLK_SHIFT	2
+#define AM35XX_HECC_VBUSP_CLK_SHIFT	3
+#define AM35XX_USBOTG_FCLK_SHIFT	8
+#define AM35XX_CPGMAC_FCLK_SHIFT	9
+#define AM35XX_VPFE_FCLK_SHIFT		10
+
+/* AM35XX CONTROL_LVL_INTR_CLEAR bits */
 #define AM35XX_CPGMAC_C0_MISC_PULSE_CLR	BIT(0)
 #define AM35XX_CPGMAC_C0_RX_PULSE_CLR	BIT(1)
 #define AM35XX_CPGMAC_C0_RX_THRESH_CLR	BIT(2)
@@ -330,21 +336,22 @@
 #define AM35XX_VPFE_CCDC_VD1_INT_CLR	BIT(6)
 #define AM35XX_VPFE_CCDC_VD2_INT_CLR	BIT(7)
 
-/*AM35XX CONTROL_IP_SW_RESET bits*/
+/* AM35XX CONTROL_IP_SW_RESET bits */
 #define AM35XX_USBOTGSS_SW_RST		BIT(0)
 #define AM35XX_CPGMACSS_SW_RST		BIT(1)
 #define AM35XX_VPFE_VBUSP_SW_RST	BIT(2)
 #define AM35XX_HECC_SW_RST		BIT(3)
 #define AM35XX_VPFE_PCLK_SW_RST		BIT(4)
 
-/*
- * CONTROL AM33XX STATUS register
- */
+/* AM33XX CONTROL_STATUS register */
 #define AM33XX_CONTROL_STATUS		0x040
+#define AM33XX_CONTROL_SEC_CLK_CTRL	0x1bc
 
-/*
- * CONTROL OMAP STATUS register to identify OMAP3 features
- */
+/* AM33XX CONTROL_STATUS bitfields (partial) */
+#define AM33XX_CONTROL_STATUS_SYSBOOT1_SHIFT		22
+#define AM33XX_CONTROL_STATUS_SYSBOOT1_MASK		(0x3 << 22)
+
+/* CONTROL OMAP STATUS register to identify OMAP3 features */
 #define OMAP3_CONTROL_OMAP_STATUS	0x044c
 
 #define OMAP3_SGX_SHIFT			13

arch/arm/mach-omap2/include/mach/debug-macro.S

@@ -72,6 +72,8 @@ omap_uart_lsr:	.word	0
 		beq	82f			@ configure UART2
 		cmp	\rp, #TI81XXUART3	@ ti81Xx UART offsets different
 		beq	83f			@ configure UART3
+		cmp	\rp, #AM33XXUART1	@ AM33XX UART offsets different
+		beq	84f			@ configure UART1
 		cmp	\rp, #ZOOM_UART		@ only on zoom2/3
 		beq	95f			@ configure ZOOM_UART
 
@@ -100,7 +102,9 @@ omap_uart_lsr:	.word	0
 		b	98f
 83:		mov	\rp, #UART_OFFSET(TI81XX_UART3_BASE)
 		b	98f
-
+84:		ldr	\rp, =AM33XX_UART1_BASE
+		and	\rp, \rp, #0x00ffffff
+		b	97f
 95:		ldr	\rp, =ZOOM_UART_BASE
 		str	\rp, [\tmp, #0]		@ omap_uart_phys
 		ldr	\rp, =ZOOM_UART_VIRT
@@ -109,6 +113,17 @@ omap_uart_lsr:	.word	0
 		str	\rp, [\tmp, #8]		@ omap_uart_lsr
 		b	10b
 
+		/* AM33XX: Store both phys and virt address for the uart */
+97:		add	\rp, \rp, #0x44000000	@ phys base
+		str	\rp, [\tmp, #0]		@ omap_uart_phys
+		sub	\rp, \rp, #0x44000000	@ phys base
+		add	\rp, \rp, #0xf9000000	@ virt base
+		str	\rp, [\tmp, #4]		@ omap_uart_virt
+		mov	\rp, #(UART_LSR << OMAP_PORT_SHIFT)
+		str	\rp, [\tmp, #8]		@ omap_uart_lsr
+
+		b	10b
+
 		/* Store both phys and virt address for the uart */
 98:		add	\rp, \rp, #0x48000000	@ phys base
 		str	\rp, [\tmp, #0]		@ omap_uart_phys

arch/arm/mach-omap2/io.c

@@ -477,6 +477,19 @@ void __init ti81xx_init_late(void)
 }
 #endif
 
+#ifdef CONFIG_SOC_AM33XX
+void __init am33xx_init_early(void)
+{
+	omap2_set_globals_am33xx();
+	omap3xxx_check_revision();
+	ti81xx_check_features();
+	omap_common_init_early();
+	am33xx_voltagedomains_init();
+	am33xx_powerdomains_init();
+	am33xx_clockdomains_init();
+}
+#endif
+
 #ifdef CONFIG_ARCH_OMAP4
 void __init omap4430_init_early(void)
 {

arch/arm/mach-omap2/irq.c

@@ -280,7 +280,7 @@ int __init omap_intc_of_init(struct device_node *node,
 	return 0;
 }
 
-#ifdef CONFIG_ARCH_OMAP3
+#if defined(CONFIG_ARCH_OMAP3) || defined(CONFIG_SOC_AM33XX)
 static struct omap3_intc_regs intc_context[ARRAY_SIZE(irq_banks)];
 
 void omap_intc_save_context(void)

arch/arm/mach-omap2/powerdomain.h

@@ -67,9 +67,9 @@
 
 /*
  * Maximum number of clockdomains that can be associated with a powerdomain.
- * CORE powerdomain on OMAP4 is the worst case
+ * PER powerdomain on AM33XX is the worst case
  */
-#define PWRDM_MAX_CLKDMS	9
+#define PWRDM_MAX_CLKDMS	11
 
 /* XXX A completely arbitrary number. What is reasonable here? */
 #define PWRDM_TRANSITION_BAILOUT 100000
@@ -92,6 +92,15 @@ struct powerdomain;
  * @pwrdm_clkdms: Clockdomains in this powerdomain
  * @node: list_head linking all powerdomains
  * @voltdm_node: list_head linking all powerdomains in a voltagedomain
+ * @pwrstctrl_offs: (AM33XX only) XXX_PWRSTCTRL reg offset from prcm_offs
+ * @pwrstst_offs: (AM33XX only) XXX_PWRSTST reg offset from prcm_offs
+ * @logicretstate_mask: (AM33XX only) mask for logic retention bitfield
+ *	in @pwrstctrl_offs
+ * @mem_on_mask: (AM33XX only) mask for mem on bitfield in @pwrstctrl_offs
+ * @mem_ret_mask: (AM33XX only) mask for mem ret bitfield in @pwrstctrl_offs
+ * @mem_pwrst_mask: (AM33XX only) mask for mem state bitfield in @pwrstst_offs
+ * @mem_retst_mask: (AM33XX only) mask for mem retention state bitfield
+ *	in @pwrstctrl_offs
  * @state:
  * @state_counter:
  * @timer:
@@ -121,6 +130,14 @@ struct powerdomain {
 	unsigned ret_logic_off_counter;
 	unsigned ret_mem_off_counter[PWRDM_MAX_MEM_BANKS];
 
+	const u8 pwrstctrl_offs;
+	const u8 pwrstst_offs;
+	const u32 logicretstate_mask;
+	const u32 mem_on_mask[PWRDM_MAX_MEM_BANKS];
+	const u32 mem_ret_mask[PWRDM_MAX_MEM_BANKS];
+	const u32 mem_pwrst_mask[PWRDM_MAX_MEM_BANKS];
+	const u32 mem_retst_mask[PWRDM_MAX_MEM_BANKS];
+
 #ifdef CONFIG_PM_DEBUG
 	s64 timer;
 	s64 state_timer[PWRDM_MAX_PWRSTS];
@@ -222,10 +239,12 @@ bool pwrdm_can_ever_lose_context(struct powerdomain *pwrdm);
 extern void omap242x_powerdomains_init(void);
 extern void omap243x_powerdomains_init(void);
 extern void omap3xxx_powerdomains_init(void);
+extern void am33xx_powerdomains_init(void);
 extern void omap44xx_powerdomains_init(void);
 
 extern struct pwrdm_ops omap2_pwrdm_operations;
 extern struct pwrdm_ops omap3_pwrdm_operations;
+extern struct pwrdm_ops am33xx_pwrdm_operations;
 extern struct pwrdm_ops omap4_pwrdm_operations;
 
 /* Common Internal functions used across OMAP rev's */

arch/arm/mach-omap2/powerdomains33xx_data.c

+/*
+ * AM33XX Power domain data
+ *
+ * Copyright (C) 2011-2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+
+#include "powerdomain.h"
+#include "prcm-common.h"
+#include "prm-regbits-33xx.h"
+#include "prm33xx.h"
+
+static struct powerdomain gfx_33xx_pwrdm = {
+	.name			= "gfx_pwrdm",
+	.voltdm			= { .name = "core" },
+	.prcm_offs		= AM33XX_PRM_GFX_MOD,
+	.pwrstctrl_offs		= AM33XX_PM_GFX_PWRSTCTRL_OFFSET,
+	.pwrstst_offs		= AM33XX_PM_GFX_PWRSTST_OFFSET,
+	.pwrsts			= PWRSTS_OFF_RET_ON,
+	.pwrsts_logic_ret	= PWRSTS_OFF_RET,
+	.flags			= PWRDM_HAS_LOWPOWERSTATECHANGE,
+	.banks			= 1,
+	.logicretstate_mask	= AM33XX_LOGICRETSTATE_MASK,
+	.mem_on_mask		= {
+		[0]		= AM33XX_GFX_MEM_ONSTATE_MASK,	/* gfx_mem */
+	},
+	.mem_ret_mask		= {
+		[0]		= AM33XX_GFX_MEM_RETSTATE_MASK,	/* gfx_mem */
+	},
+	.mem_pwrst_mask		= {
+		[0]		= AM33XX_GFX_MEM_STATEST_MASK,	/* gfx_mem */
+	},
+	.mem_retst_mask		= {
+		[0]		= AM33XX_GFX_MEM_RETSTATE_MASK,	/* gfx_mem */
+	},
+	.pwrsts_mem_ret		= {
+		[0]		= PWRSTS_OFF_RET,	/* gfx_mem */
+	},
+	.pwrsts_mem_on		= {
+		[0]		= PWRSTS_ON,		/* gfx_mem */
+	},
+};
+
+static struct powerdomain rtc_33xx_pwrdm = {
+	.name			= "rtc_pwrdm",
+	.voltdm			= { .name = "rtc" },
+	.prcm_offs		= AM33XX_PRM_RTC_MOD,
+	.pwrstctrl_offs		= AM33XX_PM_RTC_PWRSTCTRL_OFFSET,
+	.pwrstst_offs		= AM33XX_PM_RTC_PWRSTST_OFFSET,
+	.pwrsts			= PWRSTS_ON,
+	.logicretstate_mask	= AM33XX_LOGICRETSTATE_MASK,
+};
+
+static struct powerdomain wkup_33xx_pwrdm = {
+	.name			= "wkup_pwrdm",
+	.voltdm			= { .name = "core" },
+	.prcm_offs		= AM33XX_PRM_WKUP_MOD,
+	.pwrstctrl_offs		= AM33XX_PM_WKUP_PWRSTCTRL_OFFSET,
+	.pwrstst_offs		= AM33XX_PM_WKUP_PWRSTST_OFFSET,
+	.pwrsts			= PWRSTS_ON,
+	.logicretstate_mask	= AM33XX_LOGICRETSTATE_3_3_MASK,
+};
+
+static struct powerdomain per_33xx_pwrdm = {
+	.name			= "per_pwrdm",
+	.voltdm			= { .name = "core" },
+	.prcm_offs		= AM33XX_PRM_PER_MOD,
+	.pwrstctrl_offs		= AM33XX_PM_PER_PWRSTCTRL_OFFSET,
+	.pwrstst_offs		= AM33XX_PM_PER_PWRSTST_OFFSET,
+	.pwrsts			= PWRSTS_OFF_RET_ON,
+	.pwrsts_logic_ret	= PWRSTS_OFF_RET,
+	.flags			= PWRDM_HAS_LOWPOWERSTATECHANGE,
+	.banks			= 3,
+	.logicretstate_mask	= AM33XX_LOGICRETSTATE_3_3_MASK,
+	.mem_on_mask		= {
+		[0]		= AM33XX_PRUSS_MEM_ONSTATE_MASK, /* pruss_mem */
+		[1]		= AM33XX_PER_MEM_ONSTATE_MASK,	/* per_mem */
+		[2]		= AM33XX_RAM_MEM_ONSTATE_MASK,	/* ram_mem */
+	},
+	.mem_ret_mask		= {
+		[0]		= AM33XX_PRUSS_MEM_RETSTATE_MASK, /* pruss_mem */
+		[1]		= AM33XX_PER_MEM_RETSTATE_MASK,	/* per_mem */
