Commit 5ec55823 authored by Joakim Zhang's avatar Joakim Zhang Committed by David S. Miller

net: stmmac: add clocks management for gmac driver

This patch intends to add clocks management for stmmac driver:

If CONFIG_PM enabled:
1. Keep clocks disabled after driver probed.
2. Enable clocks when up the net device, and disable clocks when down
the net device.

If CONFIG_PM disabled:
Keep clocks always enabled after driver probed.

Note:
1. It is fine for ethtool, since the way of implementing ethtool_ops::begin
in stmmac is only can be accessed when interface is enabled, so the clocks
are ticked.
2. The MDIO bus has a different life cycle to the MAC, need ensure
clocks are enabled when _mdio_read/write() need clocks, because these
functions can be called while the interface it not opened.
Reviewed-by: default avatarAndrew Lunn <andrew@lunn.ch>
Signed-off-by: default avatarJoakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent 91de5ac9
......@@ -272,6 +272,7 @@ void stmmac_disable_eee_mode(struct stmmac_priv *priv);
bool stmmac_eee_init(struct stmmac_priv *priv);
int stmmac_reinit_queues(struct net_device *dev, u32 rx_cnt, u32 tx_cnt);
int stmmac_reinit_ringparam(struct net_device *dev, u32 rx_size, u32 tx_size);
int stmmac_bus_clks_config(struct stmmac_priv *priv, bool enabled);
#if IS_ENABLED(CONFIG_STMMAC_SELFTESTS)
void stmmac_selftest_run(struct net_device *dev,
......
......@@ -28,6 +28,7 @@
#include <linux/if_vlan.h>
#include <linux/dma-mapping.h>
#include <linux/slab.h>
#include <linux/pm_runtime.h>
#include <linux/prefetch.h>
#include <linux/pinctrl/consumer.h>
#ifdef CONFIG_DEBUG_FS
......@@ -113,6 +114,28 @@ static void stmmac_exit_fs(struct net_device *dev);
#define STMMAC_COAL_TIMER(x) (ns_to_ktime((x) * NSEC_PER_USEC))
int stmmac_bus_clks_config(struct stmmac_priv *priv, bool enabled)
{
int ret = 0;
if (enabled) {
ret = clk_prepare_enable(priv->plat->stmmac_clk);
if (ret)
return ret;
ret = clk_prepare_enable(priv->plat->pclk);
if (ret) {
clk_disable_unprepare(priv->plat->stmmac_clk);
return ret;
}
} else {
clk_disable_unprepare(priv->plat->stmmac_clk);
clk_disable_unprepare(priv->plat->pclk);
}
return ret;
}
EXPORT_SYMBOL_GPL(stmmac_bus_clks_config);
/**
* stmmac_verify_args - verify the driver parameters.
* Description: it checks the driver parameters and set a default in case of
......@@ -2896,6 +2919,12 @@ static int stmmac_open(struct net_device *dev)
u32 chan;
int ret;
ret = pm_runtime_get_sync(priv->device);
if (ret < 0) {
pm_runtime_put_noidle(priv->device);
return ret;
}
if (priv->hw->pcs != STMMAC_PCS_TBI &&
priv->hw->pcs != STMMAC_PCS_RTBI &&
priv->hw->xpcs_args.an_mode != DW_AN_C73) {
......@@ -2904,7 +2933,7 @@ static int stmmac_open(struct net_device *dev)
netdev_err(priv->dev,
"%s: Cannot attach to PHY (error: %d)\n",
__func__, ret);
return ret;
goto init_phy_error;
}
}
......@@ -3020,6 +3049,8 @@ static int stmmac_open(struct net_device *dev)
free_dma_desc_resources(priv);
dma_desc_error:
phylink_disconnect_phy(priv->phylink);
init_phy_error:
pm_runtime_put(priv->device);
return ret;
}
......@@ -3070,6 +3101,8 @@ static int stmmac_release(struct net_device *dev)
stmmac_release_ptp(priv);
pm_runtime_put(priv->device);
return 0;
}
......@@ -4706,6 +4739,12 @@ static int stmmac_vlan_rx_add_vid(struct net_device *ndev, __be16 proto, u16 vid
bool is_double = false;
int ret;
ret = pm_runtime_get_sync(priv->device);
if (ret < 0) {
pm_runtime_put_noidle(priv->device);
return ret;
}
if (be16_to_cpu(proto) == ETH_P_8021AD)
is_double = true;
......@@ -4739,10 +4778,15 @@ static int stmmac_vlan_rx_kill_vid(struct net_device *ndev, __be16 proto, u16 vi
if (priv->hw->num_vlan) {
ret = stmmac_del_hw_vlan_rx_fltr(priv, ndev, priv->hw, proto, vid);
if (ret)
return ret;
goto del_vlan_error;
}
return stmmac_vlan_update(priv, is_double);
ret = stmmac_vlan_update(priv, is_double);
del_vlan_error:
pm_runtime_put(priv->device);
return ret;
}
static const struct net_device_ops stmmac_netdev_ops = {
......@@ -5181,6 +5225,10 @@ int stmmac_dvr_probe(struct device *device,
stmmac_check_pcs_mode(priv);
pm_runtime_get_noresume(device);
pm_runtime_set_active(device);
pm_runtime_enable(device);
if (priv->hw->pcs != STMMAC_PCS_TBI &&
priv->hw->pcs != STMMAC_PCS_RTBI) {
/* MDIO bus Registration */
......@@ -5218,6 +5266,11 @@ int stmmac_dvr_probe(struct device *device,
stmmac_init_fs(ndev);
#endif
/* Let pm_runtime_put() disable the clocks.
