USB: add iuu_phoenix driver

Signed-off-by: Alain Degreffe <eczema@ecze.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Documentation/usb/iuu_phoenix.txt

+Infinity Usb Unlimited Readme
+-----------------------------
+
+Hi all,
+
+
+This module provide a serial interface to use your
+IUU unit in phoenix mode. Loading this module will
+bring a ttyUSB[0-x] interface. This driver must be
+used by your favorite application to pilot the IUU
+
+This driver is still in beta stage, so bugs can
+occur and your system may freeze. As far I now,
+I never had any problem with it, but I'm not a real
+guru, so don't blame me if your system is unstable
+
+You can plug more than one IUU. Every unit will
+have his own device file(/dev/ttyUSB0,/dev/ttyUSB1,...)
+
+
+
+How to tune the reader speed ?
+
+ A few parameters can be used at load time
+ To use parameters, just unload the module if it is
+ already loaded and use modprobe iuu_phoenix param=value.
+ In case of prebuilt module, use the command
+ insmod iuu_phoenix param=value.
+
+ Example:
+
+ modprobe iuu_phoenix clockmode=3
+
+ The parameters are:
+
+ parm:           clockmode:1=3Mhz579,2=3Mhz680,3=6Mhz (int)
+ parm:           boost:overclock boost percent 100 to 500 (int)
+ parm:           cdmode:Card detect mode 0=none, 1=CD, 2=!CD, 3=DSR, 4=!DSR, 5=CTS, 6=!CTS, 7=RING, 8=!RING (int)
+ parm:           xmas:xmas color enabled or not (bool)
+ parm:           debug:Debug enabled or not (bool)
+
+-  clockmode will provide 3 different base settings commonly adopted by
+   different software:
+ 	1. 3Mhz579
+	2. 3Mhz680
+	3. 6Mhz
+
+-  boost provide a way to overclock the reader ( my favorite :-)  )
+   For example to have best performance than a simple clockmode=3, try this:
+
+      modprobe boost=195
+
+   This will put the reader in a base of 3Mhz579 but boosted a 195 % !
+   the real clock will be now : 6979050 Hz ( 6Mhz979 ) and will increase
+   the speed to a score 10 to 20% better than the simple clockmode=3 !!!
+
+
+-  cdmode permit to setup the signal used to inform the userland ( ioctl answer )
+   if the card is present or not. Eight signals are possible.
+
+-  xmas is completely useless except for your eyes. This is one of my friend who was
+   so sad to have a nice device like the iuu without seeing all color range available.
+   So I have added this option to permit him to see a lot of color ( each activity change the color
+   and the frequency randomly )
+
+-  debug will produce a lot of debugging messages...
+
+
+ Last notes:
+
+ Don't worry about the serial settings, the serial emulation
+ is an abstraction, so use any speed or parity setting will
+ work. ( This will not change anything ).Later I will perhaps
+ use this settings to deduce de boost but is that feature
+ really necessary ?
+ The autodetect feature used is the serial CD. If that doesn't
+ work for your software, disable detection mechanism in it.
+
+
+ Have fun !
+
+ Alain Degreffe
+
+ eczema(at)ecze.com

drivers/usb/serial/Kconfig

@@ -282,6 +282,17 @@ config USB_SERIAL_IPW
 	  To compile this driver as a module, choose M here: the
 	  module will be called ipw.
 
+config USB_SERIAL_IUU
+	tristate "USB Infinity USB Unlimited Phoenix Driver (Experimental)"
+	depends on USB_SERIAL && EXPERIMENTAL
+	help
+	  Say Y here if you want to use a IUU in phoenix mode and get
+	  an extra ttyUSBx device. More information available on
+	  http://eczema.ecze.com/iuu_phoenix.html
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called iuu_phoenix.o
+
 config USB_SERIAL_KEYSPAN_PDA
 	tristate "USB Keyspan PDA Single Port Serial Driver"
 	depends on USB_SERIAL

drivers/usb/serial/Makefile

@@ -30,6 +30,7 @@ obj-$(CONFIG_USB_SERIAL_GARMIN)			+= garmin_gps.o
 obj-$(CONFIG_USB_SERIAL_HP4X)			+= hp4x.o
 obj-$(CONFIG_USB_SERIAL_IPAQ)			+= ipaq.o
 obj-$(CONFIG_USB_SERIAL_IPW)			+= ipw.o
+obj-$(CONFIG_USB_SERIAL_IUU)			+= iuu_phoenix.o
 obj-$(CONFIG_USB_SERIAL_IR)			+= ir-usb.o
 obj-$(CONFIG_USB_SERIAL_KEYSPAN)		+= keyspan.o
 obj-$(CONFIG_USB_SERIAL_KEYSPAN_PDA)		+= keyspan_pda.o