+		[2]		= AM33XX_RAM_MEM_RETSTATE_MASK,	/* ram_mem */
+	},
+	.mem_pwrst_mask		= {
+		[0]		= AM33XX_PRUSS_MEM_STATEST_MASK, /* pruss_mem */
+		[1]		= AM33XX_PER_MEM_STATEST_MASK,	/* per_mem */
+		[2]		= AM33XX_RAM_MEM_STATEST_MASK,	/* ram_mem */
+	},
+	.mem_retst_mask		= {
+		[0]		= AM33XX_PRUSS_MEM_RETSTATE_MASK, /* pruss_mem */
+		[1]		= AM33XX_PER_MEM_RETSTATE_MASK,	/* per_mem */
+		[2]		= AM33XX_RAM_MEM_RETSTATE_MASK,	/* ram_mem */
+	},
+	.pwrsts_mem_ret		= {
+		[0]		= PWRSTS_OFF_RET,	/* pruss_mem */
+		[1]		= PWRSTS_OFF_RET,	/* per_mem */
+		[2]		= PWRSTS_OFF_RET,	/* ram_mem */
+	},
+	.pwrsts_mem_on		= {
+		[0]		= PWRSTS_ON,		/* pruss_mem */
+		[1]		= PWRSTS_ON,		/* per_mem */
+		[2]		= PWRSTS_ON,		/* ram_mem */
+	},
+};
+
+static struct powerdomain mpu_33xx_pwrdm = {
+	.name			= "mpu_pwrdm",
+	.voltdm			= { .name = "mpu" },
+	.prcm_offs		= AM33XX_PRM_MPU_MOD,
+	.pwrstctrl_offs		= AM33XX_PM_MPU_PWRSTCTRL_OFFSET,
+	.pwrstst_offs		= AM33XX_PM_MPU_PWRSTST_OFFSET,
+	.pwrsts			= PWRSTS_OFF_RET_ON,
+	.pwrsts_logic_ret	= PWRSTS_OFF_RET,
+	.flags			= PWRDM_HAS_LOWPOWERSTATECHANGE,
+	.banks			= 3,
+	.logicretstate_mask	= AM33XX_LOGICRETSTATE_MASK,
+	.mem_on_mask		= {
+		[0]		= AM33XX_MPU_L1_ONSTATE_MASK,	/* mpu_l1 */
+		[1]		= AM33XX_MPU_L2_ONSTATE_MASK,	/* mpu_l2 */
+		[2]		= AM33XX_MPU_RAM_ONSTATE_MASK,	/* mpu_ram */
+	},
+	.mem_ret_mask		= {
+		[0]		= AM33XX_MPU_L1_RETSTATE_MASK,	/* mpu_l1 */
+		[1]		= AM33XX_MPU_L2_RETSTATE_MASK,	/* mpu_l2 */
+		[2]		= AM33XX_MPU_RAM_RETSTATE_MASK,	/* mpu_ram */
+	},
+	.mem_pwrst_mask		= {
+		[0]		= AM33XX_MPU_L1_STATEST_MASK,	/* mpu_l1 */
+		[1]		= AM33XX_MPU_L2_STATEST_MASK,	/* mpu_l2 */
+		[2]		= AM33XX_MPU_RAM_STATEST_MASK,	/* mpu_ram */
+	},
+	.mem_retst_mask		= {
+		[0]		= AM33XX_MPU_L1_RETSTATE_MASK,	/* mpu_l1 */
+		[1]		= AM33XX_MPU_L2_RETSTATE_MASK,	/* mpu_l2 */
+		[2]		= AM33XX_MPU_RAM_RETSTATE_MASK,	/* mpu_ram */
+	},
+	.pwrsts_mem_ret		= {
+		[0]		= PWRSTS_OFF_RET,	/* mpu_l1 */
+		[1]		= PWRSTS_OFF_RET,	/* mpu_l2 */
+		[2]		= PWRSTS_OFF_RET,	/* mpu_ram */
+	},
+	.pwrsts_mem_on		= {
+		[0]		= PWRSTS_ON,		/* mpu_l1 */
+		[1]		= PWRSTS_ON,		/* mpu_l2 */
+		[2]		= PWRSTS_ON,		/* mpu_ram */
+	},
+};
+
+static struct powerdomain cefuse_33xx_pwrdm = {
+	.name		= "cefuse_pwrdm",
+	.voltdm		= { .name = "core" },
+	.prcm_offs	= AM33XX_PRM_CEFUSE_MOD,
+	.pwrstctrl_offs	= AM33XX_PM_CEFUSE_PWRSTCTRL_OFFSET,
+	.pwrstst_offs	= AM33XX_PM_CEFUSE_PWRSTST_OFFSET,
+	.pwrsts		= PWRSTS_OFF_ON,
+};
+
+static struct powerdomain *powerdomains_am33xx[] __initdata = {
+	&gfx_33xx_pwrdm,
+	&rtc_33xx_pwrdm,
+	&wkup_33xx_pwrdm,
+	&per_33xx_pwrdm,
+	&mpu_33xx_pwrdm,
+	&cefuse_33xx_pwrdm,
+	NULL,
+};
+
+void __init am33xx_powerdomains_init(void)
+{
+	pwrdm_register_platform_funcs(&am33xx_pwrdm_operations);
+	pwrdm_register_pwrdms(powerdomains_am33xx);
+	pwrdm_complete_init();
+}

