arm64: dts: qcom: sm8650-qrd: add USB-C Altmode Support

Add the necessary nodes to support the USB-C Altmode path by
adding the following
- WCD939x USBSS Mux I2C device
- nb7vpq904m Redriver I2C device
- Port/Endpoint graph links bettween PMIC-Glink, Mux, Redriver and USB PHY nodes.

WCD939x USBSS port 2 Path to Codec will be added later when Audio support
is added.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240123-topic-sm8650-upstream-altmode-v3-1-300a5ac80e1e@linaro.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

arch/arm64/boot/dts/qcom/sm8650-qrd.dts

@@ -77,9 +77,17 @@ port@1 {
 					reg = <1>;
 
 					pmic_glink_ss_in: endpoint {
-						remote-endpoint = <&usb_1_dwc3_ss>;
+						remote-endpoint = <&redriver_ss_out>;
 					};
 				};
+
+				port@2 {
+					reg = <2>;
+
+					pmic_glink_sbu: endpoint {
+						remote-endpoint = <&wcd_usbss_sbu_mux>;
+				    };
+				};
 			};
 		};
 	};
@@ -446,6 +454,70 @@ &gpi_dma1 {
 	status = "okay";
 };
 
+&i2c3 {
+       status = "okay";
+
+       wcd_usbss: typec-mux@e {
+		compatible = "qcom,wcd9395-usbss", "qcom,wcd9390-usbss";
+		reg = <0xe>;
+
+		vdd-supply = <&vreg_l15b_1p8>;
+		reset-gpios = <&tlmm 152 GPIO_ACTIVE_HIGH>;
+
+		mode-switch;
+		orientation-switch;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				wcd_usbss_sbu_mux: endpoint {
+					remote-endpoint = <&pmic_glink_sbu>;
+				};
+			};
+		};
+       };
+};
+
+&i2c6 {
+	status = "okay";
+
+	typec-mux@1c {
+		compatible = "onnn,nb7vpq904m";
+		reg = <0x1c>;
+
+		vcc-supply = <&vreg_l15b_1p8>;
+
+		retimer-switch;
+		orientation-switch;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				redriver_ss_out: endpoint {
+					remote-endpoint = <&pmic_glink_ss_in>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				redriver_ss_in: endpoint {
+					data-lanes = <3 2 1 0>;
+					remote-endpoint = <&usb_dp_qmpphy_out>;
+				};
+			};
+		};
+	};
+};
+
 &ipa {
 	qcom,gsi-loader = "self";
 	memory-region = <&ipa_fw_mem>;
@@ -495,6 +567,15 @@ &mdss_dsi0_phy {
 	status = "okay";
 };
 
+&mdss_dp0 {
+	status = "okay";
+};
+
+&mdss_dp0_out {
+	data-lanes = <0 1>;
+	remote-endpoint = <&usb_dp_qmpphy_dp_in>;
+};
+
 &mdss_mdp {
 	status = "okay";
 };
@@ -600,6 +681,11 @@ &pmk8550_rtc {
 	status = "okay";
 };
 
+&qup_i2c3_data_clk {
+	/* Use internal I2C pull-up */
+	bias-pull-up = <2200>;
+};
+
 &qupv3_id_0 {
 	status = "okay";
 };
@@ -787,7 +873,7 @@ &usb_1_dwc3_hs {
 };
 
 &usb_1_dwc3_ss {
-	remote-endpoint = <&pmic_glink_ss_in>;
+	remote-endpoint = <&usb_dp_qmpphy_usb_ss_in>;
 };
 
 &usb_1_hsphy {
@@ -803,9 +889,23 @@ &usb_dp_qmpphy {
 	vdda-phy-supply = <&vreg_l3i_1p2>;
 	vdda-pll-supply = <&vreg_l3g_0p91>;
 
+	orientation-switch;
+
 	status = "okay";
 };
 
+&usb_dp_qmpphy_dp_in {
+	remote-endpoint = <&mdss_dp0_out>;
+};
+
+&usb_dp_qmpphy_out {
+	remote-endpoint = <&redriver_ss_in>;
+};
+
+&usb_dp_qmpphy_usb_ss_in {
+	remote-endpoint = <&usb_1_dwc3_ss>;
+};
+
 &xo_board {
 	clock-frequency = <76800000>;
 };