* If CONFIG_PM is not enabled, the clocks will stay powered.
*/
pm_runtime_put(device);
return ret;
error_serdes_powerup:
......@@ -5232,6 +5285,7 @@ int stmmac_dvr_probe(struct device *device,
stmmac_napi_del(ndev);
error_hw_init:
destroy_workqueue(priv->wq);
stmmac_bus_clks_config(priv, false);
return ret;
}
......@@ -5267,8 +5321,8 @@ int stmmac_dvr_remove(struct device *dev)
phylink_destroy(priv->phylink);
if (priv->plat->stmmac_rst)
reset_control_assert(priv->plat->stmmac_rst);
clk_disable_unprepare(priv->plat->pclk);
clk_disable_unprepare(priv->plat->stmmac_clk);
pm_runtime_put(dev);
pm_runtime_disable(dev);
if (priv->hw->pcs != STMMAC_PCS_TBI &&
priv->hw->pcs != STMMAC_PCS_RTBI)
stmmac_mdio_unregister(ndev);
......@@ -5291,6 +5345,7 @@ int stmmac_suspend(struct device *dev)
struct net_device *ndev = dev_get_drvdata(dev);
struct stmmac_priv *priv = netdev_priv(ndev);
u32 chan;
int ret;
if (!ndev || !netif_running(ndev))
return 0;
......@@ -5334,8 +5389,9 @@ int stmmac_suspend(struct device *dev)
pinctrl_pm_select_sleep_state(priv->device);
/* Disable clock in case of PWM is off */
clk_disable_unprepare(priv->plat->clk_ptp_ref);
clk_disable_unprepare(priv->plat->pclk);
clk_disable_unprepare(priv->plat->stmmac_clk);
ret = pm_runtime_force_suspend(dev);
if (ret)
return ret;
}
mutex_unlock(&priv->lock);
......@@ -5401,8 +5457,9 @@ int stmmac_resume(struct device *dev)
} else {
pinctrl_pm_select_default_state(priv->device);
/* enable the clk previously disabled */
clk_prepare_enable(priv->plat->stmmac_clk);
clk_prepare_enable(priv->plat->pclk);
ret = pm_runtime_force_resume(dev);
if (ret)
return ret;
if (priv->plat->clk_ptp_ref)
clk_prepare_enable(priv->plat->clk_ptp_ref);
/* reset the phy so that it's ready */
......
......@@ -15,6 +15,7 @@
#include <linux/iopoll.h>
#include <linux/mii.h>
#include <linux/of_mdio.h>
#include <linux/pm_runtime.h>
#include <linux/phy.h>
#include <linux/property.h>
#include <linux/slab.h>
......@@ -87,21 +88,29 @@ static int stmmac_xgmac2_mdio_read(struct mii_bus *bus, int phyaddr, int phyreg)
u32 tmp, addr, value = MII_XGMAC_BUSY;
int ret;
ret = pm_runtime_get_sync(priv->device);
if (ret < 0) {
pm_runtime_put_noidle(priv->device);
return ret;
}
/* Wait until any existing MII operation is complete */
if (readl_poll_timeout(priv->ioaddr + mii_data, tmp,
!(tmp & MII_XGMAC_BUSY), 100, 10000))
return -EBUSY;
!(tmp & MII_XGMAC_BUSY), 100, 10000)) {
ret = -EBUSY;
goto err_disable_clks;
}
if (phyreg & MII_ADDR_C45) {
phyreg &= ~MII_ADDR_C45;
ret = stmmac_xgmac2_c45_format(priv, phyaddr, phyreg, &addr);
if (ret)
return ret;
goto err_disable_clks;
} else {
ret = stmmac_xgmac2_c22_format(priv, phyaddr, phyreg, &addr);
if (ret)
return ret;
goto err_disable_clks;
value |= MII_XGMAC_SADDR;
}
......@@ -112,8 +121,10 @@ static int stmmac_xgmac2_mdio_read(struct mii_bus *bus, int phyaddr, int phyreg)
/* Wait until any existing MII operation is complete */
if (readl_poll_timeout(priv->ioaddr + mii_data, tmp,
!(tmp & MII_XGMAC_BUSY), 100, 10000))
return -EBUSY;
!(tmp & MII_XGMAC_BUSY), 100, 10000)) {
ret = -EBUSY;
goto err_disable_clks;
}
/* Set the MII address register to read */
writel(addr, priv->ioaddr + mii_address);
......@@ -121,11 +132,18 @@ static int stmmac_xgmac2_mdio_read(struct mii_bus *bus, int phyaddr, int phyreg)
/* Wait until any existing MII operation is complete */
if (readl_poll_timeout(priv->ioaddr + mii_data, tmp,
!(tmp & MII_XGMAC_BUSY), 100, 10000))
return -EBUSY;
!(tmp & MII_XGMAC_BUSY), 100, 10000)) {
ret = -EBUSY;
goto err_disable_clks;
}
/* Read the data from the MII data register */
return readl(priv->ioaddr + mii_data) & GENMASK(15, 0);
ret = (int)readl(priv->ioaddr + mii_data) & GENMASK(15, 0);
err_disable_clks:
pm_runtime_put(priv->device);
return ret;
}
static int stmmac_xgmac2_mdio_write(struct mii_bus *bus, int phyaddr,
......@@ -138,21 +156,29 @@ static int stmmac_xgmac2_mdio_write(struct mii_bus *bus, int phyaddr,
u32 addr, tmp, value = MII_XGMAC_BUSY;
int ret;
ret = pm_runtime_get_sync(priv->device);
if (ret < 0) {
pm_runtime_put_noidle(priv->device);
return ret;
}
/* Wait until any existing MII operation is complete */
if (readl_poll_timeout(priv->ioaddr + mii_data, tmp,
!(tmp & MII_XGMAC_BUSY), 100, 10000))
return -EBUSY;
!(tmp & MII_XGMAC_BUSY), 100, 10000)) {
ret = -EBUSY;
goto err_disable_clks;
}
if (phyreg & MII_ADDR_C45) {
phyreg &= ~MII_ADDR_C45;
ret = stmmac_xgmac2_c45_format(priv, phyaddr, phyreg, &addr);
if (ret)
return ret;
goto err_disable_clks;
} else {
ret = stmmac_xgmac2_c22_format(priv, phyaddr, phyreg, &addr);
if (ret)
return ret;
goto err_disable_clks;
value |= MII_XGMAC_SADDR;
}
......@@ -164,16 +190,23 @@ static int stmmac_xgmac2_mdio_write(struct mii_bus *bus, int phyaddr,
/* Wait until any existing MII operation is complete */
if (readl_poll_timeout(priv->ioaddr + mii_data, tmp,
!(tmp & MII_XGMAC_BUSY), 100, 10000))
return -EBUSY;
!(tmp & MII_XGMAC_BUSY), 100, 10000)) {
ret = -EBUSY;
goto err_disable_clks;
}
/* Set the MII address register to write */
writel(addr, priv->ioaddr + mii_address);
writel(value, priv->ioaddr + mii_data);
/* Wait until any existing MII operation is complete */
return readl_poll_timeout(priv->ioaddr + mii_data, tmp,
!(tmp & MII_XGMAC_BUSY), 100, 10000);
ret = readl_poll_timeout(priv->ioaddr + mii_data, tmp,
!(tmp & MII_XGMAC_BUSY), 100, 10000);
err_disable_clks:
pm_runtime_put(priv->device);
return ret;
}
/**
......@@ -196,6 +229,12 @@ static int stmmac_mdio_read(struct mii_bus *bus, int phyaddr, int phyreg)
int data = 0;
u32 v;
data = pm_runtime_get_sync(priv->device);
if (data < 0) {
pm_runtime_put_noidle(priv->device);
return data;
}
value |= (phyaddr << priv->hw->mii.addr_shift)
& priv->hw->mii.addr_mask;
value |= (phyreg << priv->hw->mii.reg_shift) & priv->hw->mii.reg_mask;
......@@ -216,19 +255,26 @@ static int stmmac_mdio_read(struct mii_bus *bus, int phyaddr, int phyreg)
}
if (readl_poll_timeout(priv->ioaddr + mii_address, v, !(v & MII_BUSY),
100, 10000))
return -EBUSY;
100, 10000)) {
data = -EBUSY;
goto err_disable_clks;
}
writel(data, priv->ioaddr + mii_data);
writel(value, priv->ioaddr + mii_address);
if (readl_poll_timeout(priv->ioaddr + mii_address, v, !(v & MII_BUSY),
100, 10000))
return -EBUSY;
100, 10000)) {
data = -EBUSY;
goto err_disable_clks;
}
/* Read the data from the MII data register */
data = (int)readl(priv->ioaddr + mii_data) & MII_DATA_MASK;
err_disable_clks:
pm_runtime_put(priv->device);
return data;
}
......@@ -247,10 +293,16 @@ static int stmmac_mdio_write(struct mii_bus *bus, int phyaddr, int phyreg,
struct stmmac_priv *priv = netdev_priv(ndev);
unsigned int mii_address = priv->hw->mii.addr;
unsigned int mii_data = priv->hw->mii.data;
int ret, data = phydata;
u32 value = MII_BUSY;
int data = phydata;
u32 v;
ret = pm_runtime_get_sync(priv->device);
if (ret < 0) {
pm_runtime_put_noidle(priv->device);
return ret;
}
value |= (phyaddr << priv->hw->mii.addr_shift)
& priv->hw->mii.addr_mask;
value |= (phyreg << priv->hw->mii.reg_shift) & priv->hw->mii.reg_mask;
......@@ -275,16 +327,23 @@ static int stmmac_mdio_write(struct mii_bus *bus, int phyaddr, int phyreg,
/* Wait until any existing MII operation is complete */
if (readl_poll_timeout(priv->ioaddr + mii_address, v, !(v & MII_BUSY),
100, 10000))
return -EBUSY;
100, 10000)) {
ret = -EBUSY;
goto err_disable_clks;
}
/* Set the MII address register to write */
writel(data, priv->ioaddr + mii_data);
writel(value, priv->ioaddr + mii_address);
/* Wait until any existing MII operation is complete */
return readl_poll_timeout(priv->ioaddr + mii_address, v, !(v & MII_BUSY),
100, 10000);
ret = readl_poll_timeout(priv->ioaddr + mii_address, v, !(v & MII_BUSY),
100, 10000);
err_disable_clks:
pm_runtime_put(priv->device);
return ret;
}
/**
......
......@@ -744,10 +744,30 @@ static int stmmac_pltfr_resume(struct device *dev)
return stmmac_resume(dev);
}
static int stmmac_runtime_suspend(struct device *dev)
{
struct net_device *ndev = dev_get_drvdata(dev);
struct stmmac_priv *priv = netdev_priv(ndev);
stmmac_bus_clks_config(priv, false);
return 0;
}
static int stmmac_runtime_resume(struct device *dev)
{
struct net_device *ndev = dev_get_drvdata(dev);
struct stmmac_priv *priv = netdev_priv(ndev);
return stmmac_bus_clks_config(priv, true);
}
#endif /* CONFIG_PM_SLEEP */
SIMPLE_DEV_PM_OPS(stmmac_pltfr_pm_ops, stmmac_pltfr_suspend,
stmmac_pltfr_resume);
const struct dev_pm_ops stmmac_pltfr_pm_ops = {
SET_SYSTEM_SLEEP_PM_OPS(stmmac_pltfr_suspend, stmmac_pltfr_resume)
SET_RUNTIME_PM_OPS(stmmac_runtime_suspend, stmmac_runtime_resume, NULL)
};
EXPORT_SYMBOL_GPL(stmmac_pltfr_pm_ops);
MODULE_DESCRIPTION("STMMAC 10/100/1000 Ethernet platform support");
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment