Commit 757d2505 authored by Hans Verkuil's avatar Hans Verkuil Committed by Mauro Carvalho Chehab

V4L/DVB (3430): Add new internal VIDIOC_INT commands

- Add new internal VIDIOC_INT commands for setting the tuner mode,
for putting a chip into standby mode and to set/get the routing
of inputs/outputs of audio or video of a chip. These new commands
will replace older commands that are no longer up to the task.
Signed-off-by: default avatarHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: default avatarMauro Carvalho Chehab <mchehab@infradead.org>
parent ac272ed7
......@@ -115,12 +115,15 @@ enum v4l2_chip_ident {
};
/* audio ioctls */
/* v4l device was opened in Radio mode */
/* v4l device was opened in Radio mode, to be replaced by VIDIOC_INT_S_TUNER_MODE */
#define AUDC_SET_RADIO _IO('d',88)
/* select from TV,radio,extern,MUTE */
/* select from TV,radio,extern,MUTE, to be replaced with VIDIOC_INT_S_AUDIO_ROUTING */
#define AUDC_SET_INPUT _IOW('d',89,int)
/* msp3400 ioctl: will be removed in the near future */
/* msp3400 ioctl: will be removed in the near future, to be replaced by
VIDIOC_INT_S_AUDIO_ROUTING. */
struct msp_matrix {
int input;
int output;
......@@ -128,12 +131,25 @@ struct msp_matrix {
#define MSP_SET_MATRIX _IOW('m',17,struct msp_matrix)
/* tuner ioctls */
/* Sets tuner type and its I2C addr */
#define TUNER_SET_TYPE_ADDR _IOW('d',90,int)
/* Puts tuner on powersaving state, disabling it, except for i2c */
#define TUNER_SET_STANDBY _IOW('d',91,int)
#define TUNER_SET_TYPE_ADDR _IOW('d', 90, int)
/* Puts tuner on powersaving state, disabling it, except for i2c. To be replaced
by VIDIOC_INT_S_STANDBY. */
#define TUNER_SET_STANDBY _IOW('d', 91, int)
/* Sets tda9887 specific stuff, like port1, port2 and qss */
#define TDA9887_SET_CONFIG _IOW('d',92,int)
#define TDA9887_SET_CONFIG _IOW('d', 92, int)
/* Switch the tuner to a specific tuner mode. Replacement of AUDC_SET_RADIO */
#define VIDIOC_INT_S_TUNER_MODE _IOW('d', 93, enum v4l2_tuner_type)
/* Generic standby command. Passing -1 (all bits set to 1) will put the whole
chip into standby mode, value 0 will make the chip fully active. Specific
bits can be used by certain chips to enable/disable specific subsystems.
Replacement of TUNER_SET_STANDBY. */
#define VIDIOC_INT_S_STANDBY _IOW('d', 94, u32)
/* only implemented if CONFIG_VIDEO_ADV_DEBUG is defined */
#define VIDIOC_INT_S_REGISTER _IOR ('d', 100, struct v4l2_register)
......@@ -181,4 +197,25 @@ struct msp_matrix {
If the frequency is not supported, then -EINVAL is returned. */
#define VIDIOC_INT_I2S_CLOCK_FREQ _IOW ('d', 108, u32)
/* Routing definition, device dependent. It specifies which inputs (if any)
should be routed to which outputs (if any). */
struct v4l2_routing {
u32 input;
u32 output;
};
/* These internal commands should be used to define the inputs and outputs
of an audio/video chip. They will replace AUDC_SET_INPUT.
The v4l2 API commands VIDIOC_S/G_INPUT, VIDIOC_S/G_OUTPUT,
VIDIOC_S/G_AUDIO and VIDIOC_S/G_AUDOUT are meant to be used by the
user. Internally these commands should be used to switch inputs/outputs
because only the driver knows how to map a 'Television' input to the precise
input/output routing of an A/D converter, or a DSP, or a video digitizer.
These four commands should only be sent directly to an i2c device, they
should not be broadcast as the routing is very device specific. */
#define VIDIOC_INT_S_AUDIO_ROUTING _IOW ('d', 109, struct v4l2_routing)
#define VIDIOC_INT_G_AUDIO_ROUTING _IOR ('d', 110, struct v4l2_routing *)
#define VIDIOC_INT_S_VIDEO_ROUTING _IOW ('d', 111, struct v4l2_routing)
#define VIDIOC_INT_G_VIDEO_ROUTING _IOR ('d', 112, struct v4l2_routing *)
#endif /* V4L2_COMMON_H_ */
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment