spi: Header and core clean up and refactoring

Merge series from Andy Shevchenko <andriy.shevchenko@linux.intel.com>:

Various cleanups and refactorings of the SPI header and core parts
united in a single series. It also touches drivers under SPI subsystem
folder on the pure renaming purposes of some constants.

No functional change intended.

drivers/spi/spi-amd.c

@@ -404,7 +404,7 @@ static int amd_spi_probe(struct platform_device *pdev)
 	master->bus_num = 0;
 	master->num_chipselect = 4;
 	master->mode_bits = 0;
-	master->flags = SPI_MASTER_HALF_DUPLEX;
+	master->flags = SPI_CONTROLLER_HALF_DUPLEX;
 	master->max_speed_hz = AMD_SPI_MAX_HZ;
 	master->min_speed_hz = AMD_SPI_MIN_HZ;
 	master->setup = amd_spi_master_setup;

drivers/spi/spi-at91-usart.c

@@ -527,7 +527,7 @@ static int at91_usart_spi_probe(struct platform_device *pdev)
 	controller->dev.of_node = pdev->dev.parent->of_node;
 	controller->bits_per_word_mask = SPI_BPW_MASK(8);
 	controller->setup = at91_usart_spi_setup;
-	controller->flags = SPI_MASTER_MUST_RX | SPI_MASTER_MUST_TX;
+	controller->flags = SPI_CONTROLLER_MUST_RX | SPI_CONTROLLER_MUST_TX;
 	controller->transfer_one = at91_usart_spi_transfer_one;
 	controller->prepare_message = at91_usart_spi_prepare_message;
 	controller->unprepare_message = at91_usart_spi_unprepare_message;

drivers/spi/spi-ath79.c

@@ -185,7 +185,7 @@ static int ath79_spi_probe(struct platform_device *pdev)
 
 	host->use_gpio_descriptors = true;
 	host->bits_per_word_mask = SPI_BPW_RANGE_MASK(1, 32);
-	host->flags = SPI_MASTER_GPIO_SS;
+	host->flags = SPI_CONTROLLER_GPIO_SS;
 	host->num_chipselect = 3;
 	host->mem_ops = &ath79_mem_ops;
 

drivers/spi/spi-atmel.c

@@ -1471,8 +1471,8 @@ static int atmel_spi_probe(struct platform_device *pdev)
 	host->bus_num = pdev->id;
 	host->num_chipselect = 4;
 	host->setup = atmel_spi_setup;
-	host->flags = (SPI_MASTER_MUST_RX | SPI_MASTER_MUST_TX |
-			SPI_MASTER_GPIO_SS);
+	host->flags = (SPI_CONTROLLER_MUST_RX | SPI_CONTROLLER_MUST_TX |
+			SPI_CONTROLLER_GPIO_SS);
 	host->transfer_one = atmel_spi_one_transfer;
 	host->set_cs = atmel_spi_set_cs;
 	host->cleanup = atmel_spi_cleanup;

drivers/spi/spi-bitbang-txrx.h

@@ -57,7 +57,7 @@ bitbang_txrx_be_cpha0(struct spi_device *spi,
 	for (word <<= (32 - bits); likely(bits); bits--) {
 
 		/* setup MSB (to slave) on trailing edge */
-		if ((flags & SPI_MASTER_NO_TX) == 0) {
+		if ((flags & SPI_CONTROLLER_NO_TX) == 0) {
 			if ((word & (1 << 31)) != oldbit) {
 				setmosi(spi, word & (1 << 31));
 				oldbit = word & (1 << 31);
@@ -70,7 +70,7 @@ bitbang_txrx_be_cpha0(struct spi_device *spi,
 
 		/* sample MSB (from slave) on leading edge */
 		word <<= 1;
-		if ((flags & SPI_MASTER_NO_RX) == 0)
+		if ((flags & SPI_CONTROLLER_NO_RX) == 0)
 			word |= getmiso(spi);
 		setsck(spi, cpol);
 	}
@@ -90,7 +90,7 @@ bitbang_txrx_be_cpha1(struct spi_device *spi,
 