drivers/usb/serial/iuu_phoenix.h

+/*
+ * Infinity Unlimited USB Phoenix driver
+ *
+ * Copyright (C) 2007 Alain Degreffe (eczema@ecze.com)
+ *
+ *
+ * Original code taken from iuutool ( Copyright (C) 2006 Juan Carlos Borrás )
+ *
+ *	This program is free software; you can redistribute it and/or modify
+ *	it under the terms of the GNU General Public License as published by
+ *	the Free Software Foundation; either version 2 of the License, or
+ *	(at your option) any later version.
+ *
+ *  And tested with help of WB Electronics
+ *
+ */
+
+#define   IUU_USB_VENDOR_ID  0x104f
+#define   IUU_USB_PRODUCT_ID  0x0004
+#define   IUU_USB_OP_TIMEOUT  0x0200
+
+/* Programmer commands */
+
+#define IUU_NO_OPERATION   0x00
+#define IUU_GET_FIRMWARE_VERSION   0x01
+#define IUU_GET_PRODUCT_NAME   0x02
+#define IUU_GET_STATE_REGISTER   0x03
+#define IUU_SET_LED   0x04
+#define IUU_WAIT_MUS   0x05
+#define IUU_WAIT_MS   0x06
+#define IUU_GET_LOADER_VERSION   0x50
+#define IUU_RST_SET   0x52
+#define IUU_RST_CLEAR   0x53
+#define IUU_SET_VCC   0x59
+#define IUU_UART_ENABLE   0x49
+#define IUU_UART_DISABLE   0x4A
+#define IUU_UART_WRITE_I2C   0x4C
+#define IUU_UART_ESC   0x5E
+#define IUU_UART_TRAP   0x54
+#define IUU_UART_TRAP_BREAK   0x5B
+#define IUU_UART_RX   0x56
+#define IUU_AVR_ON   0x21
+#define IUU_AVR_OFF   0x22
+#define IUU_AVR_1CLK   0x23
+#define IUU_AVR_RESET   0x24
+#define IUU_AVR_RESET_PC   0x25
+#define IUU_AVR_INC_PC   0x26
+#define IUU_AVR_INCN_PC   0x27
+#define IUU_AVR_PREAD   0x29
+#define IUU_AVR_PREADN   0x2A
+#define IUU_AVR_PWRITE   0x28
+#define IUU_AVR_DREAD   0x2C
+#define IUU_AVR_DREADN   0x2D
+#define IUU_AVR_DWRITE   0x2B
+#define IUU_AVR_PWRITEN   0x2E
+#define IUU_EEPROM_ON   0x37
+#define IUU_EEPROM_OFF   0x38
+#define IUU_EEPROM_WRITE   0x39
+#define IUU_EEPROM_WRITEX   0x3A
+#define IUU_EEPROM_WRITE8   0x3B
+#define IUU_EEPROM_WRITE16   0x3C
+#define IUU_EEPROM_WRITEX32   0x3D
+#define IUU_EEPROM_WRITEX64   0x3E
+#define IUU_EEPROM_READ   0x3F
+#define IUU_EEPROM_READX   0x40
+#define IUU_EEPROM_BREAD   0x41
+#define IUU_EEPROM_BREADX   0x42
+#define IUU_PIC_CMD   0x0A
+#define IUU_PIC_CMD_LOAD   0x0B
+#define IUU_PIC_CMD_READ   0x0C
+#define IUU_PIC_ON   0x0D
+#define IUU_PIC_OFF   0x0E
+#define IUU_PIC_RESET   0x16
+#define IUU_PIC_INC_PC   0x0F
+#define IUU_PIC_INCN_PC   0x10
+#define IUU_PIC_PWRITE   0x11
+#define IUU_PIC_PREAD   0x12
+#define IUU_PIC_PREADN   0x13
+#define IUU_PIC_DWRITE   0x14
+#define IUU_PIC_DREAD   0x15
+#define IUU_UART_NOP   0x00
+#define IUU_UART_CHANGE   0x02
+#define IUU_UART_TX   0x04
+#define IUU_DELAY_MS   0x06
+
+#define IUU_OPERATION_OK   0x00
+#define IUU_DEVICE_NOT_FOUND   0x01
+#define IUU_INVALID_HANDLE   0x02
+#define IUU_INVALID_PARAMETER   0x03
+#define IUU_INVALID_voidERFACE   0x04
+#define IUU_INVALID_REQUEST_LENGTH   0x05
+#define IUU_UART_NOT_ENABLED   0x06
+#define IUU_WRITE_ERROR   0x07
+#define IUU_READ_ERROR   0x08
+#define IUU_TX_ERROR   0x09
+#define IUU_RX_ERROR   0x0A
+
+#define IUU_PARITY_NONE   0x00
+#define IUU_PARITY_EVEN   0x01
+#define IUU_PARITY_ODD   0x02
+#define IUU_PARITY_MARK   0x03
+#define IUU_PARITY_SPACE   0x04
+#define IUU_SC_INSERTED   0x01
+#define IUU_VERIFY_ERROR   0x02
+#define IUU_SIM_INSERTED   0x04
+#define IUU_TWO_STOP_BITS   0x00
+#define IUU_ONE_STOP_BIT   0x20
+#define IUU_BAUD_2400   0x0398
+#define IUU_BAUD_9600   0x0298
+#define IUU_BAUD_19200   0x0164
+#define IUU_BAUD_28800   0x0198
+#define IUU_BAUD_38400   0x01B2
+#define IUU_BAUD_57600   0x0030
+#define IUU_BAUD_115200   0x0098
+#define IUU_CLK_3579000   3579000
+#define IUU_CLK_3680000   3680000
+#define IUU_CLK_6000000   6000000
+#define IUU_FULLCARD_IN   0x01
+#define IUU_DEV_ERROR   0x02
+#define IUU_MINICARD_IN   0x04
+#define IUU_VCC_5V   0x00
+#define IUU_VCC_3V   0x01