net: mdio-mux-meson-g12a: force internal PHY off on mux switch

Force the internal PHY off then on when switching to the internal path.
This fixes problems where the PHY ID is not properly set.

Fixes: 70904251 ("net: phy: add amlogic g12a mdio mux support")
Suggested-by: Qi Duan <qi.duan@amlogic.com>
Co-developed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20230124101157.232234-1-jbrunet@baylibre.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

drivers/net/mdio/mdio-mux-meson-g12a.c

@@ -4,6 +4,7 @@
  */
 
 #include <linux/bitfield.h>
+#include <linux/delay.h>
 #include <linux/clk.h>
 #include <linux/clk-provider.h>
 #include <linux/device.h>
@@ -150,6 +151,7 @@ static const struct clk_ops g12a_ephy_pll_ops = {
 
 static int g12a_enable_internal_mdio(struct g12a_mdio_mux *priv)
 {
+	u32 value;
 	int ret;
 
 	/* Enable the phy clock */
@@ -163,18 +165,25 @@ static int g12a_enable_internal_mdio(struct g12a_mdio_mux *priv)
 
 	/* Initialize ephy control */
 	writel(EPHY_G12A_ID, priv->regs + ETH_PHY_CNTL0);
-	writel(FIELD_PREP(PHY_CNTL1_ST_MODE, 3) |
-	       FIELD_PREP(PHY_CNTL1_ST_PHYADD, EPHY_DFLT_ADD) |
-	       FIELD_PREP(PHY_CNTL1_MII_MODE, EPHY_MODE_RMII) |
-	       PHY_CNTL1_CLK_EN |
-	       PHY_CNTL1_CLKFREQ |
-	       PHY_CNTL1_PHY_ENB,
-	       priv->regs + ETH_PHY_CNTL1);
+
+	/* Make sure we get a 0 -> 1 transition on the enable bit */
+	value = FIELD_PREP(PHY_CNTL1_ST_MODE, 3) |
+		FIELD_PREP(PHY_CNTL1_ST_PHYADD, EPHY_DFLT_ADD) |
+		FIELD_PREP(PHY_CNTL1_MII_MODE, EPHY_MODE_RMII) |
+		PHY_CNTL1_CLK_EN |
+		PHY_CNTL1_CLKFREQ;
+	writel(value, priv->regs + ETH_PHY_CNTL1);
 	writel(PHY_CNTL2_USE_INTERNAL |
 	       PHY_CNTL2_SMI_SRC_MAC |
 	       PHY_CNTL2_RX_CLK_EPHY,
 	       priv->regs + ETH_PHY_CNTL2);
 
+	value |= PHY_CNTL1_PHY_ENB;
+	writel(value, priv->regs + ETH_PHY_CNTL1);
+
+	/* The phy needs a bit of time to power up */
+	mdelay(10);
+
 	return 0;
 }