spi: tegra210-quad: Add support for hardware dummy cycles transfer

Tegra Quad SPI controller hardware supports sending dummy bytes based
on programmed dummy clock cycles after the actual transfer bytes.

This patch adds this support of hardware dummy bytes transfer and
skips transfer of dummy bytes from the software.

For dummy cycles more than Tegra Quad SPI hardware maximum dummy
cycles limit, driver transfers dummy bytes from the software.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Link: https://lore.kernel.org/r/1608585459-17250-7-git-send-email-skomatineni@nvidia.comSigned-off-by: Mark Brown <broonie@kernel.org>

drivers/spi/spi-tegra210-quad.c

@@ -117,6 +117,7 @@
 
 #define QSPI_MISC_REG                           0x194
 #define QSPI_NUM_DUMMY_CYCLE(x)			(((x) & 0xff) << 0)
+#define QSPI_DUMMY_CYCLES_MAX			0xff
 
 #define DATA_DIR_TX				BIT(0)
 #define DATA_DIR_RX				BIT(1)
@@ -170,6 +171,7 @@ struct tegra_qspi {
 	u32					def_command2_reg;
 	u32					spi_cs_timing1;
 	u32					spi_cs_timing2;
+	u8					dummy_cycles;
 
 	struct completion			xfer_completion;
 	struct spi_transfer			*curr_xfer;
@@ -856,6 +858,8 @@ static int tegra_qspi_start_transfer_one(struct spi_device *spi,
 
 	tqspi->command1_reg = command1;
 
+	tegra_qspi_writel(tqspi, QSPI_NUM_DUMMY_CYCLE(tqspi->dummy_cycles), QSPI_MISC_REG);
+
 	ret = tegra_qspi_flush_fifos(tqspi, false);
 	if (ret < 0)
 		return ret;
@@ -974,7 +978,7 @@ static int tegra_qspi_transfer_one_message(struct spi_master *master, struct spi
 {
 	struct tegra_qspi *tqspi = spi_master_get_devdata(master);
 	struct spi_device *spi = msg->spi;
-	struct spi_transfer *xfer;
+	struct spi_transfer *transfer;
 	bool is_first_msg = true;
 	int ret;
 
@@ -983,9 +987,33 @@ static int tegra_qspi_transfer_one_message(struct spi_master *master, struct spi
 	tqspi->tx_status = 0;
 	tqspi->rx_status = 0;
 
-	list_for_each_entry(xfer, &msg->transfers, transfer_list) {
+	list_for_each_entry(transfer, &msg->transfers, transfer_list) {
+		struct spi_transfer *xfer = transfer;
+		u8 dummy_bytes = 0;
 		u32 cmd1;
 
+		tqspi->dummy_cycles = 0;
+		/*
+		 * Tegra QSPI hardware supports dummy bytes transfer after actual transfer
+		 * bytes based on programmed dummy clock cycles in the QSPI_MISC register.
+		 * So, check if the next transfer is dummy data transfer and program dummy
+		 * clock cycles along with the current transfer and skip next transfer.
+		 */
+		if (!list_is_last(&xfer->transfer_list, &msg->transfers)) {
+			struct spi_transfer *next_xfer;
+
+			next_xfer = list_next_entry(xfer, transfer_list);
+			if (next_xfer->dummy_data) {
+				u32 dummy_cycles = next_xfer->len * 8 / next_xfer->tx_nbits;
+
+				if (dummy_cycles <= QSPI_DUMMY_CYCLES_MAX) {
+					tqspi->dummy_cycles = dummy_cycles;
+					dummy_bytes = next_xfer->len;
+					transfer = next_xfer;
+				}
+			}
+		}
+
 		reinit_completion(&tqspi->xfer_completion);
 
 		cmd1 = tegra_qspi_setup_transfer_one(spi, xfer, is_first_msg);
@@ -1016,7 +1044,7 @@ static int tegra_qspi_transfer_one_message(struct spi_master *master, struct spi
 			goto complete_xfer;
 		}
 
-		msg->actual_length += xfer->len;
+		msg->actual_length += xfer->len + dummy_bytes;
 
 complete_xfer:
 		if (ret < 0) {