ARM: dts: at91: ariag25: Style cleanup

- newline between properties and sub-nodes
- use tags from included dtsi instead of duplicating the hierarchy

There are no differences in the generated .dtb
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Link: https://lore.kernel.org/r/20190812212757.23432-2-uwe@kleine-koenig.orgSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

arch/arm/boot/dts/at91-ariag25.dts

@@ -14,11 +14,6 @@ / {
 		     "atmel,at91sam9x5", "atmel,at91sam9";
 
 	aliases {
-		serial0 = &dbgu;
-		serial1 = &usart0;
-		serial2 = &usart1;
-		serial3 = &usart2;
-		serial4 = &usart3;
 		serial5 = &uart0;
 		serial6 = &uart1;
 	};
@@ -42,132 +37,6 @@ main_xtal {
 		};
 	};
 
-	ahb {
-		apb {
-			mmc0: mmc@f0008000 {
-				/* N.B. Aria has no SD card detect (CD), assumed present */
-
-				pinctrl-0 = <
-					&pinctrl_mmc0_slot0_clk_cmd_dat0
-					&pinctrl_mmc0_slot0_dat1_3>;
-				status = "okay";
-				slot@0 {
-					reg = <0>;
-					bus-width = <4>;
-				};
-			};
-
-			tcb0: timer@f8008000 {
-				timer@0 {
-					compatible = "atmel,tcb-timer";
-					reg = <0>;
-				};
-
-				timer@1 {
-					compatible = "atmel,tcb-timer";
-					reg = <1>;
-				};
-			};
-
-			i2c0: i2c@f8010000 {
-				status = "okay";
-			};
-
-			i2c1: i2c@f8014000 {
-				status = "okay";
-			};
-
-			/* TWD2+TCLK2 hidden behind ethernet, so no i2c2 */
-
-			usart0: serial@f801c000 {
-				pinctrl-0 = <&pinctrl_usart0
-					     &pinctrl_usart0_rts
-					     &pinctrl_usart0_cts>;
-				status = "okay";
-			};
-
-			usart1: serial@f8020000 {
-				pinctrl-0 = <&pinctrl_usart1
-					     /* &pinctrl_usart1_rts */
-					     /* &pinctrl_usart1_cts */
-					    >;
-				status = "okay";
-			};
-
-			usart2: serial@f8024000 {
-				/* cannot activate RTS2+CTS2, clash with
-				 * ethernet on PB0 and PB1 */
-				pinctrl-0 = <&pinctrl_usart2>;
-				status = "okay";
-			};
-
-			usart3: serial@f8028000 {
-				compatible = "atmel,at91sam9260-usart";
-				reg = <0xf8028000 0x200>;
-				interrupts = <8 4 5>;
-				pinctrl-names = "default";
-				pinctrl-0 = <&pinctrl_usart3
-					     /* &pinctrl_usart3_rts */
-					     /* &pinctrl_usart3_cts */
-					    >;
-				status = "okay";
-			};
-
-			macb0: ethernet@f802c000 {
-				phy-mode = "rmii";
-				/*
-				 * following can be overwritten by bootloader:
-				 * for example u-boot 'ftd set' command
-				 */
-				local-mac-address = [00 00 00 00 00 00];
-				status = "okay";
-			};
-
-			/*
-			 * UART0/1 pins are marked as GPIO on
-			 * Aria documentation.
-			 * Change to "okay" if you need additional serial ports
-			 */
-			uart0: serial@f8040000 {
-				status = "disabled";
-			};
-
-			uart1: serial@f8044000 {
-				status = "disabled";
-			};
-
-			adc0: adc@f804c000 {
-				status = "okay";
-				atmel,adc-channels-used = <0xf>;
-			};
-
-			dbgu: serial@fffff200 {
-				status = "okay";
-			};
-
-			pinctrl@fffff400 {
-				w1_0 {
-					pinctrl_w1_0: w1_0-0 {
-						atmel,pins = <0 21 0x0 0x1>; /* PA21 PIO, pull-up */
-					};
-				};
-			};
-
-			rtc@fffffeb0 {
-				status = "okay";
-			};
-		};
-
-		usb0: ohci@600000 {
-			status = "okay";
-			num-ports = <3>;
-		};
-
-		usb1: ehci@700000 {
-			status = "okay";
-		};
-	};
-
 	leds {
 		compatible = "gpio-leds";
 
@@ -187,3 +56,127 @@ onewire {
 		pinctrl-0 = <&pinctrl_w1_0>;
 	};
 };
+
+&adc0 {
+	status = "okay";
+	atmel,adc-channels-used = <0xf>;
+};
+
+&dbgu {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+/* TWD2+TCLK2 hidden behind ethernet, so no i2c2 */
+
+&macb0 {
+	phy-mode = "rmii";
+	/*
+	 * following can be overwritten by bootloader:
+	 * for example u-boot 'ftd set' command
+	 */
+	local-mac-address = [00 00 00 00 00 00];
+	status = "okay";
+};
+
+
+&mmc0 {
+	/* N.B. Aria has no SD card detect (CD), assumed present */
+
+	pinctrl-0 = <
+		&pinctrl_mmc0_slot0_clk_cmd_dat0
+		&pinctrl_mmc0_slot0_dat1_3>;
+	status = "okay";
+
+	slot@0 {
+		reg = <0>;
+		bus-width = <4>;
+	};
+};
+
+&pinctrl {
+	w1_0 {
+		pinctrl_w1_0: w1_0-0 {
+			atmel,pins = <0 21 0x0 0x1>; /* PA21 PIO, pull-up */
+		};
+	};
+};
+
+&rtc {
+	status = "okay";
+};
+
+&tcb0 {
+	timer@0 {
+		compatible = "atmel,tcb-timer";
+		reg = <0>;
+	};
+
+	timer@1 {
+		compatible = "atmel,tcb-timer";
+		reg = <1>;
+	};
+};
+
+/*
+ * UART0/1 pins are marked as GPIO on
+ * Aria documentation.
+ * Change to "okay" if you need additional serial ports
+ */
+&uart0 {
+	status = "disabled";
+};
+
+&uart1 {
+	status = "disabled";
+};
+
+&usart0 {
+	pinctrl-0 = <&pinctrl_usart0
+		     &pinctrl_usart0_rts
+		     &pinctrl_usart0_cts>;
+	status = "okay";
+};
+
+&usart1 {
+	pinctrl-0 = <&pinctrl_usart1
+		     /* &pinctrl_usart1_rts */
+		     /* &pinctrl_usart1_cts */
+		    >;
+	status = "okay";
+};
+
+&usart2 {
+	/* cannot activate RTS2+CTS2, clash with
+	 * ethernet on PB0 and PB1 */
+	pinctrl-0 = <&pinctrl_usart2>;
+	status = "okay";
+};
+
+&usart3 {
+	compatible = "atmel,at91sam9260-usart";
+	reg = <0xf8028000 0x200>;
+	interrupts = <8 4 5>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usart3
+		     /* &pinctrl_usart3_rts */
+		     /* &pinctrl_usart3_cts */
+		    >;
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+	num-ports = <3>;
+};
+
+&usb1 {
+	status = "okay";
+};