Commit 6c930994 authored by Vladimir Oltean's avatar Vladimir Oltean Committed by David S. Miller

mii: Add helpers for parsing SGMII auto-negotiation

Typically a MAC PCS auto-configures itself after it receives the
negotiated copper-side link settings from the PHY, but some MAC devices
are more special and need manual interpretation of the SGMII AN result.

In other cases, the PCS exposes the entire tx_config_reg base page as it
is transmitted on the wire during auto-negotiation, so it makes sense to
be able to decode the equivalent lp_advertised bit mask from the raw u16
(of course, "lp" considering the PCS to be the local PHY).

Therefore, add the bit definitions for the SGMII registers 4 and 5
(local device ability, link partner ability), as well as a link_mode
conversion helper that can be used to feed the AN results into
phy_resolve_aneg_linkmode.
Signed-off-by: default avatarVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent de1b23b9
......@@ -372,6 +372,56 @@ static inline u32 mii_lpa_to_ethtool_lpa_x(u32 lpa)
return result | mii_adv_to_ethtool_adv_x(lpa);
}
/**
* mii_lpa_mod_linkmode_adv_sgmii
* @lp_advertising: pointer to destination link mode.
* @lpa: value of the MII_LPA register
*
* A small helper function that translates MII_LPA bits to
* linkmode advertisement settings for SGMII.
* Leaves other bits unchanged.
*/
static inline void
mii_lpa_mod_linkmode_lpa_sgmii(unsigned long *lp_advertising, u32 lpa)
{
u32 speed_duplex = lpa & LPA_SGMII_DPX_SPD_MASK;
linkmode_mod_bit(ETHTOOL_LINK_MODE_1000baseT_Half_BIT, lp_advertising,
speed_duplex == LPA_SGMII_1000HALF);
linkmode_mod_bit(ETHTOOL_LINK_MODE_1000baseT_Full_BIT, lp_advertising,
speed_duplex == LPA_SGMII_1000FULL);
linkmode_mod_bit(ETHTOOL_LINK_MODE_100baseT_Half_BIT, lp_advertising,
speed_duplex == LPA_SGMII_100HALF);
linkmode_mod_bit(ETHTOOL_LINK_MODE_100baseT_Full_BIT, lp_advertising,
speed_duplex == LPA_SGMII_100FULL);
linkmode_mod_bit(ETHTOOL_LINK_MODE_10baseT_Half_BIT, lp_advertising,
speed_duplex == LPA_SGMII_10HALF);
linkmode_mod_bit(ETHTOOL_LINK_MODE_10baseT_Full_BIT, lp_advertising,
speed_duplex == LPA_SGMII_10FULL);
}
/**
* mii_lpa_to_linkmode_adv_sgmii
* @advertising: pointer to destination link mode.
* @lpa: value of the MII_LPA register
*
* A small helper function that translates MII_ADVERTISE bits
* to linkmode advertisement settings when in SGMII mode.
* Clears the old value of advertising.
*/
static inline void mii_lpa_to_linkmode_lpa_sgmii(unsigned long *lp_advertising,
u32 lpa)
{
linkmode_zero(lp_advertising);
mii_lpa_mod_linkmode_lpa_sgmii(lp_advertising, lpa);
}
/**
* mii_adv_mod_linkmode_adv_t
* @advertising:pointer to destination link mode.
......
......@@ -131,6 +131,18 @@
#define NWAYTEST_LOOPBACK 0x0100 /* Enable loopback for N-way */
#define NWAYTEST_RESV2 0xfe00 /* Unused... */
/* MAC and PHY tx_config_Reg[15:0] for SGMII in-band auto-negotiation.*/
#define ADVERTISE_SGMII 0x0001 /* MAC can do SGMII */
#define LPA_SGMII 0x0001 /* PHY can do SGMII */
#define LPA_SGMII_DPX_SPD_MASK 0x1C00 /* SGMII duplex and speed bits */
#define LPA_SGMII_10HALF 0x0000 /* Can do 10mbps half-duplex */
#define LPA_SGMII_10FULL 0x1000 /* Can do 10mbps full-duplex */
#define LPA_SGMII_100HALF 0x0400 /* Can do 100mbps half-duplex */
#define LPA_SGMII_100FULL 0x1400 /* Can do 100mbps full-duplex */
#define LPA_SGMII_1000HALF 0x0800 /* Can do 1000mbps half-duplex */
#define LPA_SGMII_1000FULL 0x1800 /* Can do 1000mbps full-duplex */
#define LPA_SGMII_LINK 0x8000 /* PHY link with copper-side partner */
/* 1000BASE-T Control register */
#define ADVERTISE_1000FULL 0x0200 /* Advertise 1000BASE-T full duplex */
#define ADVERTISE_1000HALF 0x0100 /* Advertise 1000BASE-T half duplex */
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment