Commit 70991f1e authored by Ioana Ciornei's avatar Ioana Ciornei Committed by Jakub Kicinski

dt-bindings: net: convert sff,sfp to dtschema

Convert the sff,sfp.txt bindings to the DT schema format.
Also add the new path to the list of maintained files.
Signed-off-by: default avatarIoana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: default avatarRob Herring <robh@kernel.org>
Signed-off-by: default avatarJakub Kicinski <kuba@kernel.org>
parent 5022e221
Small Form Factor (SFF) Committee Small Form-factor Pluggable (SFP)
Transceiver
Required properties:
- compatible : must be one of
"sff,sfp" for SFP modules
"sff,sff" for soldered down SFF modules
- i2c-bus : phandle of an I2C bus controller for the SFP two wire serial
interface
Optional Properties:
- mod-def0-gpios : GPIO phandle and a specifier of the MOD-DEF0 (AKA Mod_ABS)
module presence input gpio signal, active (module absent) high. Must
not be present for SFF modules
- los-gpios : GPIO phandle and a specifier of the Receiver Loss of Signal
Indication input gpio signal, active (signal lost) high
- tx-fault-gpios : GPIO phandle and a specifier of the Module Transmitter
Fault input gpio signal, active (fault condition) high
- tx-disable-gpios : GPIO phandle and a specifier of the Transmitter Disable
output gpio signal, active (Tx disable) high
- rate-select0-gpios : GPIO phandle and a specifier of the Rx Signaling Rate
Select (AKA RS0) output gpio signal, low: low Rx rate, high: high Rx rate
Must not be present for SFF modules
- rate-select1-gpios : GPIO phandle and a specifier of the Tx Signaling Rate
Select (AKA RS1) output gpio signal (SFP+ only), low: low Tx rate, high:
high Tx rate. Must not be present for SFF modules
- maximum-power-milliwatt : Maximum module power consumption
Specifies the maximum power consumption allowable by a module in the
slot, in milli-Watts. Presently, modules can be up to 1W, 1.5W or 2W.
Example #1: Direct serdes to SFP connection
sfp_eth3: sfp-eth3 {
compatible = "sff,sfp";
i2c-bus = <&sfp_1g_i2c>;
los-gpios = <&cpm_gpio2 22 GPIO_ACTIVE_HIGH>;
mod-def0-gpios = <&cpm_gpio2 21 GPIO_ACTIVE_LOW>;
maximum-power-milliwatt = <1000>;
pinctrl-names = "default";
pinctrl-0 = <&cpm_sfp_1g_pins &cps_sfp_1g_pins>;
tx-disable-gpios = <&cps_gpio1 24 GPIO_ACTIVE_HIGH>;
tx-fault-gpios = <&cpm_gpio2 19 GPIO_ACTIVE_HIGH>;
};
&cps_emac3 {
phy-names = "comphy";
phys = <&cps_comphy5 0>;
sfp = <&sfp_eth3>;
};
Example #2: Serdes to PHY to SFP connection
sfp_eth0: sfp-eth0 {
compatible = "sff,sfp";
i2c-bus = <&sfpp0_i2c>;
los-gpios = <&cps_gpio1 28 GPIO_ACTIVE_HIGH>;
mod-def0-gpios = <&cps_gpio1 27 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&cps_sfpp0_pins>;
tx-disable-gpios = <&cps_gpio1 29 GPIO_ACTIVE_HIGH>;
tx-fault-gpios = <&cps_gpio1 26 GPIO_ACTIVE_HIGH>;
};
p0_phy: ethernet-phy@0 {
compatible = "ethernet-phy-ieee802.3-c45";
pinctrl-names = "default";
pinctrl-0 = <&cpm_phy0_pins &cps_phy0_pins>;
reg = <0>;
interrupt = <&cpm_gpio2 18 IRQ_TYPE_EDGE_FALLING>;
sfp = <&sfp_eth0>;
};
&cpm_eth0 {
phy = <&p0_phy>;
phy-mode = "10gbase-kr";
};
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: "http://devicetree.org/schemas/net/sff,sfp.yaml#"
$schema: "http://devicetree.org/meta-schemas/core.yaml#"
title: Small Form Factor (SFF) Committee Small Form-factor Pluggable (SFP)
Transceiver
maintainers:
- Russell King <linux@armlinux.org.uk>
properties:
compatible:
enum:
- sff,sfp # for SFP modules
- sff,sff # for soldered down SFF modules
i2c-bus:
$ref: /schemas/types.yaml#/definitions/phandle
description:
phandle of an I2C bus controller for the SFP two wire serial
maximum-power-milliwatt:
maxItems: 1
description:
Maximum module power consumption Specifies the maximum power consumption
allowable by a module in the slot, in milli-Watts. Presently, modules can
be up to 1W, 1.5W or 2W.
"mod-def0-gpios":
maxItems: 1
description:
GPIO phandle and a specifier of the MOD-DEF0 (AKA Mod_ABS) module
presence input gpio signal, active (module absent) high. Must not be
present for SFF modules
"los-gpios":
maxItems: 1
description:
GPIO phandle and a specifier of the Receiver Loss of Signal Indication
input gpio signal, active (signal lost) high
"tx-fault-gpios":
maxItems: 1
description:
GPIO phandle and a specifier of the Module Transmitter Fault input gpio
signal, active (fault condition) high
"tx-disable-gpios":
maxItems: 1
description:
GPIO phandle and a specifier of the Transmitter Disable output gpio
signal, active (Tx disable) high
"rate-select0-gpios":
maxItems: 1
description:
GPIO phandle and a specifier of the Rx Signaling Rate Select (AKA RS0)
output gpio signal, low - low Rx rate, high - high Rx rate Must not be
present for SFF modules
"rate-select1-gpios":
maxItems: 1
description:
GPIO phandle and a specifier of the Tx Signaling Rate Select (AKA RS1)
output gpio signal (SFP+ only), low - low Tx rate, high - high Tx rate. Must
not be present for SFF modules
allOf:
- if:
properties:
compatible:
contains:
const: sff,sff
then:
properties:
mod-def0-gpios: false
rate-select0-gpios: false
rate-select1-gpios: false
required:
- compatible
- i2c-bus
additionalProperties: false
examples:
- | # Direct serdes to SFP connection
#include <dt-bindings/gpio/gpio.h>
sfp_eth3: sfp-eth3 {
compatible = "sff,sfp";
i2c-bus = <&sfp_1g_i2c>;
los-gpios = <&cpm_gpio2 22 GPIO_ACTIVE_HIGH>;
mod-def0-gpios = <&cpm_gpio2 21 GPIO_ACTIVE_LOW>;
maximum-power-milliwatt = <1000>;
pinctrl-names = "default";
pinctrl-0 = <&cpm_sfp_1g_pins &cps_sfp_1g_pins>;
tx-disable-gpios = <&cps_gpio1 24 GPIO_ACTIVE_HIGH>;
tx-fault-gpios = <&cpm_gpio2 19 GPIO_ACTIVE_HIGH>;
};
cps_emac3 {
phy-names = "comphy";
phys = <&cps_comphy5 0>;
sfp = <&sfp_eth3>;
};
- | # Serdes to PHY to SFP connection
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
sfp_eth0: sfp-eth0 {
compatible = "sff,sfp";
i2c-bus = <&sfpp0_i2c>;
los-gpios = <&cps_gpio1 28 GPIO_ACTIVE_HIGH>;
mod-def0-gpios = <&cps_gpio1 27 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&cps_sfpp0_pins>;
tx-disable-gpios = <&cps_gpio1 29 GPIO_ACTIVE_HIGH>;
tx-fault-gpios = <&cps_gpio1 26 GPIO_ACTIVE_HIGH>;
};
mdio {
#address-cells = <1>;
#size-cells = <0>;
p0_phy: ethernet-phy@0 {
compatible = "ethernet-phy-ieee802.3-c45";
pinctrl-names = "default";
pinctrl-0 = <&cpm_phy0_pins &cps_phy0_pins>;
reg = <0>;
interrupt = <&cpm_gpio2 18 IRQ_TYPE_EDGE_FALLING>;
sfp = <&sfp_eth0>;
};
};
cpm_eth0 {
phy = <&p0_phy>;
phy-mode = "10gbase-kr";
};
......@@ -18189,6 +18189,7 @@ SFF/SFP/SFP+ MODULE SUPPORT
M: Russell King <linux@armlinux.org.uk>
L: netdev@vger.kernel.org
S: Maintained
F: Documentation/devicetree/bindings/net/sff,sfp.yaml
F: drivers/net/phy/phylink.c
F: drivers/net/phy/sfp*
F: include/linux/mdio/mdio-i2c.h
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment