Commit 6a00d0dd authored by Andre Przywara's avatar Andre Przywara Committed by David S. Miller

net: axienet: Wrap DMA pointer writes to prepare for 64 bit

Newer versions of the Xilink DMA IP support busses with more than 32
address bits, by introducing an MSB word for the registers holding DMA
pointers (tail/current, RX/TX descriptor addresses).
On IP configured for more than 32 bits, it is also *required* to write
both words, to let the IP recognise this as a start condition for an
MM2S request, for instance.

Wrap the DMA pointer writes with a separate function, to add this
functionality later. For now we stick to the lower 32 bits.
Signed-off-by: default avatarAndre Przywara <andre.przywara@arm.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent 2a9b65ea
......@@ -147,6 +147,12 @@ static inline void axienet_dma_out32(struct axienet_local *lp,
iowrite32(value, lp->dma_regs + reg);
}
static void axienet_dma_out_addr(struct axienet_local *lp, off_t reg,
dma_addr_t addr)
{
axienet_dma_out32(lp, reg, lower_32_bits(addr));
}
/**
* axienet_dma_bd_release - Release buffer descriptor rings
* @ndev: Pointer to the net_device structure
......@@ -285,18 +291,18 @@ static int axienet_dma_bd_init(struct net_device *ndev)
/* Populate the tail pointer and bring the Rx Axi DMA engine out of
* halted state. This will make the Rx side ready for reception.
*/
axienet_dma_out32(lp, XAXIDMA_RX_CDESC_OFFSET, lp->rx_bd_p);
axienet_dma_out_addr(lp, XAXIDMA_RX_CDESC_OFFSET, lp->rx_bd_p);
cr = axienet_dma_in32(lp, XAXIDMA_RX_CR_OFFSET);
axienet_dma_out32(lp, XAXIDMA_RX_CR_OFFSET,
cr | XAXIDMA_CR_RUNSTOP_MASK);
axienet_dma_out32(lp, XAXIDMA_RX_TDESC_OFFSET, lp->rx_bd_p +
(sizeof(*lp->rx_bd_v) * (lp->rx_bd_num - 1)));
axienet_dma_out_addr(lp, XAXIDMA_RX_TDESC_OFFSET, lp->rx_bd_p +
(sizeof(*lp->rx_bd_v) * (lp->rx_bd_num - 1)));
/* Write to the RS (Run-stop) bit in the Tx channel control register.
* Tx channel is now ready to run. But only after we write to the
* tail pointer register that the Tx channel will start transmitting.
*/
axienet_dma_out32(lp, XAXIDMA_TX_CDESC_OFFSET, lp->tx_bd_p);
axienet_dma_out_addr(lp, XAXIDMA_TX_CDESC_OFFSET, lp->tx_bd_p);
cr = axienet_dma_in32(lp, XAXIDMA_TX_CR_OFFSET);
axienet_dma_out32(lp, XAXIDMA_TX_CR_OFFSET,
cr | XAXIDMA_CR_RUNSTOP_MASK);
......@@ -757,7 +763,7 @@ axienet_start_xmit(struct sk_buff *skb, struct net_device *ndev)
tail_p = lp->tx_bd_p + sizeof(*lp->tx_bd_v) * lp->tx_bd_tail;
/* Start the transfer */
axienet_dma_out32(lp, XAXIDMA_TX_TDESC_OFFSET, tail_p);
axienet_dma_out_addr(lp, XAXIDMA_TX_TDESC_OFFSET, tail_p);
if (++lp->tx_bd_tail >= lp->tx_bd_num)
lp->tx_bd_tail = 0;
......@@ -849,7 +855,7 @@ static void axienet_recv(struct net_device *ndev)
ndev->stats.rx_bytes += size;
if (tail_p)
axienet_dma_out32(lp, XAXIDMA_RX_TDESC_OFFSET, tail_p);
axienet_dma_out_addr(lp, XAXIDMA_RX_TDESC_OFFSET, tail_p);
}
/**
......@@ -1671,18 +1677,18 @@ static void axienet_dma_err_handler(struct work_struct *work)
/* Populate the tail pointer and bring the Rx Axi DMA engine out of
* halted state. This will make the Rx side ready for reception.
*/
axienet_dma_out32(lp, XAXIDMA_RX_CDESC_OFFSET, lp->rx_bd_p);
axienet_dma_out_addr(lp, XAXIDMA_RX_CDESC_OFFSET, lp->rx_bd_p);
cr = axienet_dma_in32(lp, XAXIDMA_RX_CR_OFFSET);
axienet_dma_out32(lp, XAXIDMA_RX_CR_OFFSET,
cr | XAXIDMA_CR_RUNSTOP_MASK);
axienet_dma_out32(lp, XAXIDMA_RX_TDESC_OFFSET, lp->rx_bd_p +
(sizeof(*lp->rx_bd_v) * (lp->rx_bd_num - 1)));
axienet_dma_out_addr(lp, XAXIDMA_RX_TDESC_OFFSET, lp->rx_bd_p +
(sizeof(*lp->rx_bd_v) * (lp->rx_bd_num - 1)));
/* Write to the RS (Run-stop) bit in the Tx channel control register.
* Tx channel is now ready to run. But only after we write to the
* tail pointer register that the Tx channel will start transmitting
*/
axienet_dma_out32(lp, XAXIDMA_TX_CDESC_OFFSET, lp->tx_bd_p);
axienet_dma_out_addr(lp, XAXIDMA_TX_CDESC_OFFSET, lp->tx_bd_p);
cr = axienet_dma_in32(lp, XAXIDMA_TX_CR_OFFSET);
axienet_dma_out32(lp, XAXIDMA_TX_CR_OFFSET,
cr | XAXIDMA_CR_RUNSTOP_MASK);
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment