[media] media: i2c: adv7343: make the platform data members as array

This patch makes the platform data members as array wherever
possible, so as this makes easier while collecting the data
in DT case and read the entire array at once.
This patch also makes appropriate changes to board-da850-evm.c
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

arch/arm/mach-davinci/board-da850-evm.c

@@ -1249,12 +1249,10 @@ static struct vpif_capture_config da850_vpif_capture_config = {
 
 static struct adv7343_platform_data adv7343_pdata = {
 	.mode_config = {
-		.dac_3 = 1,
-		.dac_2 = 1,
-		.dac_1 = 1,
+		.dac = { 1, 1, 1 },
 	},
 	.sd_config = {
-		.sd_dac_out1 = 1,
+		.sd_dac_out = { 1 },
 	},
 };
 

drivers/media/i2c/adv7343.c

@@ -227,12 +227,12 @@ static int adv7343_setoutput(struct v4l2_subdev *sd, u32 output_type)
 	else
 		val = state->pdata->mode_config.sleep_mode << 0 |
 		      state->pdata->mode_config.pll_control << 1 |
-		      state->pdata->mode_config.dac_3 << 2 |
-		      state->pdata->mode_config.dac_2 << 3 |
-		      state->pdata->mode_config.dac_1 << 4 |
-		      state->pdata->mode_config.dac_6 << 5 |
-		      state->pdata->mode_config.dac_5 << 6 |
-		      state->pdata->mode_config.dac_4 << 7;
+		      state->pdata->mode_config.dac[2] << 2 |
+		      state->pdata->mode_config.dac[1] << 3 |
+		      state->pdata->mode_config.dac[0] << 4 |
+		      state->pdata->mode_config.dac[5] << 5 |
+		      state->pdata->mode_config.dac[4] << 6 |
+		      state->pdata->mode_config.dac[3] << 7;
 
 	err = adv7343_write(sd, ADV7343_POWER_MODE_REG, val);
 	if (err < 0)
@@ -251,15 +251,15 @@ static int adv7343_setoutput(struct v4l2_subdev *sd, u32 output_type)
 	/* configure SD DAC Output 2 and SD DAC Output 1 bit to zero */
 	val = state->reg82 & (SD_DAC_1_DI & SD_DAC_2_DI);
 
-	if (state->pdata && state->pdata->sd_config.sd_dac_out1)
-		val = val | (state->pdata->sd_config.sd_dac_out1 << 1);
-	else if (state->pdata && !state->pdata->sd_config.sd_dac_out1)
-		val = val & ~(state->pdata->sd_config.sd_dac_out1 << 1);
+	if (state->pdata && state->pdata->sd_config.sd_dac_out[0])
+		val = val | (state->pdata->sd_config.sd_dac_out[0] << 1);
+	else if (state->pdata && !state->pdata->sd_config.sd_dac_out[0])
+		val = val & ~(state->pdata->sd_config.sd_dac_out[0] << 1);
 
-	if (state->pdata && state->pdata->sd_config.sd_dac_out2)
-		val = val | (state->pdata->sd_config.sd_dac_out2 << 2);
-	else if (state->pdata && !state->pdata->sd_config.sd_dac_out2)
-		val = val & ~(state->pdata->sd_config.sd_dac_out2 << 2);
+	if (state->pdata && state->pdata->sd_config.sd_dac_out[1])
+		val = val | (state->pdata->sd_config.sd_dac_out[1] << 2);
+	else if (state->pdata && !state->pdata->sd_config.sd_dac_out[1])
+		val = val & ~(state->pdata->sd_config.sd_dac_out[1] << 2);
 
 	err = adv7343_write(sd, ADV7343_SD_MODE_REG2, val);
 	if (err < 0)

include/media/adv7343.h

@@ -28,12 +28,7 @@
  * @pll_control: PLL and oversampling control. This control allows internal
  *		 PLL 1 circuit to be powered down and the oversampling to be
  *		 switched off.
- * @dac_1: power on/off DAC 1.
- * @dac_2: power on/off DAC 2.
- * @dac_3: power on/off DAC 3.
- * @dac_4: power on/off DAC 4.
- * @dac_5: power on/off DAC 5.
- * @dac_6: power on/off DAC 6.
+ * @dac: array to configure power on/off DAC's 1..6
  *
  * Power mode register (Register 0x0), for more info refer REGISTER MAP ACCESS
  * section of datasheet[1], table 17 page no 30.
@@ -43,23 +38,16 @@
 struct adv7343_power_mode {
 	bool sleep_mode;
 	bool pll_control;
-	bool dac_1;
-	bool dac_2;
-	bool dac_3;
-	bool dac_4;
-	bool dac_5;
-	bool dac_6;
+	u32 dac[6];
 };
 
 /**
  * struct adv7343_sd_config - SD Only Output Configuration.
- * @sd_dac_out1: Configure SD DAC Output 1.
- * @sd_dac_out2: Configure SD DAC Output 2.
+ * @sd_dac_out: array configuring SD DAC Outputs 1 and 2
  */
 struct adv7343_sd_config {
 	/* SD only Output Configuration */
-	bool sd_dac_out1;
-	bool sd_dac_out2;
+	u32 sd_dac_out[2];
 };
 
 /**