arch/arm/mach-omap2/timer.c

@@ -368,6 +368,11 @@ OMAP_SYS_TIMER_INIT(3_secure, OMAP3_SECURE_TIMER, OMAP3_CLKEV_SOURCE,
 OMAP_SYS_TIMER(3_secure)
 #endif
 
+#ifdef CONFIG_SOC_AM33XX
+OMAP_SYS_TIMER_INIT(3_am33xx, 1, OMAP4_MPU_SOURCE, 2, OMAP4_MPU_SOURCE)
+OMAP_SYS_TIMER(3_am33xx)
+#endif
+
 #ifdef CONFIG_ARCH_OMAP4
 #ifdef CONFIG_LOCAL_TIMERS
 static DEFINE_TWD_LOCAL_TIMER(twd_local_timer,

arch/arm/mach-omap2/voltage.h

@@ -156,6 +156,7 @@ int omap_voltage_late_init(void);
 
 extern void omap2xxx_voltagedomains_init(void);
 extern void omap3xxx_voltagedomains_init(void);
+extern void am33xx_voltagedomains_init(void);
 extern void omap44xx_voltagedomains_init(void);
 
 struct voltagedomain *voltdm_lookup(const char *name);

include/linux/platform_data/clk-nomadik.h

+/* Minimal platform data header */
+void nomadik_clk_init(void);