 		/* setup MSB (to slave) on leading edge */
 		setsck(spi, !cpol);
-		if ((flags & SPI_MASTER_NO_TX) == 0) {
+		if ((flags & SPI_CONTROLLER_NO_TX) == 0) {
 			if ((word & (1 << 31)) != oldbit) {
 				setmosi(spi, word & (1 << 31));
 				oldbit = word & (1 << 31);
@@ -103,7 +103,7 @@ bitbang_txrx_be_cpha1(struct spi_device *spi,
 
 		/* sample MSB (from slave) on trailing edge */
 		word <<= 1;
-		if ((flags & SPI_MASTER_NO_RX) == 0)
+		if ((flags & SPI_CONTROLLER_NO_RX) == 0)
 			word |= getmiso(spi);
 	}
 	return word;
@@ -122,7 +122,7 @@ bitbang_txrx_le_cpha0(struct spi_device *spi,
 	for (; likely(bits); bits--) {
 
 		/* setup LSB (to slave) on trailing edge */
-		if ((flags & SPI_MASTER_NO_TX) == 0) {
+		if ((flags & SPI_CONTROLLER_NO_TX) == 0) {
 			if ((word & 1) != oldbit) {
 				setmosi(spi, word & 1);
 				oldbit = word & 1;
@@ -135,7 +135,7 @@ bitbang_txrx_le_cpha0(struct spi_device *spi,
 
 		/* sample LSB (from slave) on leading edge */
 		word >>= 1;
-		if ((flags & SPI_MASTER_NO_RX) == 0)
+		if ((flags & SPI_CONTROLLER_NO_RX) == 0)
 			word |= getmiso(spi) << rxbit;
 		setsck(spi, cpol);
 	}
@@ -156,7 +156,7 @@ bitbang_txrx_le_cpha1(struct spi_device *spi,
 
 		/* setup LSB (to slave) on leading edge */
 		setsck(spi, !cpol);
-		if ((flags & SPI_MASTER_NO_TX) == 0) {
+		if ((flags & SPI_CONTROLLER_NO_TX) == 0) {
 			if ((word & 1) != oldbit) {
 				setmosi(spi, word & 1);
 				oldbit = word & 1;
@@ -169,7 +169,7 @@ bitbang_txrx_le_cpha1(struct spi_device *spi,
 
 		/* sample LSB (from slave) on trailing edge */
 		word >>= 1;
-		if ((flags & SPI_MASTER_NO_RX) == 0)
+		if ((flags & SPI_CONTROLLER_NO_RX) == 0)
 			word |= getmiso(spi) << rxbit;
 	}
 	return word;

drivers/spi/spi-bitbang.c

@@ -248,7 +248,7 @@ static int spi_bitbang_bufs(struct spi_device *spi, struct spi_transfer *t)
 	if (spi->mode & SPI_3WIRE) {
 		unsigned flags;
 
-		flags = t->tx_buf ? SPI_MASTER_NO_RX : SPI_MASTER_NO_TX;
+		flags = t->tx_buf ? SPI_CONTROLLER_NO_RX : SPI_CONTROLLER_NO_TX;
 		return cs->txrx_bufs(spi, cs->txrx_word, nsecs, t, flags);
 	}
 	return cs->txrx_bufs(spi, cs->txrx_word, nsecs, t, 0);
@@ -349,11 +349,11 @@ int spi_bitbang_init(struct spi_bitbang *bitbang)
 	/*
 	 * We only need the chipselect callback if we are actually using it.
 	 * If we just use GPIO descriptors, it is surplus. If the
-	 * SPI_MASTER_GPIO_SS flag is set, we always need to call the
+	 * SPI_CONTROLLER_GPIO_SS flag is set, we always need to call the
 	 * driver-specific chipselect routine.
 	 */
 	custom_cs = (!master->use_gpio_descriptors ||
-		     (master->flags & SPI_MASTER_GPIO_SS));
+		     (master->flags & SPI_CONTROLLER_GPIO_SS));
 
