Commit 61dac43e authored by David S. Miller's avatar David S. Miller

Merge branch 'bcmgenet'

Florian Fainelli says:

====================
net: bcmgenet: Wake-on-LAN and suspend fixes

This patch series fixes some mistakes that were introduced during the driver
changes adding support suspend/resume and Wake-on-LAN.
====================
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parents 8dff81e8 98bb7399
......@@ -739,7 +739,6 @@ static void bcmgenet_power_down(struct bcmgenet_priv *priv,
case GENET_POWER_PASSIVE:
/* Power down LED */
bcmgenet_mii_reset(priv->dev);
if (priv->hw_params->flags & GENET_HAS_EXT) {
reg = bcmgenet_ext_readl(priv, EXT_EXT_PWR_MGMT);
reg |= (EXT_PWR_DOWN_PHY |
......@@ -779,7 +778,9 @@ static void bcmgenet_power_up(struct bcmgenet_priv *priv,
}
bcmgenet_ext_writel(priv, reg, EXT_EXT_PWR_MGMT);
bcmgenet_mii_reset(priv->dev);
if (mode == GENET_POWER_PASSIVE)
bcmgenet_mii_reset(priv->dev);
}
/* ioctl handle special commands that are not present in ethtool. */
......@@ -1961,7 +1962,8 @@ static void bcmgenet_set_hw_addr(struct bcmgenet_priv *priv,
static int bcmgenet_wol_resume(struct bcmgenet_priv *priv)
{
/* From WOL-enabled suspend, switch to regular clock */
clk_disable_unprepare(priv->clk_wol);
if (priv->wolopts)
clk_disable_unprepare(priv->clk_wol);
phy_init_hw(priv->phydev);
/* Speed settings must be restored */
......@@ -2164,6 +2166,10 @@ static void bcmgenet_netif_stop(struct net_device *dev)
* disabled no new work will be scheduled.
*/
cancel_work_sync(&priv->bcmgenet_irq_work);
priv->old_pause = -1;
priv->old_link = -1;
priv->old_duplex = -1;
}
static int bcmgenet_close(struct net_device *dev)
......@@ -2533,6 +2539,13 @@ static int bcmgenet_probe(struct platform_device *pdev)
priv->pdev = pdev;
priv->version = (enum bcmgenet_version)of_id->data;
priv->clk = devm_clk_get(&priv->pdev->dev, "enet");
if (IS_ERR(priv->clk))
dev_warn(&priv->pdev->dev, "failed to get enet clock\n");
if (!IS_ERR(priv->clk))
clk_prepare_enable(priv->clk);
bcmgenet_set_hw_params(priv);
/* Mii wait queue */
......@@ -2541,17 +2554,10 @@ static int bcmgenet_probe(struct platform_device *pdev)
priv->rx_buf_len = RX_BUF_LENGTH;
INIT_WORK(&priv->bcmgenet_irq_work, bcmgenet_irq_task);
priv->clk = devm_clk_get(&priv->pdev->dev, "enet");
if (IS_ERR(priv->clk))
dev_warn(&priv->pdev->dev, "failed to get enet clock\n");
priv->clk_wol = devm_clk_get(&priv->pdev->dev, "enet-wol");
if (IS_ERR(priv->clk_wol))
dev_warn(&priv->pdev->dev, "failed to get enet-wol clock\n");
if (!IS_ERR(priv->clk))
clk_prepare_enable(priv->clk);
err = reset_umac(priv);
if (err)
goto err_clk_disable;
......@@ -2611,6 +2617,8 @@ static int bcmgenet_suspend(struct device *d)
bcmgenet_netif_stop(dev);
phy_suspend(priv->phydev);
netif_device_detach(dev);
/* Disable MAC receive */
......@@ -2661,9 +2669,7 @@ static int bcmgenet_resume(struct device *d)
if (ret)
goto out_clk_disable;
if (priv->wolopts)
ret = bcmgenet_wol_resume(priv);
ret = bcmgenet_wol_resume(priv);
if (ret)
goto out_clk_disable;
......@@ -2678,6 +2684,9 @@ static int bcmgenet_resume(struct device *d)
bcmgenet_ext_writel(priv, reg, EXT_EXT_PWR_MGMT);
}
if (priv->wolopts)
bcmgenet_power_up(priv, GENET_POWER_WOL_MAGIC);
/* Disable RX/TX DMA and flush TX queues */
dma_ctrl = bcmgenet_dma_disable(priv);
......@@ -2693,6 +2702,8 @@ static int bcmgenet_resume(struct device *d)
netif_device_attach(dev);
phy_resume(priv->phydev);
bcmgenet_netif_start(dev);
return 0;
......
......@@ -129,7 +129,10 @@ static void bcmgenet_mii_setup(struct net_device *dev)
cmd_bits |= CMD_RX_PAUSE_IGNORE | CMD_TX_PAUSE_IGNORE;
}
if (status_changed) {
if (!status_changed)
return;
if (phydev->link) {
reg = bcmgenet_umac_readl(priv, UMAC_CMD);
reg &= ~((CMD_SPEED_MASK << CMD_SPEED_SHIFT) |
CMD_HD_EN |
......@@ -137,8 +140,9 @@ static void bcmgenet_mii_setup(struct net_device *dev)
reg |= cmd_bits;
bcmgenet_umac_writel(priv, reg, UMAC_CMD);
phy_print_status(phydev);
}
phy_print_status(phydev);
}
void bcmgenet_mii_reset(struct net_device *dev)
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment