enic: Add sriov vf device id checks in port profile code

This patch adds checks for sriov vf's in enic port profile handling code.
sriov vf's are same as dynamic vnics but with a different device id.
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: Sujith Sankar <ssujith@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/cisco/enic/enic_main.c

@@ -444,7 +444,7 @@ static void enic_mtu_check(struct enic *enic)
 
 	if (mtu && mtu != enic->port_mtu) {
 		enic->port_mtu = mtu;
-		if (enic_is_dynamic(enic)) {
+		if (enic_is_dynamic(enic) || enic_is_sriov_vf(enic)) {
 			mtu = max_t(int, ENIC_MIN_MTU,
 				min_t(int, ENIC_MAX_MTU, mtu));
 			if (mtu != netdev->mtu)
@@ -856,7 +856,7 @@ static int enic_set_mac_addr(struct net_device *netdev, char *addr)
 {
 	struct enic *enic = netdev_priv(netdev);
 
-	if (enic_is_dynamic(enic)) {
+	if (enic_is_dynamic(enic) || enic_is_sriov_vf(enic)) {
 		if (!is_valid_ether_addr(addr) && !is_zero_ether_addr(addr))
 			return -EADDRNOTAVAIL;
 	} else {
@@ -1615,7 +1615,7 @@ static int enic_open(struct net_device *netdev)
 	for (i = 0; i < enic->rq_count; i++)
 		vnic_rq_enable(&enic->rq[i]);
 
-	if (!enic_is_dynamic(enic))
+	if (!enic_is_dynamic(enic) && !enic_is_sriov_vf(enic))
 		enic_dev_add_station_addr(enic);
 
 	enic_set_rx_mode(netdev);
@@ -1666,7 +1666,7 @@ static int enic_stop(struct net_device *netdev)
 	netif_carrier_off(netdev);
 	netif_tx_disable(netdev);
 
-	if (!enic_is_dynamic(enic))
+	if (!enic_is_dynamic(enic) && !enic_is_sriov_vf(enic))
 		enic_dev_del_station_addr(enic);
 
 	for (i = 0; i < enic->wq_count; i++) {
@@ -1703,7 +1703,7 @@ static int enic_change_mtu(struct net_device *netdev, int new_mtu)
 	if (new_mtu < ENIC_MIN_MTU || new_mtu > ENIC_MAX_MTU)
 		return -EINVAL;
 
-	if (enic_is_dynamic(enic))
+	if (enic_is_dynamic(enic) || enic_is_sriov_vf(enic))
 		return -EOPNOTSUPP;
 
 	if (running)
@@ -2433,7 +2433,7 @@ static int __devinit enic_probe(struct pci_dev *pdev,
 	 * called later by an upper layer.
 	 */
 
-	if (!enic_is_dynamic(enic)) {
+	if (!enic_is_dynamic(enic) && !enic_is_sriov_vf(enic)) {
 		err = vnic_dev_init(enic->vdev, 0);
 		if (err) {
 			dev_err(dev, "vNIC dev init failed, aborting\n");
@@ -2467,8 +2467,7 @@ static int __devinit enic_probe(struct pci_dev *pdev,
 	(void)enic_change_mtu(netdev, enic->port_mtu);
 
 #ifdef CONFIG_PCI_IOV
-	if (enic_is_dynamic(enic) && pdev->is_virtfn &&
-		is_zero_ether_addr(enic->mac_addr))
+	if (enic_is_sriov_vf(enic) && is_zero_ether_addr(enic->mac_addr))
 		random_ether_addr(enic->mac_addr);
 #endif
 
@@ -2481,7 +2480,7 @@ static int __devinit enic_probe(struct pci_dev *pdev,
 	enic->tx_coalesce_usecs = enic->config.intr_timer_usec;
 	enic->rx_coalesce_usecs = enic->tx_coalesce_usecs;
 
-	if (enic_is_dynamic(enic))
+	if (enic_is_dynamic(enic) || enic_is_sriov_vf(enic))
 		netdev->netdev_ops = &enic_netdev_dynamic_ops;
 	else
 		netdev->netdev_ops = &enic_netdev_ops;