 	if (custom_cs && !bitbang->chipselect)
 		return -EINVAL;
@@ -371,7 +371,7 @@ int spi_bitbang_init(struct spi_bitbang *bitbang)
 	master->transfer_one = spi_bitbang_transfer_one;
 	/*
 	 * When using GPIO descriptors, the ->set_cs() callback doesn't even
-	 * get called unless SPI_MASTER_GPIO_SS is set.
+	 * get called unless SPI_CONTROLLER_GPIO_SS is set.
 	 */
 	if (custom_cs)
 		master->set_cs = spi_bitbang_set_cs;

drivers/spi/spi-cavium-thunderx.c

@@ -64,7 +64,7 @@ static int thunderx_spi_probe(struct pci_dev *pdev,
 		p->sys_freq = SYS_FREQ_DEFAULT;
 	dev_info(dev, "Set system clock to %u\n", p->sys_freq);
 
-	master->flags = SPI_MASTER_HALF_DUPLEX;
+	master->flags = SPI_CONTROLLER_HALF_DUPLEX;
 	master->num_chipselect = 4;
 	master->mode_bits = SPI_CPHA | SPI_CPOL | SPI_CS_HIGH |
 			    SPI_LSB_FIRST | SPI_3WIRE;

drivers/spi/spi-davinci.c

@@ -930,7 +930,7 @@ static int davinci_spi_probe(struct platform_device *pdev)
 	master->bus_num = pdev->id;
 	master->num_chipselect = pdata->num_chipselect;
 	master->bits_per_word_mask = SPI_BPW_RANGE_MASK(2, 16);
-	master->flags = SPI_MASTER_MUST_RX | SPI_MASTER_GPIO_SS;
+	master->flags = SPI_CONTROLLER_MUST_RX | SPI_CONTROLLER_GPIO_SS;
 	master->setup = davinci_spi_setup;
 	master->cleanup = davinci_spi_cleanup;
 	master->can_dma = davinci_spi_can_dma;

drivers/spi/spi-dw-core.c

@@ -932,7 +932,7 @@ int dw_spi_add_host(struct device *dev, struct dw_spi *dws)
 	if (dws->mem_ops.exec_op)
 		master->mem_ops = &dws->mem_ops;
 	master->max_speed_hz = dws->max_freq;
-	master->flags = SPI_MASTER_GPIO_SS;
+	master->flags = SPI_CONTROLLER_GPIO_SS;
 	master->auto_runtime_pm = true;
 
 	/* Get default rx sample delay */

drivers/spi/spi-falcon.c

@@ -401,7 +401,7 @@ static int falcon_sflash_probe(struct platform_device *pdev)
 	priv->master = master;
 
 	master->mode_bits = SPI_MODE_3;
-	master->flags = SPI_MASTER_HALF_DUPLEX;
+	master->flags = SPI_CONTROLLER_HALF_DUPLEX;
 	master->setup = falcon_sflash_setup;
 	master->transfer_one_message = falcon_sflash_xfer_one;
 	master->dev.of_node = pdev->dev.of_node;

drivers/spi/spi-fsl-lpspi.c

@@ -856,7 +856,7 @@ static int fsl_lpspi_probe(struct platform_device *pdev)
 	controller->prepare_transfer_hardware = lpspi_prepare_xfer_hardware;
 	controller->unprepare_transfer_hardware = lpspi_unprepare_xfer_hardware;
 	controller->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
-	controller->flags = SPI_MASTER_MUST_RX | SPI_MASTER_MUST_TX;
+	controller->flags = SPI_CONTROLLER_MUST_RX | SPI_CONTROLLER_MUST_TX;
 	controller->dev.of_node = pdev->dev.of_node;
 	controller->bus_num = pdev->id;
 	controller->num_chipselect = fsl_lpspi->num_cs;

drivers/spi/spi-gpio.c

@@ -170,7 +170,7 @@ static u32 spi_gpio_txrx_word_mode3(struct spi_device *spi,
 
 /*
  * These functions do not call setmosi or getmiso if respective flag
- * (SPI_MASTER_NO_RX or SPI_MASTER_NO_TX) is set, so they are safe to
+ * (SPI_CONTROLLER_NO_RX or SPI_CONTROLLER_NO_TX) is set, so they are safe to
  * call when such pin is not present or defined in the controller.
  * A separate set of callbacks is defined to get highest possible
  * speed in the generic case (when both MISO and MOSI lines are
@@ -416,11 +416,11 @@ static int spi_gpio_probe(struct platform_device *pdev)
 	if (!spi_gpio->mosi) {
 		/* HW configuration without MOSI pin
 		 *
-		 * No setting SPI_MASTER_NO_RX here - if there is only
+		 * No setting SPI_CONTROLLER_NO_RX here - if there is only
 		 * a MOSI pin connected the host can still do RX by
 		 * changing the direction of the line.
 		 */
-		master->flags = SPI_MASTER_NO_TX;
+		master->flags = SPI_CONTROLLER_NO_TX;
 	}
 
 	master->bus_num = pdev->id;
@@ -434,11 +434,11 @@ static int spi_gpio_probe(struct platform_device *pdev)
 	 * line, that we need to do on selection. This makes the local
 	 * callback for chipselect always get called.
 	 */
-	master->flags |= SPI_MASTER_GPIO_SS;
+	master->flags |= SPI_CONTROLLER_GPIO_SS;
 	bb->chipselect = spi_gpio_chipselect;
 	bb->set_line_direction = spi_gpio_set_direction;
 
-	if (master->flags & SPI_MASTER_NO_TX) {
+	if (master->flags & SPI_CONTROLLER_NO_TX) {
 		bb->txrx_word[SPI_MODE_0] = spi_gpio_spec_txrx_word_mode0;
 		bb->txrx_word[SPI_MODE_1] = spi_gpio_spec_txrx_word_mode1;
 		bb->txrx_word[SPI_MODE_2] = spi_gpio_spec_txrx_word_mode2;

drivers/spi/spi-imx.c

@@ -1784,7 +1784,7 @@ static int spi_imx_probe(struct platform_device *pdev)
 
 	if (is_imx51_ecspi(spi_imx) || is_imx53_ecspi(spi_imx)) {
 		controller->max_native_cs = 4;
-		controller->flags |= SPI_MASTER_GPIO_SS;
+		controller->flags |= SPI_CONTROLLER_GPIO_SS;
 	}
 
 	spi_imx->spi_drctl = spi_drctl;

drivers/spi/spi-lp8841-rtc.c

@@ -75,14 +75,14 @@ bitbang_txrx_be_cpha0_lsb(struct spi_lp8841_rtc *data,
 	for (; likely(bits); bits--) {
 
 		/* setup LSB (to slave) on leading edge */
-		if ((flags & SPI_MASTER_NO_TX) == 0)
+		if ((flags & SPI_CONTROLLER_NO_TX) == 0)
 			setmosi(data, (word & 1));
 
 		usleep_range(usecs, usecs + 1);	/* T(setup) */
 
 		/* sample LSB (from slave) on trailing edge */
 		word >>= 1;
-		if ((flags & SPI_MASTER_NO_RX) == 0)
+		if ((flags & SPI_CONTROLLER_NO_RX) == 0)
 			word |= (getmiso(data) << 31);
 
 		setsck(data, !cpol);
@@ -113,7 +113,7 @@ spi_lp8841_rtc_transfer_one(struct spi_master *master,
 		while (likely(count > 0)) {
 			word = *tx++;
 			bitbang_txrx_be_cpha0_lsb(data, 1, 0,
-					SPI_MASTER_NO_RX, word, 8);
+					SPI_CONTROLLER_NO_RX, word, 8);
 			count--;
 		}
 	} else if (rx) {
@@ -121,7 +121,7 @@ spi_lp8841_rtc_transfer_one(struct spi_master *master,
 		writeb(data->state, data->iomem);
 		while (likely(count > 0)) {
 			word = bitbang_txrx_be_cpha0_lsb(data, 1, 0,
-					SPI_MASTER_NO_TX, word, 8);
+					SPI_CONTROLLER_NO_TX, word, 8);
 			*rx++ = word;
 			count--;
 		}
@@ -191,7 +191,7 @@ spi_lp8841_rtc_probe(struct platform_device *pdev)
 		return -ENOMEM;
 	platform_set_drvdata(pdev, master);
 
-	master->flags = SPI_MASTER_HALF_DUPLEX;
+	master->flags = SPI_CONTROLLER_HALF_DUPLEX;
 	master->mode_bits = SPI_CS_HIGH | SPI_3WIRE | SPI_LSB_FIRST;
 
 	master->bus_num = pdev->id;

drivers/spi/spi-meson-spicc.c

@@ -864,7 +864,7 @@ static int meson_spicc_probe(struct platform_device *pdev)
 				     SPI_BPW_MASK(24) |
 				     SPI_BPW_MASK(16) |
 				     SPI_BPW_MASK(8);
-	master->flags = (SPI_MASTER_MUST_RX | SPI_MASTER_MUST_TX);
+	master->flags = (SPI_CONTROLLER_MUST_RX | SPI_CONTROLLER_MUST_TX);
 	master->min_speed_hz = spicc->data->min_speed_hz;
 	master->max_speed_hz = spicc->data->max_speed_hz;
 	master->setup = meson_spicc_setup;

drivers/spi/spi-mt65xx.c

@@ -1142,7 +1142,7 @@ static int mtk_spi_probe(struct platform_device *pdev)
 		master->mode_bits |= SPI_CS_HIGH;
 
 	if (mdata->dev_comp->must_tx)
-		master->flags = SPI_MASTER_MUST_TX;
+		master->flags = SPI_CONTROLLER_MUST_TX;
 	if (mdata->dev_comp->ipm_design)
 		master->mode_bits |= SPI_LOOP | SPI_RX_DUAL | SPI_TX_DUAL |
 				     SPI_RX_QUAD | SPI_TX_QUAD;

drivers/spi/spi-mxs.c

@@ -572,7 +572,7 @@ static int mxs_spi_probe(struct platform_device *pdev)
 	master->mode_bits = SPI_CPOL | SPI_CPHA;
 	master->num_chipselect = 3;
 	master->dev.of_node = np;
-	master->flags = SPI_MASTER_HALF_DUPLEX;
+	master->flags = SPI_CONTROLLER_HALF_DUPLEX;
 	master->auto_runtime_pm = true;
 
 	spi = spi_master_get_devdata(master);

drivers/spi/spi-omap-uwire.c

@@ -486,7 +486,7 @@ static int uwire_probe(struct platform_device *pdev)
 	/* the spi->mode bits understood by this driver: */
 	master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
 	master->bits_per_word_mask = SPI_BPW_RANGE_MASK(1, 16);
-	master->flags = SPI_MASTER_HALF_DUPLEX;
+	master->flags = SPI_CONTROLLER_HALF_DUPLEX;
 
 	master->bus_num = 2;	/* "official" */
 	master->num_chipselect = 4;

drivers/spi/spi-orion.c

@@ -677,7 +677,7 @@ static int orion_spi_probe(struct platform_device *pdev)
 	master->bits_per_word_mask = SPI_BPW_MASK(8) | SPI_BPW_MASK(16);
 	master->auto_runtime_pm = true;
 	master->use_gpio_descriptors = true;
-	master->flags = SPI_MASTER_GPIO_SS;
+	master->flags = SPI_CONTROLLER_GPIO_SS;
 
 	platform_set_drvdata(pdev, master);
 

drivers/spi/spi-pci1xxxx.c

@@ -365,7 +365,7 @@ static int pci1xxxx_spi_probe(struct pci_dev *pdev, const struct pci_device_id *
 		spi_host->bits_per_word_mask = SPI_BPW_MASK(8);
 		spi_host->max_speed_hz = PCI1XXXX_SPI_MAX_CLOCK_HZ;
 		spi_host->min_speed_hz = PCI1XXXX_SPI_MIN_CLOCK_HZ;
-		spi_host->flags = SPI_MASTER_MUST_TX;
+		spi_host->flags = SPI_CONTROLLER_MUST_TX;
 		spi_master_set_devdata(spi_host, spi_sub_ptr);
 		ret = devm_spi_register_master(dev, spi_host);
 		if (ret)

drivers/spi/spi-pic32-sqi.c

@@ -648,7 +648,7 @@ static int pic32_sqi_probe(struct platform_device *pdev)
 	master->dev.of_node	= pdev->dev.of_node;
 	master->mode_bits	= SPI_MODE_3 | SPI_MODE_0 | SPI_TX_DUAL |
 				  SPI_RX_DUAL | SPI_TX_QUAD | SPI_RX_QUAD;
-	master->flags		= SPI_MASTER_HALF_DUPLEX;
+	master->flags		= SPI_CONTROLLER_HALF_DUPLEX;
 	master->can_dma		= pic32_sqi_can_dma;
 	master->bits_per_word_mask	= SPI_BPW_RANGE_MASK(8, 32);
 	master->transfer_one_message	= pic32_sqi_one_message;

drivers/spi/spi-pic32.c

@@ -773,7 +773,7 @@ static int pic32_spi_probe(struct platform_device *pdev)
 	master->max_speed_hz	= clk_get_rate(pic32s->clk);
 	master->setup		= pic32_spi_setup;
 	master->cleanup		= pic32_spi_cleanup;
-	master->flags		= SPI_MASTER_MUST_TX | SPI_MASTER_MUST_RX;
+	master->flags		= SPI_CONTROLLER_MUST_TX | SPI_CONTROLLER_MUST_RX;
 	master->bits_per_word_mask	= SPI_BPW_MASK(8) | SPI_BPW_MASK(16) |
 					  SPI_BPW_MASK(32);
 	master->transfer_one		= pic32_spi_one_transfer;

drivers/spi/spi-qcom-qspi.c

@@ -724,7 +724,7 @@ static int qcom_qspi_probe(struct platform_device *pdev)
 	master->mode_bits = SPI_MODE_0 |
 			    SPI_TX_DUAL | SPI_RX_DUAL |
 			    SPI_TX_QUAD | SPI_RX_QUAD;
-	master->flags = SPI_MASTER_HALF_DUPLEX;
+	master->flags = SPI_CONTROLLER_HALF_DUPLEX;
 	master->prepare_message = qcom_qspi_prepare_message;
 	master->transfer_one = qcom_qspi_transfer_one;
 	master->handle_err = qcom_qspi_handle_err;

drivers/spi/spi-rb4xx.c

@@ -156,7 +156,7 @@ static int rb4xx_spi_probe(struct platform_device *pdev)
 	master->num_chipselect = 3;
 	master->mode_bits = SPI_TX_DUAL;
 	master->bits_per_word_mask = SPI_BPW_MASK(8);
-	master->flags = SPI_MASTER_MUST_TX;
+	master->flags = SPI_CONTROLLER_MUST_TX;
 	master->transfer_one = rb4xx_transfer_one;
 	master->set_cs = rb4xx_set_cs;
 

drivers/spi/spi-rockchip-sfc.c

@@ -565,7 +565,7 @@ static int rockchip_sfc_probe(struct platform_device *pdev)
 	if (!master)
 		return -ENOMEM;
 
-	master->flags = SPI_MASTER_HALF_DUPLEX;
+	master->flags = SPI_CONTROLLER_HALF_DUPLEX;
 	master->mem_ops = &rockchip_sfc_mem_ops;
 	master->dev.of_node = pdev->dev.of_node;
 	master->mode_bits = SPI_TX_QUAD | SPI_TX_DUAL | SPI_RX_QUAD | SPI_RX_DUAL;

drivers/spi/spi-rockchip.c

@@ -858,7 +858,7 @@ static int rockchip_spi_probe(struct platform_device *pdev)
 		ctlr->mode_bits |= SPI_NO_CS;
 		ctlr->slave_abort = rockchip_spi_slave_abort;
 	} else {
-		ctlr->flags = SPI_MASTER_GPIO_SS;
+		ctlr->flags = SPI_CONTROLLER_GPIO_SS;
 		ctlr->max_native_cs = ROCKCHIP_SPI_MAX_CS_NUM;
 		/*
 		 * rk spi0 has two native cs, spi1..5 one cs only

drivers/spi/spi-sifive.c

@@ -379,7 +379,7 @@ static int sifive_spi_probe(struct platform_device *pdev)
 	 * we need to "left-align" the bits (unless SPI_LSB_FIRST)
 	 */
 	master->bits_per_word_mask = SPI_BPW_MASK(8);
-	master->flags = SPI_CONTROLLER_MUST_TX | SPI_MASTER_GPIO_SS;
+	master->flags = SPI_CONTROLLER_MUST_TX | SPI_CONTROLLER_GPIO_SS;
 	master->prepare_message = sifive_spi_prepare_message;
 	master->set_cs = sifive_spi_set_cs;
 	master->transfer_one = sifive_spi_transfer_one;

drivers/spi/spi-slave-mt27xx.c

@@ -414,7 +414,7 @@ static int mtk_spi_slave_probe(struct platform_device *pdev)
 	mdata->dev_comp = of_id->data;
 
 	if (mdata->dev_comp->must_rx)
-		ctlr->flags = SPI_MASTER_MUST_RX;
+		ctlr->flags = SPI_CONTROLLER_MUST_RX;
 
 	platform_set_drvdata(pdev, ctlr);
 

drivers/spi/spi-sprd-adi.c

@@ -580,7 +580,7 @@ static int sprd_adi_probe(struct platform_device *pdev)
 	ctlr->dev.of_node = pdev->dev.of_node;
 	ctlr->bus_num = pdev->id;
 	ctlr->num_chipselect = num_chipselect;
-	ctlr->flags = SPI_MASTER_HALF_DUPLEX;
+	ctlr->flags = SPI_CONTROLLER_HALF_DUPLEX;
 	ctlr->bits_per_word_mask = 0;
 	ctlr->transfer_one = sprd_adi_transfer_one;
 

drivers/spi/spi-stm32.c

@@ -1753,7 +1753,7 @@ static const struct stm32_spi_cfg stm32f4_spi_cfg = {
 	.baud_rate_div_max = STM32F4_SPI_BR_DIV_MAX,
 	.has_fifo = false,
 	.has_device_mode = false,
-	.flags = SPI_MASTER_MUST_TX,
+	.flags = SPI_CONTROLLER_MUST_TX,
 };
 
 static const struct stm32_spi_cfg stm32h7_spi_cfg = {

drivers/spi/spi-ti-qspi.c

@@ -770,7 +770,7 @@ static int ti_qspi_probe(struct platform_device *pdev)
 
 	master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_RX_DUAL | SPI_RX_QUAD;
 
-	master->flags = SPI_MASTER_HALF_DUPLEX;
+	master->flags = SPI_CONTROLLER_HALF_DUPLEX;
 	master->setup = ti_qspi_setup;
 	master->auto_runtime_pm = true;
 	master->transfer_one_message = ti_qspi_start_transfer_one;

drivers/spi/spi-xcomm.c

@@ -218,7 +218,7 @@ static int spi_xcomm_probe(struct i2c_client *i2c)
 	master->num_chipselect = 16;
 	master->mode_bits = SPI_CPHA | SPI_CPOL | SPI_3WIRE;
 	master->bits_per_word_mask = SPI_BPW_MASK(8);
-	master->flags = SPI_MASTER_HALF_DUPLEX;
+	master->flags = SPI_CONTROLLER_HALF_DUPLEX;
 	master->transfer_one_message = spi_xcomm_transfer_one;
 	master->dev.of_node = i2c->dev.of_node;
 	i2c_set_clientdata(i2c, master);

drivers/spi/spi-xtensa-xtfpga.c

@@ -87,7 +87,7 @@ static int xtfpga_spi_probe(struct platform_device *pdev)
 	if (!master)
 		return -ENOMEM;
 
-	master->flags = SPI_MASTER_NO_RX;
+	master->flags = SPI_CONTROLLER_NO_RX;
 	master->bits_per_word_mask = SPI_BPW_RANGE_MASK(1, 16);
 	master->bus_num = pdev->dev.id;
 	master->dev.of_node = pdev->dev.of_node;

include/trace/events/spi.h

@@ -167,7 +167,7 @@ TRACE_EVENT(spi_message_done,
 );
 
 /*
- * consider a buffer valid if non-NULL and if it doesn't match the dummy buffer
+ * Consider a buffer valid if non-NULL and if it doesn't match the dummy buffer
  * that only exist to work with controllers that have SPI_CONTROLLER_MUST_TX or
  * SPI_CONTROLLER_MUST_RX.
  */