ARM: dts: STi: Introduce B2260 board

B2260 board is the STMicroelectronics 96Board
based on STiH410 soc :
  - 1GB DDR
  - On-Board USB combo WiFi/Bluetooth RTL8723BU
    with PCB soldered antenna
  - Ethernet 1000-BaseT
  - Sata
  - HDMI
  - 2 x USB2 type A
  - micro USB2 type AB
  - SD card slot
  - High speed connector (SD/I2C/USB interfaces)
  - Slow speed connector (UART/I2C/GPIO/SPI/PCM interfaces)
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>

arch/arm/boot/dts/Makefile

@@ -686,6 +686,7 @@ dtb-$(CONFIG_ARCH_SPEAR6XX) += \
 dtb-$(CONFIG_ARCH_STI) += \
 	stih407-b2120.dtb \
 	stih410-b2120.dtb \
+	stih410-b2260.dtb \
 	stih415-b2000.dtb \
 	stih415-b2020.dtb \
 	stih416-b2000.dtb \

arch/arm/boot/dts/stih410-b2260.dts

+/*
+ * Copyright (C) 2016 STMicroelectronics (R&D) Limited.
+ * Author: Patrice Chotard <patrice.chotard@st.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+#include "stih410.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "STiH410 B2260";
+	compatible = "st,stih410-b2260", "st,stih410";
+
+	chosen {
+		bootargs = "console=ttyAS1,115200";
+		linux,stdout-path = &uart1;
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x40000000 0x40000000>;
+	};
+
+	aliases {
+		ttyAS1 = &uart1;
+		ethernet0 = &ethernet0;
+	};
+
+	soc {
+
+		leds {
+			compatible = "gpio-leds";
+			user_green_1 {
+				label = "User_green_1";
+				gpios = <&pio1 3 GPIO_ACTIVE_LOW>;
+				linux,default-trigger = "heartbeat";
+				default-state = "off";
+			};
+
+			user_green_2 {
+				label = "User_green_2";
+				gpios = <&pio4 1 GPIO_ACTIVE_LOW>;
+				default-state = "off";
+			};
+
+			user_green_3 {
+				label = "User_green_3";
+				gpios = <&pio2 1 GPIO_ACTIVE_LOW>;
+				default-state = "off";
+			};
+
+			user_green_4 {
+				label = "User_green_4";
+				gpios = <&pio2 5 GPIO_ACTIVE_LOW>;
+				default-state = "off";
+			};
+		};
+
+		/* Low speed expansion connector */
+		uart0: serial@9830000 {
+			label = "LS-UART0";
+			status = "okay";
+		};
+
+		/* Low speed expansion connector */
+		uart1: serial@9831000 {
+			label = "LS-UART1";
+			status = "okay";
+		};
+
+		/* Low speed expansion connector */
+		spi0: spi@9844000 {
+			label = "LS-SPI0";
+			cs-gpio = <&pio30 3 0>;
+			status = "okay";
+		};
+
+		/* Low speed expansion connector */
+		i2c0: i2c@9840000 {
+			label = "LS-I2C0";
+			status = "okay";
+		};
+
+		/* Low speed expansion connector */
+		i2c1: i2c@9841000 {
+			label = "LS-I2C1";
+			status = "okay";
+		};
+
+		/* high speed expansion connector */
+		i2c2: i2c@9842000 {
+			label = "HS-I2C2";
+			pinctrl-0 = <&pinctrl_i2c2_alt2_1>;
+			status = "okay";
+		};
+
+		/* high speed expansion connector */
+		i2c3: i2c@9843000 {
+			label = "HS-I2C3";
+			pinctrl-0 = <&pinctrl_i2c3_alt3_0>;
+			status = "okay";
+		};
+
+		mmc0: sdhci@09060000 {
+			pinctrl-0 = <&pinctrl_sd0>;
+			bus-width = <4>;
+			status = "okay";
+		};
+
+		/* high speed expansion connector */
+		mmc1: sdhci@09080000 {
+			status = "okay";
+		};
+
+		pwm0: pwm@9810000 {
+			status = "okay";
+		};
+
+		pwm1: pwm@9510000 {
+			status = "okay";
+		};
+
+		usb2_picophy1: phy2 {
+			status = "okay";
+		};
+
+		usb2_picophy2: phy3 {
+			status = "okay";
+		};
+
+		ohci0: usb@9a03c00 {
+			status = "okay";
+		};
+
+		ehci0: usb@9a03e00 {
+			status = "okay";
+		};
+
+		ohci1: usb@9a83c00 {
+			status = "okay";
+		};
+
+		ehci1: usb@9a83e00 {
+			status = "okay";
+		};
+
+		ethernet0: dwmac@9630000 {
+			phy-mode = "rgmii";
+			pinctrl-0 = <&pinctrl_rgmii1 &pinctrl_rgmii1_mdio_1>;
+
+			snps,phy-bus-name = "stmmac";
+			snps,phy-bus-id = <0>;
+			snps,phy-addr = <0>;
+			snps,reset-gpio = <&pio0 7 0>;
+			snps,reset-active-low;
+			snps,reset-delays-us = <0 10000 1000000>;
+
+			status = "okay";
+		};
+
+		/* SSC11 to HDMI */
+		hdmiddc: i2c@9541000 {
+			/* HDMI V1.3a supports Standard mode only */
+			clock-frequency = <100000>;
+			st,i2c-min-scl-pulse-width-us = <0>;
+			st,i2c-min-sda-pulse-width-us = <5>;
+			status = "okay";
+		};
+
+		sti-display-subsystem {
+			sti_hdmi: sti-hdmi@8d04000 {
+				status = "okay";
+			};
+		};
+
+		miphy28lp_phy: miphy28lp@9b22000 {
+
+			phy_port1: port@9b2a000 {
+				st,osc-force-ext;
+			};
+		};
+
+		sata1: sata@9b28000 {
+			status = "okay";
+		};
+	};
+};